Odometer display
This function is used to adapt the odometer after the instrument cluster is replaced.
NOTE:
- Adaptation can only be performed on an instrument cluster with an odometer reading of no more than 62 miles.
- Adaptation can only be performed once for each instrument cluster.
- Only higher adaptation values can be entered (more than 62 miles).
- If an incorrect value is entered and confirmed, it cannot be changed. If this happens, the instrument cluster must be replaced.
- In countries where speedometers are calibrated in miles, adaptation can be performed in miles.
- Observe notes when replacing instrument cluster. See REPLACEMENT OF INSTRUMENT CLUSTER, INPUT VALUES .
Indicated on display
Fig 1: VAG 1551 Scan Tool Display - Odometer Display, Instrument Cluster With Maintenance Interval Extension (1 Of 13)
- Press buttons -1- and 1-. This selects "Logon Procedure" function 11.
Indicated on display
Fig 2: VAG 1551 Scan Tool Display - Odometer Display, Instrument Cluster With Maintenance Interval Extension (2 Of 13)
- Press -Q- button to confirm input.
Indicated on display
Fig 3: VAG 1551 Scan Tool Display - Odometer Display, Instrument Cluster With Maintenance Interval Extension (3 Of 13)
- Input code number 13861.
Indicated on display
Fig 4: VAG 1551 Scan Tool Display - Odometer Display, Instrument Cluster With Maintenance Interval Extension (4 Of 13)
- Press -Q- button to confirm input.
Indicated on display
Fig 5: VAG 1551 Scan Tool Display - Odometer Display, Instrument Cluster With Maintenance Interval Extension (5 Of 13)
- Press buttons -1- and -0-.
Indicated on display
Fig 6: VAG 1551 Scan Tool Display - Odometer Display, Instrument Cluster With Maintenance Interval Extension (6 Of 13)
- Press -Q- button to confirm input.
Indicated on display
Fig 7: VAG 1551 Scan Tool Display - Odometer Display, Instrument Cluster With Maintenance Interval Extension (7 Of 13)
- Press buttons -0- and -9-.
- Press -Q- button to confirm input.
Indicated on display
Fig 8: VAG 1551 Scan Tool Display - Odometer Display, Instrument Cluster With Maintenance Interval Extension (8 Of 13)
NOTE:
For the VAG1551 scan tool values can only be input via direct input.
- Press the --> button to continue program sequence.
Indicated on display
Fig 9: VAG 1551 Scan Tool Display - Odometer Display, Instrument Cluster With Maintenance Interval Extension (9 Of 13)
- Input adaptation value using keypad.
Example:
Mileage = 89627
0 8 9 6 3
ENTERING INPUT ADAPTATION VALUE 89627 MILEAGE
| X | Hundred thousands: 100000 ... 655350 | ||||
| X | Ten thousands: 10000 ... 90000 | ||||
| X | Thousands: 1000 ... 9000 | ||||
| X | Hundreds: 100 ... 900 | ||||
| X | Tens: 10 ... 90 miles | ||||
| Ones: round to nearest ten |
Indicated on display
Fig 10: VAG 1551 Scan Tool Display - Odometer Display, Instrument Cluster With Maintenance Interval Extension (10 Of 13)
- Press -Q- button to confirm input.
Indicated on display
Fig 11: VAG 1551 Scan Tool Display - Odometer Display, Instrument Cluster With Maintenance Interval Extension (11 Of 13)
- Press -Q- button to confirm input.
Indicated on display
Fig 12: VAG 1551 Scan Tool Display - Odometer Display, Instrument Cluster With Maintenance Interval Extension (12 Of 13)
- Press -Q- button to confirm input.
Indicated on display
Fig 13: VAG 1551 Scan Tool Display - Odometer Display, Instrument Cluster With Maintenance Interval Extension (13 Of 13)
- End adaptation of odometer by pressing the --> button.