Adapter For Assembling Flushing Circuit, E-Golf From My 2014 With Heat Pump

WARNING: This page is about a different car, the 2023 Volkswagen Atlas. However, it is still accessible from the selected car via links, so may be relevant.

Required adapters for the connections to A/C compressor	Adapters necessary for the connections to the reservoir or receiver/dryer	Miscellaneous
Refrigerant Circuit, Cleaning: Low pressure side: Refrigerant Circuits Adapter Set 1 - Adapter 12:VAS 6338/12 connected to the A/C Service Station and the Refrigerant Circuit Adapter Set - Adapter:VAS 6338/48 High pressure side: Rinsing Adapter:VAS 6338/3A	Receiver/Dryer:-- Bridge the disassembled refrigerant lines at the receiver/dryer using a desiccant bag. Refrigerant Circuits Adapter Set 1 - Adapter 6:VAS 6338/6 or Adapter:VAS 6338/8 depending on the manufacturer, quantity: 2 Hose:VAS 6338/31 -- Install a new receiver/dryer (dryer) after flushing.	No expansion valve is installed in vehicles with a heat pump. -- The expansion valves Refrigerant Expansion Valve 1 - N636-, Refrigerant Expansion Valve 2 -N637- and Refrigerant Expansion Valve 3 -N638- must not be removed or replaced.-- Using the Vehicle Diagnostic Tester start the "Refrigerant circuit, charging" function in the "Basic setting". Doing so opens the electric valves on the refrigerant circuit. The function is active and can only be ended when the refrigerant circuit has been flushed. Keep the Vehicle Diagnostic Tester connected so that the valves stay open.
Clean the A/C compressor: Low-pressure side: Refrigerant Circuit Adapter Set - Adapter:VAS 6338/48 , Refrigerant Circuits Adapter Set 1 - Adapter 41:VAS 6338/41A High pressure side: Refrigerant Circuits Adapter Set 1 - Adapter 40:VAS 6338/40A

Required adapters for the connections to A/C compressor

Adapters necessary for the connections to the reservoir or receiver/dryer

Miscellaneous

Refrigerant Circuit, Cleaning:

Low pressure side: Refrigerant Circuits Adapter Set 1 - Adapter 12:VAS 6338/12 connected to the A/C Service Station and the Refrigerant Circuit Adapter Set - Adapter:VAS 6338/48
High pressure side: Rinsing Adapter:VAS 6338/3A

Receiver/Dryer:-- Bridge the disassembled refrigerant lines at the receiver/dryer using a desiccant bag.

Refrigerant Circuits Adapter Set 1 - Adapter 6:VAS 6338/6 or Adapter:VAS 6338/8 depending on the manufacturer, quantity: 2
Hose:VAS 6338/31

-- Install a new receiver/dryer (dryer) after flushing.

No expansion valve is installed in vehicles with a heat pump.

-- The expansion valves Refrigerant Expansion Valve 1 - N636-, Refrigerant Expansion Valve 2 -N637- and Refrigerant Expansion Valve 3 -N638- must not be removed or replaced.-- Using the Vehicle Diagnostic Tester start the "Refrigerant circuit, charging" function in the "Basic setting".

Doing so opens the electric valves on the refrigerant circuit.
The function is active and can only be ended when the refrigerant circuit has been flushed.
Keep the Vehicle Diagnostic Tester connected so that the valves stay open.

Clean the A/C compressor:

Low-pressure side: Refrigerant Circuit Adapter Set - Adapter:VAS 6338/48 , Refrigerant Circuits Adapter Set 1 - Adapter 41:VAS 6338/41A
High pressure side: Refrigerant Circuits Adapter Set 1 - Adapter 40:VAS 6338/40A

Condensers with an integrated receiver/dryer or dryer cartridge that cannot be replaced separately or is not available as a replacement part, the condenser must be replaced after flushing (with the dryer cartridge installed). Refer to Refrigerant Circuit (vehicle-specific service information) and the Parts Information.