Special Tools

Special tools and workshop equipment required 

• Slide Hammer-Complete Set VW771
• Additional Part for VW771VW771/37
• Puller T10408
• Thrust Piece T10408/2
• Plate T10408/3
• Adapter VW295 A
• Thrust Pad VW447 H
• Thrust Pad VW512
• Thrust Tube VW454
• Press Tube 2040
• Adapter 10-222 A/28
• Adapter 10-222 A /28-2
• Connecting Pin T10027 A
  Fig 1: Identifying Connecting Pin T10027 A

  
• Hose Clamp PliersVAG1275
  Fig 2: Hose Clamp Pliers V.A.G 1275

  
• Seal Installer Set - Rear Diff 3066
  Fig 3: Identifying Seal Installer Set

  
• Pin 3282/29
  Fig 4: Identifying Pin 3282/29

  
• Adjustment Plate 3282/39
  Fig 5: Identifying Adjusting Plate 3282/39

  
• Thrust Piece T10148
  Fig 6: Identifying Thrust Pad T10148

  
• Transmission Support Jig3336
  Fig 7: Identifying Transmission Support Jig. 3336

  
• Shop Crane - Load Cap = 700-1200 KGVAS 6100
  Fig 8: Identifying Shop Crane VAS 6100

  
• Press Piece - Block T10083
  Fig 9: Identifying Pressing Support T10083

  
• -2- Puller - Kukko Puller - 60-150mm Width, 200mm Length 18/1
  Fig 10: Identifying Kukko Tools

  
• Inductive Heat Unit VAS6414
  Fig 11: Identifying Inductive Heater VAS 6414

  
• Thrust Piece T10203
  Fig 12: Identifying Thrust Piece T10203

  
• Press Piece - Shift Rod/Alternator VW423
  Fig 13: Identifying Sleeve VW 423

  
• Assembly Mandrel 10-508
  Fig 14: Identifying Assembly Drift 10 - 508

  
• Spring Strut Compressor 2070
  Fig 15: Identifying Tensioning Device 2070

  
• Trim Removal Wedge 3409
  Fig 16: 3409 Wedge

  

Fig 17: Identifying Special Tools

Special tools and workshop equipment required 

• Engine Support Bridge 10-222 A
• Transmission Support 3282
• Engine-/Gearbox Jack VAG1383 A
• Tensioning Strap T10038
• Engine Support Basic Set T40091
• Engine Support Supplement Set T40093

Fig 18: Identifying Special Tools

Special tools and workshop equipment required 

• Holding Plate VW309
• Transmission Support VW353
• Needle Bearing Drift VW295
• Driving Sleeve VW244 B
• Hot Air Blower VAG1416
• Torque Wrench 1331 5-50Nm VAG1331

Fig 19: Identifying Special Service Tools

Special tools and workshop equipment required 

• Bracket - Multiple Use 30-211A
• Driving Sleeve 32-111
• Thrust Piece T10030/4 from Assembly Tool T10030
• Tube 37 mm Dia.VW416 B
• Puller T10309
• Two Arm Puller T10040
• Puller Legs with Thrust Piece T10040/2A+/3

Fig 20: Identifying Special Tools And Workshop Equipment

Special tools and workshop equipment required 

• Support Bridge T10323
• Subframe Support Assembling Device 3253/7
• Thrust Pad Con. 8/65VW433
• Torque Wrench 1332 40-200Nm VAG1332

Fig 21: Identifying Special Service Tools

Special tools and workshop equipment required 

• Press Plate VW402
• Subframe Support Assm. Device 3290
• Thrust Pad 16.5/28 mm Dia.VW431
• Assembly Tool 3301
• Spacer VW472/2
• Drift 10-206