Rear wheel hub, replacing: Removal

Removing rear wheels 

Fig 1: Rear Wheel

Courtesy of VOLVO CARS OF NORTH AMERICA.

Remove the rear wheel.

Removing the brake calliper and brake disc 

Fig 2: Brake Caliper And Brake Disc

Courtesy of VOLVO CARS OF NORTH AMERICA.

Remove: 

• the wheel sensor cable from the retainer on the brake hose
• the brake calliper mounting screws.

  Suspend the calliper in a steel wire.

• the brake disc locating pin/screw
• the brake disc.

Removing the wheel sensor 

Fig 3: Identifying Sensor From Wheel Spindle Removal

Courtesy of VOLVO CARS OF NORTH AMERICA.

Clean the area around the wheel sensor and remove the screw.

Carefully remove the sensor from the wheel spindle.

Bind the sensor so it is well protected.

Installing the tensioner 

Install 9995659 . See Tensioner 999 5659, User instructions .

Support the rear suspension 500 mm up between the fender edge and the center of the wheel.

Removing the hub 

Fig 4: Hub Screws

Courtesy of VOLVO CARS OF NORTH AMERICA.

Remove: 

• the 4 screws
• the hub.

Removal of screw for drive shaft 

Fig 1: Identifying Installation Of Screw To Drive Shaft

Courtesy of VOLVO CARS OF NORTH AMERICA.

Remove: 

• the rear wheel
• the screw for the drive shaft.

9997251 , 9512923

Removing the brake calliper and brake disc 

Fig 2: Identifying Brake Disc, Brake Caliper & Screws

Courtesy of VOLVO CARS OF NORTH AMERICA.

Remove: 

• the wheel sensor lead from the holder on the brake hose
• the brake calliper mounting screws.

  Suspend the caliper with a steel wire.

• the brake disc locating pin/screw
• the brake disc.

Removing the wheel sensor 

Fig 3: Identifying Sensor From Wheel Spindle Removal

Courtesy of VOLVO CARS OF NORTH AMERICA.

Clean around the wheel sensor and remove the screw.

Carefully remove the sensor from the stub axle.

Tie up the sensor well protected.

Installing the tensioner 

Fit 9995659 as described in Tensioner 999 5659, User instructions .

Support the rear suspension 500 mm up between the wing edge and the center of the wheel.

Removing the hub 

Fig 4: Hub Screws

Courtesy of VOLVO CARS OF NORTH AMERICA.

Remove: 

• the 4 screws
• the hub.

Removal of screw for drive shaft 

Fig 1: Identifying Installation Of Screw To Drive Shaft

Courtesy of VOLVO CARS OF NORTH AMERICA.

Remove: 

• the rear wheel
• the screw for the drive shaft.

Fig 2: Driveshaft In Hub

Courtesy of VOLVO CARS OF NORTH AMERICA.

9997251 , 9512923

Removing the brake calliper and brake disc 

Fig 3: Identifying Brake Disc, Brake Caliper & Screws

Courtesy of VOLVO CARS OF NORTH AMERICA.

Remove: 

• the wheel sensor lead from the holder on the brake hose
• the brake calliper mounting screws.

  Suspend the caliper with a steel wire.

• the brake disc locating pin/screw
• the brake disc.

Removing the wheel sensor 

Fig 4: Identifying Sensor From Wheel Spindle Removal

Courtesy of VOLVO CARS OF NORTH AMERICA.

Clean around the wheel sensor and remove the screw.

Carefully remove the sensor from the stub axle.

Tie up the sensor well protected.

Installing the tensioner 

Fit 9995659 as described in Tensioner 999 5659, User instructions .

Support the rear suspension 500 mm up between the wing edge and the center of the wheel.

Removing the hub 

Fig 5: Hub Screws

Courtesy of VOLVO CARS OF NORTH AMERICA.

Remove: 

• the 4 screws
• the hub.