Brake Booster, Bleeding - Removal & Installation (XC)

• Brakes
  • Brake bleeding unit, connecting
  • Brake pads rear, replacing
    • Notes
    • Preparations
    • Removing brake pads
    • Cleaning the brake caliper
    • Checking the brake disc
    • Installation
      • Notes
      • Lubricating the sliding surfaces
      • Installing the brake pads
      • Finishing
  • Parking brake self-adjustment, resetting
    • Notes
    • Removal
      • Removing soundproofing panels
      • Removing the OBDII bracket
      • Removing the relay box
      • Removing the parking brake pedal
      • Reset the parking brake to the zero position
    • Installation
      • Notes
      • Resetting the parking brake
      • Installing the parking brake pedal
      • Finishing
      • Installing the relay box in the passenger compartment
      • Installing the OBDII bracket and soundproofing panel
  • Parking brake, adjusting
    • Notes
    • Removal
      • Removing the panel
      • Adjusting the parking brake
    • Installation
      • Installing the panel
  • Pedal sensor, power brake booster, replacing
    • Notes
    • Preparatory work
    • Removal
      • Removing pedal position sensor
    • Installation
      • Installing pedal position sensor
  • Pressure sensor, master cylinder, replacing
    • Preparations for replacing the pressure sensor on the master cylinder
    • Removal
      • Preparations for checking the pressure sensor
      • Checking pressure sensor
      • Preparations before replacing the pressure sensor
      • Replacing the pressure sensor
    • Installation
      • Installing the pressure sensor
      • Checking the pressure sensors visually
      • Bleeding the brake system
      • Airing
      • Checking the brakes
      • Relay box - air cleaner (ACL) housing
      • Air cleaner (ACL)
    • Master cylinder, replacing (cars with naturally aspirated engine)
      • Notes
      • Preparatory work
      • Removal
        • Removing the torque rod
        • Disconnecting the connectors
        • Removing the brake pipe
        • Removing the master cylinder
      • Installation
        • Notes
        • Installing the master cylinder
        • Installing the brake pipes
        • Installing the connectors
        • Installing the torque rod
      • Finishing
    • Master cylinder, replacing (cars with turbocharger)
      • Notes
      • Preparatory work
      • Removal
        • Removing the torque rod
        • Disconnecting the connectors
        • Removing the brake pipe
        • Removing the master cylinder
      • Installation
        • Notes
        • Installing the master cylinder
        • Installing the brake pipes
        • Installing the connectors
        • Installing the torque rod
      • Finishing
    • Brake fluid reservoir, replacing
      • Removal
        • Preparations
        • Remove the cross member
      • Installation
        • Install the brake fluid reservoir
  • Reconditioning front brake calipers
    • Notes
    • Collect the brake fluid
    • Remove the securing spring and locating pins
    • Remove the brake caliper and brake pads
    • Remove the piston from the brake caliper
    • Cleaning and inspection
    • Install the piston in the brake caliper
    • Install the brake caliper
    • Pressure test the brake system
  • Replacing the power brake booster (DSTC)
    • Preparation
      • Disconnect the battery lead
    • Removal
      • Preparations for removing the power brake booster
      • Preparations for removing the ABS unit
      • Remove the ABS unit and bracket from the side member
      • Preparations for removing the master cylinder
      • Remove the master cylinder
      • Transfer the components to the new power brake booster
    • Installation
      • Install the power brake booster
      • Install the push rod for the power brake booster and the retaining clip on the brake pedal
      • Install the master cylinder
      • Install the connectors and vacuum hose
      • Install the ABS unit and the bracket
      • Install the brake pipes in the master cylinder and in the hydraulic modulator
      • Install the cross member
      • Checking the power brake booster