Parking Assistance, Rear: Notes

NOTE:

During installation, the car and components must maintain a temperature of at least +20° C (68° F).

Fig 1: View Of Sensor Cleaning

Courtesy of VOLVO CARS OF NORTH AMERICA.

Clean the sensors. Use: Isopropanol.
Allow to dry.

Fig 2: Mat Down The Surface

Courtesy of VOLVO CARS OF NORTH AMERICA.

Carefully mat down the surface. Use Glasspaper, grade P1000.

Fig 3: View Of Sensor Cleaning

Courtesy of VOLVO CARS OF NORTH AMERICA.

Clean the sensors again. Use: Isopropanol.
Allow to dry.
Avoid contact with the cleaned surfaces.

Fig 4: Cleaning The Cradles

Courtesy of VOLVO CARS OF NORTH AMERICA.

Clean the cradles. Use: Isopropanol.
Allow to dry.
Avoid contact with the cleaned surfaces.

Fig 5: Applying Primer To Sensor Surface

Courtesy of VOLVO CARS OF NORTH AMERICA.

Apply a thin and even layer of primer to the cleaned plastic surface.
CAUTION:
Not on the center of the sensor.
Use: Bonding primer for plastic. P/N: 31335448.
HINT: Spray primer into the cap of the can and apply with a brush.

CAUTION:
Allow to dry at a temperature of at least +20°C for 10 min, before painting.

NOTE:

Also read the instructions on the spray can.

Fig 6: View Of Painted Sensors Area

Courtesy of VOLVO CARS OF NORTH AMERICA.

Apply primer to the cleaned surface. Use: Bonding primer for plastic. P/N: 31335448.
CAUTION:
Allow to dry at a temperature of at least +20°C for 10 min, before painting.

NOTE:

Also read the instructions on the spray can.

Fig 7: View Of Painted Sensors

Courtesy of VOLVO CARS OF NORTH AMERICA.

CAUTION:

Protect the connections' contact surfaces against paint.

Paint the sensors in the same color code as the vehicle.
Use Volvo Touch-up paint (Only use base coat.)
Use: Volvo 2-K Varnish. P/N: 31335447

NOTE:

Also read the instructions on the spray can.

Fig 8: View Of Painted Sensors Area

Courtesy of VOLVO CARS OF NORTH AMERICA.

Paint the holders in the same color code as the vehicle.
Use Volvo Touch-up paint (Only use base coat.)
Use: Volvo 2-K Varnish. P/N: 31335447

NOTE:

Also read the instructions on the spray can.

Fig 9: View Of Ignition Key In 0 Position

Courtesy of VOLVO CARS OF NORTH AMERICA.

Set the ignition key to position 0 .

NOTE:

Wait at least one minute before unplugging the connectors or removing other electrical equipment.

Fig 10: Removing Cargo Compartment Carpet

Courtesy of VOLVO CARS OF NORTH AMERICA.

Remove the cargo compartment carpet.

Fig 11: Identifying Sill Trim Panel

Courtesy of VOLVO CARS OF NORTH AMERICA.

Prize off the four external clips at the front edge/bottom edge of the sill trim panel on the tailgate.
Pry up one of the corners of the sill trim panel so that the two clips at that end release. Use a weatherstrip tool.
Pull up the sill trim panel so the remaining six clips release. Remove the panel.

Fig 12: Identifying Folded Seat Cushion And Backrest

Courtesy of VOLVO CARS OF NORTH AMERICA.

Fold the seat cushion and backrest on the right-hand side of the rear seat forward.

Fig 13: Identifying Removal Of Right-Hand Side Cushion

Courtesy of VOLVO CARS OF NORTH AMERICA.

Grasp the upper edge of the right-hand side cushion. Pull the side cushion forward so that the clip on the reverse releases.
Slide the side cushion up. Remove the side cushion.

Fig 14: Identifying Cover Panel Screws

Courtesy of VOLVO CARS OF NORTH AMERICA.

Remove the screw.
Pull the panel upwards so that the four clips on the inside release. Remove the panel.

Fig 15: Removing Side Panel

Courtesy of VOLVO CARS OF NORTH AMERICA.

Fold out the anchorage eyelets. Insert a scriber with an angled tip into the holes in the top of the covers (1). Turn the scriber so that the tip engages the reverse of the cover. Pull the covers off.
Remove the screws from the anchorage eyelets (2).
Remove the screw (3).
Pull off the side panel at the top so that the two clips at the rear/bottom of the side window and the clip at the bottom of the D-pillar release.
Disconnect the connector for the 12V socket, if present.
Lift out the side panel.

Fig 16: Removing Four Bumper Screws

Courtesy of VOLVO CARS OF NORTH AMERICA.

Remove the four bumper screws.

Fig 17: Identifying Rear Edge Bumper Screws

Courtesy of VOLVO CARS OF NORTH AMERICA.

Remove the five screws (1) holding the bumper cover at the rear edge of the wing liner in the rear wheel arch. Repeat on the other side.

Fig 18: View Of Bumper Cover Catches

Courtesy of VOLVO CARS OF NORTH AMERICA.

Remove the end of the bumper cover. Grasp the bumper cover inside the wing liner. Pull carefully until the six catches at the top edge release. Repeat on the other side.

Fig 19: Removing Bumper Cover

Courtesy of VOLVO CARS OF NORTH AMERICA.

Remove the bumper cover by pulling it straight backwards.

NOTE:

It is recommended that two people lift down the bumper cover.

Place the bumper cover on an underlay which will not damage the paint.

Fig 20: Marking on Inside of Bumper Cover

Courtesy of VOLVO CARS OF NORTH AMERICA.

Make a mark in the center of the markings on the inside of the bumper cover using a scriber.

Fig 21: Drilling on Center in 2 Steps

Courtesy of VOLVO CARS OF NORTH AMERICA.

Drill out the center of the markings.
1. 1. 3 mm (7/64")
2. 2. 10 mm (25/64")

Fig 22: Identifying Hole Cutting Tool (9997345)

Courtesy of VOLVO CARS OF NORTH AMERICA.

Use hole tool part no. 9997345 to make holes in the bumper cover. Check that the markings (1) are opposite each other when using the tool.

Fig 23: Using Tool (9997345) to Enlarge Pilot Holes

Courtesy of VOLVO CARS OF NORTH AMERICA.

CAUTION:

Place the hole tool's support sleeve on the inside, and the cutting part on the outside of the bumper casing.

Make the holes in the bumper cover using the hole tool.
Screw the hole tool together until it has cut the hole in the bumper cover.
Remove the plastic pieces from the hole tool and make the remaining holes in the same way.

Fig 24: Cleaning Inside of Bumper Cover

Courtesy of VOLVO CARS OF NORTH AMERICA.

Clean the inside of the bumper cover using a mild soap solution. Clean an area around the holes that is slightly larger than the sensor cradle. Use: Isopropanol.
Allow to dry.

Fig 25: Cleaning the Contacting Surfaces

Courtesy of VOLVO CARS OF NORTH AMERICA.

Clean the cradles on the surfaces as illustrated. Use: Isopropanol.
Allow to dry.

Fig 26: Apply Activator to Cleaned Surfaces

Courtesy of VOLVO CARS OF NORTH AMERICA.

Apply a thin and even layer of activator to the cleaned surfaces where the tape is to be attached. Use: 8637076.
Allow to dry.

Fig 27: Apply Activator to Cleaned Surfaces

Courtesy of VOLVO CARS OF NORTH AMERICA.

Apply a thin and even layer of activator to the cleaned surfaces where the tape is to be attached. Use: 8637076.
Allow to dry for at least 10 minutes.

Fig 28: Identifying Rubber Grommet For Removal

Courtesy of VOLVO CARS OF NORTH AMERICA.

Remove the rubber grommet from the hole in the car, it shall not be re-used.