Applies to all models: Installing the amplifier
- Remove the covers (1) for the screws to the right-hand seat.
- Remove the screws (2) from the seat base.
- Unplug the connectors under the seat.
- Tip the seat back.
- Remove the panel (1) on the right-hand side of the center console. Turn the clip at the rear edge of the panel through 90°. Pull the rear edge of the panel outward and backward.
- Remove the sill molding (2) at the right-hand front door.
- Detach the carpet (3), by the front left mounting for the right-hand seat. Pull the carpet forward and to the right.
- Fasten up the carpet in the door stop with a cord.
- Fold the rear carpet (4) backwards at an angle.
- Connect the thick cable harness from the kit to the sockets in the amplifier.
- If there is a pre-routed cable (2) to the power supply under the right-hand seat, connect it. If not, connect the cable from the kit for the power supply to the amplifier.
- Install the amplifier with the two enclosed screws (1) and tighten.
- Route the power supply positive cable together with the cable harness running to the radio cut-out.
Applies to the S60/V70/XC70
Route the cable harness:
- under the cut-away tab (1) of the carpet at the left-hand front mounting for the right-hand seat.
- over the left-hand air duct (2), along the lower edge of the center console and on, in front of the air ducts (3) up to the dashboard environment panel cut-out. Following which, continue on to the radio cut-out.
- Route the ground lead (1) for the power supply (brown) under the carpet in the rear edge of the member for the front seat mounting, out to the right-hand side of the door sill.
- Route the cable under the existing cable harness on to the brown cable in the ground terminal at the front door pillar. Connect the cable to the frame (2).
- Clamp the cable together with the cable harness at the seat mounting member (3) and at the front door pillar (3).
- Remove the panel (1) on the left-hand side of the center console. Turn the clip at the rear edge of the panel through 90°, and pull the rear edge of the panel outward and backward.
- Remove the soundproofing panel (2) by removing the two screws (3) and then prizing down the rear edge until the three clips release.
NOTE:
On right-hand drive cars the fuse holder is located on the right-hand side. The positive cable is then routed the same way as the ground lead, and up from below along the A-pillar to the fuse holder.
- Remove the fuse holder cover.
- Remove the fuse holder (1) by prizing up the catch at the top and pulling outwards.
- Route the amplifier's positive cable from the radio cut-out behind the dashboard to the fuse holder.
- Route the cable down to the cable harness under the steering column. Clamp the cable and the cable harness with a tie strap.
- Route the cable to the left along the floor lighting cable and clamp these with a tie strap.
- Route the cable up to the fuse holder.
Applies to cars up to and including model year -2004 (S60 CH -424999, V70 CH -458999, XC70 CH -172999, S80 CH -389999)
- Connect the cable to position 17 on the rear of the fuse holder.
Applies to cars from model year 2005- (S60 CH 425000-, V70 CH 459000-, XC70 CH 173000-, S80 CH 390000-)
- Connect the cable to position 11 on the rear of the fuse holder.
Applies to all models
- Reinstall the fuse holder.
Applies to cars up to and including model year -2004 (S60 CH -424999, V70 CH -458999, XC70 CH -172999, S80 CH -389999)
- Install a 30A fuse in position 17.
Applies to cars from model year 2005- (S60 CH 425000-, V70 CH 459000-, XC70 CH 173000-, S80 CH 390000-)
- Install a 30A fuse at position 11.
Applies to all models
- Refit the fuse holder cover.