Checking Ignition Switch

Fig 1: Identifying Ignition OFF

Courtesy of VOLVO CARS OF NORTH AMERICA.

• Click on the VCT2000 symbol.
• Check the status for the switch for key-in.

HINT: If the vehicle is equipped with Keyless vehicle module (KVM) always use the remote key in the ignition switch. 

Fig 2: Identifying VCT2000 Diagnostic Tool Symbol In VIDA

Courtesy of VOLVO CARS OF NORTH AMERICA.

Is the function OK? 

• YES 

  Refer to CHECKING UNLOCKED STEERING WHEEL LOCK 

• NO 

  Refer to REPLACING START CONTROL UNIT (SCU) 

• Click on the VCT2000 symbol.
• Check that the status of the ignition switch corresponds to all key positions.

  Compare with table in link below.

HINT: If the vehicle is equipped with Keyless vehicle module (KVM) always use the remote key in the ignition switch. 

Other information 

• For table, see:

  see DESCRIPTION OF SWITCH FOR START CONTROL UNIT (SCU)

Fig 1: Identifying VCT2000 Diagnostic Tool Symbol In VIDA

Courtesy of VOLVO CARS OF NORTH AMERICA.

Are all key positions OK? 

• YES 

  Refer to CHECKING STARTER MOTOR CIRCUIT 

• NO 

  Refer to REPLACING START CONTROL UNIT (SCU) 

• Click on the VCT2000 symbol.
• Check that the status of the ignition switch corresponds to all key positions.

  Compare with table in link below.

HINT: If the vehicle is equipped with Keyless vehicle module (KVM) always use the remote key in the ignition switch. 

Other information 

• For table, see:

  see DESCRIPTION OF SWITCH FOR START CONTROL UNIT (SCU)

Fig 1: Identifying VCT2000 Diagnostic Tool Symbol In VIDA

Courtesy of VOLVO CARS OF NORTH AMERICA.

Are all key positions OK? 

• YES 

  Refer to FAULT-TRACING INFORMATION 

• NO 

  Refer to CHECKING WIRING 

• Click on the VCT2000 symbol.
• Check that the status of the ignition switch corresponds to all key positions.

  Compare with table in link below.

Other information 

• For table, see:

  see DESCRIPTION OF SWITCH FOR START CONTROL UNIT (SCU)

Fig 1: Identifying VCT2000 Diagnostic Tool Symbol In VIDA

Courtesy of VOLVO CARS OF NORTH AMERICA.

Are all key positions OK? 

• YES 

  Refer to VERIFICATION 

• NO 

  Refer to CHECKING IGNITION SWITCH 

Fig 1: Identifying Ignition ON

Courtesy of VOLVO CARS OF NORTH AMERICA.

• Change to another key belonging to the vehicle.
• Click on the VCT2000 symbol.
• Check that the status of the ignition switch corresponds to all key positions.

  Compare with table in link below.

If key positions' status cannot be read out, or if the shown key position is invalid, the Start Control Unit (SCU) is probably defective.

Other information 

• For table, see:

  see DESCRIPTION OF SWITCH FOR START CONTROL UNIT (SCU)

Fig 2: Identifying VCT2000 Diagnostic Tool Symbol In VIDA

Courtesy of VOLVO CARS OF NORTH AMERICA.

Are all key positions OK? 

• YES 

  Refer to PROGRAMMING NEW KEYS 

• NO 

  Refer to REPLACING START CONTROL UNIT (SCU) 

Fig 1: Identifying Ignition ON

Courtesy of VOLVO CARS OF NORTH AMERICA.

• Click on the VCT2000 symbol.
• Check that the status of the ignition switch corresponds to all key positions.

  Compare with table in link below.

Other information 

• For table, see: DESCRIPTION OF SWITCH FOR START CONTROL UNIT (SCU) 

Fig 2: Identifying VCT2000 Diagnostic Tool Symbol In VIDA

Courtesy of VOLVO CARS OF NORTH AMERICA.

Are all key positions OK? 

• YES 

  Refer to VERIFICATION 

• NO 

  Refer to FAULT-TRACING INFORMATION