Wheel Bearing Housing: Removing

WARNING: This page is about a different car, the 2016 Volkswagen Beetle, 2015 Volkswagen Beetle, 2014 Volkswagen Beetle, and 2013 Volkswagen Beetle. However, it is still accessible from the selected car via links, so may be relevant.

-- Remove the drive axle bolt. Refer to THREADED CONNECTION, LOOSENING AND TIGHTENING .

CAUTION:

The wheel bearing must not be under a load while the drive axle threaded connection on the wheel side is loose.

If the wheel bearings are under the load of the vehicle weight, the wheel bearing will be damaged. This reduces the service life of the wheel bearings.

The drive axle bolt may be loosened maximum 90° when the vehicle is standing on its wheels.

Vehicles without a drive axle must not be moved, otherwise the wheel bearing will be damaged. If a vehicle must be moved, be sure to note the following:

Install an outer joint in place of the drive axle.
Tighten the outer joint to 120 Nm.

-- Loosen the wheel bolts.

-- Raise the vehicle.

-- Remove the wheel.

-- Remove the brake caliper and tie it to the vehicle body with wire. Refer to Front Brake Caliper .

-- Disconnect the connector -1- from the ABS speed sensor.

Fig 1: Identifying Speed Sensor

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Remove the bolt -arrow- and the ABS speed sensor -1-.

Fig 2: Identifying Speed Sensor Bolts

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Remove the brake rotor -1- -arrow-.

Fig 3: Identifying Brake Rotor

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Remove the cover plate -1- from the wheel bearing housing -arrow-.

Fig 4: Identifying Cover Plate

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Loosen nut of track rod ball joint, but do not unscrew yet.

Fig 5: Identifying Nut Of Track Rod Ball Joint

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

CAUTION:

To protect thread, screw nut on pin a few turns.

-- Remove the tie rod from the wheel bearing housing and remove the nut.

Ball Joint PullerT10187

-- Loosen nuts -arrows-.

Fig 6: Identifying Nuts -Arrows- On Left And Right Side Of Vehicle, Removal

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Remove the control arm from the ball joint.

-- Remove the drive axle outer joint from the wheel hub.

If the Drive Axle Cannot be Pulled Out of the Wheel Bearing, Then it Can Be Pushed Out of the Wheel Bearing Using the RemoverT10520.

Before using the RemoverT10520 pay attention that the thrust piece -1- is installed.

Fig 7: Locating Thrust Piece

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

Using the RemoverT10520:

Fig 8: Identifying Remover T10520

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Secure the RemoverT10520 -1- with three wheel bolts -2- on the wheel hub, so that the drive axle -3- can be pressed out.

-- Follow the specified sequence.

Fig 9: Identifying Tightening Sequence

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

I -

Tighten the knurled nut -1- hand-tight.

II -

Turn only the bolt -2- with a wrench and press out the drive axle with the RemoverT10520.

NOTE:

At the end of the tasks or to set back, the spindles must be brought back into the original position so that the hydraulic operation can be used.

-- Secure drive axle to body using wire.

-- Move the Engine/Gearbox JackVAG1383A under the wheel bearing housing.

-- Remove threaded connection of wheel bearing housing/suspension strut -arrow-.

Fig 10: Identifying Threaded Connection Of Wheel Bearing Housing/Suspension Strut

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Insert Spreader Tool3424 into slot of wheel bearing housing.

Fig 11: Identifying 3424 Into Slot Of Wheel Bearing Housing

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Turn the ratchet 90° and remove it from the Spreader Tool3424.

-- Remove the wheel bearing housing from the suspension strut.

NOTE:

If the wheel bearing housing is being replaced, then the ball joint must also be replaced. Use new nuts.