RTI (1999-2004): RTI: Preparations
Applies to cars with power seats
- Move the left front seat to its rearmost position.
- Turn the ignition key to position 0
- Remove the key from the ignition switch (does not apply to cars with automatic gearboxes)
- Disconnect the battery negative lead.
NOTE:
Wait at least five minutes before disassembling the connectors or removing other electrical equipment.
- Carefully remove the loudspeaker grille (1) on the dashboard. Use a weatherstrip tool or similar.
- Remove the screws (1). Remove the bracket (2).
Applies to cars with a centrally mounted loudspeaker
- Remove the three screws in the loudspeaker (1)
- Lift up the loudspeaker. Disconnect the connector (2)
- Place the loudspeaker to one side.
- Detach the panel (1) and the gear selector lever boot using a weatherstrip tool.
- Move the gear selector lever to its rearmost position
- Pull the panel (1) and the boot backwards. Turn the panel as shown
- Remove the screws (2) from the dashboard environment panel.
- Angle the dashboard environment panel outwards so that it is possible to insert a couple of fingers between the center console and the reverse of the panel
- Remove the dashboard environment panel by pulling it downward, maintaining the same angle. Some force is required because the panel is tightly installed
- Disconnect the connectors on the reverse of the dashboard environment panel. Place the dashboard environment panel to one side.
NOTE:
If any of the outer hooks break off, these must be repaired. The method for this can be found in the Workshop Manual in the section about the dashboard.
- Remove the screws (1) from the radio bracket
- Pull out the bracket and radio. Pull the lower corner while pressing downwards
- Disconnect the connectors on the radio. Place the bracket and the radio to one side.
- Move the left front seat to its rearmost position
- Remove the left side panel (1) from the center console by turning the clip and pulling the panel outwards and backwards
- Remove the sill trim panel (2) at the left-hand front door
- Remove the cover (3) and the screws (4) for the front mountings in the left-hand front seat.
- Tip the left-hand front seat backwards
- Push the floor carpet to one side so that the air ducts (1) are accessible.
- Remove the seat cushion from the left-hand rear seat (1). Lift the front edge of the cushion and then pull forwards
- Remove the sill trim panel (2) at the left-hand rear door.
- Remove the seat belts from the guide (1) on the right and left-hand side cushions
- Insert a hand down the side of the lower section of the left side cushion. Release the catches while lifting the side cushion. Place the cushion to one side
- Fold both backrests forward.
- Carefully lift the front edge of the parcel shelf panel until the clips (1) release
- Lift up the parcel shelf further until the locating pins (2) release from their holes
- Pull out the parcel shelf. Lay the parcel shelf on the folded backrests.
- Lift out the cargo compartment carpet
- Press the centers of the clips at the bottom of the folding side panel on the left-hand side. Press the clips until a click is heard
- Remove the two clips
- Remove the plastic nut at the front edge of the side panel
- Repeat the operation on the right-hand side.
- Turn the handle (1) on the right and left-hand sides. Turn the handle through 90°.
- Fold the side panels down. Lift the panels out. Place the left-hand side panel to one side (there is a new panel in the kit)
- Remove the two covers (2). Remove the screws (3) in the sill trim panel
- Grip the outer edges of the sill trim panel (4). Pull the panel inwards towards the center so that the clips release from the sides
- Disconnect the connectors (5) for the cargo compartment lamps
- Remove the sill trim panel. Pull the sill trim panel straight upwards so that the clips release from the rear cross member.
- Remove the clips (1) and the plastic nut in the left front side panel in the cargo compartment. It is easiest to access the front upper clip from the side of the rear seat
- Remove the front side panel.
Only applies to cars with a CD changer
- Remove the four screws (1) in the bracket for the CD changer
- Remove the CD changer with the bracket
- Remove the DIN cable and the cable with the blue connector from the rear end of the CD changer.