Installing The DVD Reader.

Fig 1: Removing RH Dashboard End Panel

Courtesy of VOLVO CARS OF NORTH AMERICA.

Remove the panel on the right-hand end of the dashboard by carefully prying it loose all around with a weatherstrip tool, until the three clips release.
NOTE:
Do not damage the dashboard.

Fig 2: Identifying Vent Clip

Courtesy of VOLVO CARS OF NORTH AMERICA.

Remove the clip which holds the vent to the air duct.

Fig 3: Identifying Rear Center Console Panel

Courtesy of VOLVO CARS OF NORTH AMERICA.

Open the glove compartment and remove any contents and the rubber mat.
Carefully pry off the panel inside the center console with a weatherstrip tool. It is fitted with two clips on each short side.
Pull the panel away downwards.

Fig 4: Identifying Screws For Glove Compartment Opening

Courtesy of VOLVO CARS OF NORTH AMERICA.

Remove the five screws in the opening to the glove compartment.

Fig 5: Identifying Front Section Of Glove Compartment And Connectors

Courtesy of VOLVO CARS OF NORTH AMERICA.

Remove the glove compartment front section. Pull it back until the two clips in the upper edge release, following which, detach the three connectors on the upper side.

Fig 6: Identifying Screw For Vent On Right-Hand Side

Courtesy of VOLVO CARS OF NORTH AMERICA.

Remove the screw to the air vent on the right-hand side. Pull it away from the connection and lay it aside.

Fig 7: Identifying Inner Section Of Glove Compartment

Courtesy of VOLVO CARS OF NORTH AMERICA.

Undo the screws securing the glove compartment inner section.
Pull out the glove compartment and put it to one side.

Fig 8: Identifying Soundproofing Panel Clips

Courtesy of VOLVO CARS OF NORTH AMERICA.

Remove the soundproofing panel on the right-hand side by first pressing in the center of the clips and then pulling the panel away with the clips.

Fig 9: Identifying MOST Loop And Foam Covers

Courtesy of VOLVO CARS OF NORTH AMERICA.

Detach the sill molding at the front edge of the right-hand front door.
Fold aside the floor carpet and remove the clip on the right-hand side, under the impact member, in order to access the foam covered connectors taped at the existing cable harness.
Remove the cables from the tape and remove the foam covers (2) and (3).
Remove the MOST loop located on the fibre optic cables (1).

(The illustration shows the connectors with foam covers and the MOST loop.)

Fig 10: Pulling Cables Up Over Impact Member

Courtesy of VOLVO CARS OF NORTH AMERICA.

Carefully pull the cables up over the impact member and make sure that the fibre optic cables are bent to a radius greater than 25 mm (1") .

Fig 11: Identifying Hooks

Courtesy of VOLVO CARS OF NORTH AMERICA.

Take the DVD reader from the kit.
Fit the DVD reader in the inner section of the glove compartment with the hooks (1).
Lift up the DVD and the glove compartment so that the cables routed to the sockets on the rear of the DVD reader can be connected.

Fig 12: Identifying DVD Reader Cable Ports

Courtesy of VOLVO CARS OF NORTH AMERICA.

Connect the cables to the rear of the DVD reader:
1. Cable (1) DIN cable to the screen
2. Cable (2) fibre optic cable to the audio system
3. Cable (3) with green connector to the power supply

NOTE:

Make sure that the cable harness is not compressed behind the DVD reader. The fibre optic cables are especially sensitive and must not be bent to a radius of less than 25 mm (1').

Fig 13: Identifying Screws For DVD Reader

Courtesy of VOLVO CARS OF NORTH AMERICA.

Fold back the carpet, press in the clip and reinstall the sill trim panel.
Fit the inner section of the glove compartment in its correct position.
Use the screws (3) which were previously removed and screw in both the DVD reader bracket and the glove compartment.
Refit the soundproofing panel and secure it using the clips which were previously removed.
Reinstall the air duct.
Connect the connectors to the front section of the glove compartment.
Reinstall the front section of the glove compartment.
Reinstall the panel inside the center console.
Reinstall the clip for the air vent.
Reinstall the panel on the right-hand end of the dashboard.
Reinstall the rubber mat and any glove compartment contents.