Digital Jukebox, S80, without RTI: Notes

• Move the left-hand front seat to its rear position.
• Turn the ignition switch to position 0.
• On cars with manual gearbox: Remove the ignition key.
• Disconnect the battery negative lead.
  NOTE: Wait at least five minutes before disconnecting the connectors or removing other electrical equipment.

• Detach the panel (1) with the gear selector lever boot using a weatherstrip tool.

• Move the gear selector lever to its rearmost position.
• Pull the panel (1) with boot rearward and turn as shown.
• Remove the screws (2) from the dashboard environment panel.

• Angle the dashboard environment panel outwards so that it is possible to insert a couple of fingers between the center console and the short side of the dashboard environment panel.
• Pull the dashboard environment panel downward maintaining the same angle and remove the dashboard environment panel. The panel is well secured, so some force is required to detach the panel. Unplug the connectors on the reverse side, and place the dashboard environment panel to one side.
  NOTE: If any of the outer hooks break off, these must be repaired. The method for this can be found in the Workshop Manual in the section about the dashboard.

• Remove the screws (1) in the radio bracket.
• Pull out the bracket with the radio. Pull the lower corner while pressing downwards.
• Unplug the connectors from the radio and the telephone keypad if applicable, and place the bracket with the radio to one side.

• Remove the side panel (1) on the center console. First twist the clip at the rear edge of the panel a 1/4 turn anti-clockwise. Pull the rear edge of the panel outwards and backwards.
• Remove the sill trim panel (2).

• Remove the seat cushion (1). First lift the front edge, pull it forwards and lift it out.

• Remove the sill molding for the left-hand rear door.

• Take the seat belts out of the guide (1) on the left-hand side bolster.
• Put your hand into the side of the lower section of the left-hand side bolster. Release the catch and lift the bolster at the same time. Place the bolster to one side.
• Fold the backrest forward.

• Lift out the cargo compartment carpet.
• Press in the center of the clips on the lower edge of the folding side panel on the left-hand side until a click is heard.
• Remove the two clips.
• Remove the plastic nut at the front/lower edge of the side panel.

• Turn the knob (1) on the left-hand side through 90°.
• Fold the side panel inwards and remove it.
• Lift out the side panel and place it to one side. There is a new panel in the kit.

• - Remove the clips (1) and plastic nut from the left front side panel in the cargo compartment. The front upper clip is most easily removed from the rear seat side.
• Remove the front side panel.

• Take the DIN cable from the kit, lift up the floor carpet and route it underneath, up between the front air duct (1) and the strut (2) for the center console.
  NOTE: Make sure that it is the connector with a guide pin which points upward as shown, which is routed to the radio socket.
• Route the cable through the compartment for the radio.
• Clamp the cable in the strut, using the clamp (3) from the kit.
• Route the cable on above and alongside the front air duct to the member (4) for the seat mounting.
• Clamp the cable at the existing cable harness (5).

• Route the cable (1) under the carpet, along the left-hand side of the car to the rear door.
• Route the cable further under and along the front cable duct (2). Continue along the right-hand side of the rear cable duct (3).

• Route the DIN cable (1) along the two cable ducts/cable harness (2) under the insulation panel and out through the hole in the body to the cargo compartment.
• Route the DIN cable under the four connectors in the front cable duct.

Applies to cars up to and including model year -2004 (CH-389999) 

• Take the cable harness for power supply (1) from the kit. Connect the ground lead to the rear ground terminal (2) under the seat cushion. Tighten to 10 Nm (7 lbf. ft.)  .
• Route the ground lead under the four connectors in the front cable duct.
• Route the power supply cables (1) along the rear cable duct (3) under the insulation panel and out through the hole in the body to the cargo compartment. Position the cable end with the two red/white (R/W) single cables and the two green connectors, and the long cable with the green connector (4) by the rear fuse holder.

Applies to cars from model year 2005- (CH 390000-) 

• - Take the cable (1) for power supply from the kit. Connect the ground lead to the existing ground terminal behind the battery. Tighten the screw to 10 Nm (7 lbf. ft.)  . Position the cable end with the two red/white (R/W) single cables (2) and the two green connectors, and the long cable with the green connector (3) by the rear fuse holder.
• Route the cable harness on the left-hand side of the cable duct