Adapter For Assembling Flushing Circuit
WARNING: This page is about a different car, the 2016 Volkswagen Beetle, 2015 Volkswagen Beetle, 2014 Volkswagen Beetle, 2013 Volkswagen Beetle, and 2012 Volkswagen Beetle. However, it is still accessible from the selected car via links, so may be relevant.
- The following table lists the different adapters necessary to connect the service station to the refrigerant circuit, to flush and to bypass the removed receiver/dryer or reservoir and expansion valve (depending on the vehicle).
- Using a charge hose with 5/8 -18 UNF connections (short version, for example Refrigerant Circuits Adapter Set 1 - Hose 31 VAS 6338/31), connect the two adapters (contained in Refrigerant Circuits Adapter Set 1 VAS 6338/1) which have been installed for the removed reservoir or receiver/dryer.
- If a flushed refrigerant circuit is not reassembled immediately after flushing, adapters remain at connections and seal the connections at the adapters using Refrigerant Circuits Adapter Set 1 - Adapter 30 VAS 6338/30 (from Refrigerant Circuits Adapter Set 1 VAS 6338/1).
- Depending on the version of the A/C compressor and on the time period of production, various connecting and sealing technologies can be found on the refrigerant circuit.
Block or screw connections
Screw connection -A-
Block connection -B-
Block connections with different types of seals
Block connection with radially sealed connection -A- (with plastic or metal guide -B-)
-- Block connection with axial sealing connection -C-
Fox MY 2005
| Vehicle | Required adapters for refrigerant pipes to A/C compressor | Required adapters for refrigerant pipes to receiver/dryer | Miscellaneous |
|---|---|---|---|
| Fox from MY 2005 |
|
-- Remove dryer cartridge and seal receiver/dryer.-- Install a new dryer cartridge after flushing. | -- Replace the expansion valve with the Refrigerant Circuits Adapter Set 1 - Adapter 34 VAS 6338/34 (or a drilled open expansion valve GENERAL INFORMATION => )-- Install a new expansion valve after flushing. |
Lupo MY 1999
| Vehicle | Required adapters for refrigerant pipes to A/C compressor | Required adapters for refrigerant pipes to receiver/dryer | Miscellaneous |
|---|---|---|---|
| Lupo from MY 1999 through VIN 70000 |
|
-- Remove receiver/dryer and bridge coolant pipes.
|
-- Expansion valve replaced by Refrigerant Circuits Adapter Set 1 - Adapter 19 VAS 6338/19 (or a drilled open expansion valve for example 6N0 820 679 C GENERAL INFORMATION => )-- Install a new expansion valve after flushing. |
| Lupo from MY 1999 from VIN 70001 |
|
Receiver/Dryer-- May be flushed.-- Install a new receiver/dryer after flushing. | -- Replace the expansion valve with the Refrigerant Circuits Adapter Set 1 - Adapter 19 VAS 6338/19 (or a drilled open expansion valve, for example 6N0 820 679 C GENERAL INFORMATION => )-- Install a new expansion valve after flushing. |
up! 2012; e-up! MY 2014
| Vehicle | Required adapters for refrigerant pipes to A/C compressor | Required adapters for refrigerant pipes to receiver/dryer | Miscellaneous |
|---|---|---|---|
| up! e-up! from MY 2012 From MY 2014 |
|
Receiver/Dryer-- May be flushed.-- Install a new receiver/dryer after flushing. | -- Replace the expansion valve with the Refrigerant Circuits Adapter 36 VAS 6338/36 or Refrigerant Circuits Adapter Set 1 - Adapter 34 VAS 6338/34 (or a drilled open expansion valve, for example 1S0 820 078 GENERAL INFORMATION => )-- Install a new expansion valve after flushing. |
Polo MY 1995
| Vehicle | Required adapters for refrigerant pipes to A/C compressor | Required adapters for refrigerant pipes to receiver/dryer | Miscellaneous |
|---|---|---|---|
| Polo from MY 1995 through VIN 50000 | Refrigerant Circuits Adapter Set 1 - Adapter 14 VAS 6338/14 | -- Remove receiver/dryer and bridge coolant pipes.
|
-- Replace the expansion valve with the Refrigerant Circuits Adapter Set 1 - Adapter 19 VAS 6338/19 (or a drilled open expansion valve, for example 6N0 820 679 C GENERAL INFORMATION => )-- Install a new expansion valve after flushing. |
| Polo from MY 1995 from VIN 50001 |
|
Receiver/Dryer-- May be flushed.-- Install a new receiver/dryer after flushing. | -- Replace the expansion valve with the Refrigerant Circuits Adapter Set 1 - Adapter 19 VAS 6338/19 (or a drilled open expansion valve, for example 6N0 820 679 C GENERAL INFORMATION => )-- Install a new expansion valve after flushing. |
Polo MY 2002
| Vehicle | Required adapters for refrigerant pipes to A/C compressor | Required adapters for refrigerant pipes to receiver/dryer | Miscellaneous |
|---|---|---|---|
| Polo from MY 2002 |
|
-- Remove dryer cartridge and seal receiver/dryer.-- Install a new dryer cartridge after flushing. | -- Replace the expansion valve with the Refrigerant Circuits Adapter Set 1 - Adapter 34 VAS 6338/34 (or a drilled open expansion valve GENERAL INFORMATION => )-- Install a new expansion valve after flushing. |
Caddy MY 1996; Caddy MY 2004; Caddy MY 2011
| Vehicle | Required adapters for refrigerant pipes to A/C compressor | Required adapters for refrigerant pipes to receiver/dryer | Miscellaneous |
|---|---|---|---|
| Caddy from MY 1996 |
|
-- Remove receiver/dryer and bridge coolant pipes.
|
-- Replace the expansion valve with the Refrigerant Circuits Adapter Set 1 - Adapter 19 VAS 6338/19 (or a drilled open expansion valve, for example 6N0 820 679 C GENERAL INFORMATION => )-- Install a new expansion valve after flushing. |
| Caddy from MY 2004; Caddy from MY 2011 |
|
Receiver/Dryer-- May be flushed.-- Install a new receiver/dryer after flushing. | -- Replace the expansion valve with the Refrigerant Circuits Adapter Set 1 - Adapter 18 VAS 6338/18 (or a drilled open expansion valve GENERAL INFORMATION => )-- Install a new expansion valve after flushing. |
Polo 2010; Polo KH IN MY 2010; Polo KH IN MY 2015; Polo Lim IN MY 2011; Polo Lim RUS MY 2011; Polo KH MY 2014; Polo KH MY 2015; Polo Lim MY 2014; Polo MY 2014
| Vehicle | Required adapters for refrigerant pipes to A/C compressor | Required adapters for refrigerant pipes to receiver/dryer | Miscellaneous |
|---|---|---|---|
| Polo from MY 2010; Polo KH IN from MY 2010; Polo HH IN MY 2015; Polo Lim IN from MY 2011; Polo Lim RUS from MY 2011; Polo KH from MY 2014; Polo KH from MY 2015; Polo Lim from MY 2014; Polo from MY 2014 |
|
-- Remove dryer cartridge and seal receiver/dryer.-- Install a new dryer cartridge after flushing. | -- Replace the expansion valve with the Refrigerant Circuits Adapter Set 1 - Adapter 34 VAS 6338/34 (or a drilled open expansion valve GENERAL INFORMATION => )-- Install a new expansion valve after flushing. |
Golf MY 1992; Vento MY 1992; Passat MY 1994
| Vehicle | Required adapters for refrigerant pipes to A/C compressor | Required adapters for refrigerant pipes to receiver/dryer | Miscellaneous |
|---|---|---|---|
| Golf from MY 1992; Vento from MY 1992; Passat from MY 1994 | Refrigerant Circuits Adapter Set 1 - Adapter 14 VAS 6338/14 | -- Remove receiver/dryer and bridge coolant pipes.
|
-- Replace the expansion valve with the Refrigerant Circuits Adapter Set 1 - Adapter 19 VAS 6338/19 (or a drilled open expansion valve, for example 6N0 820 679 C GENERAL INFORMATION => )-- Install a new expansion valve after flushing. |
Touareg MY 2003; Golf MY 2004; Golf Plus MY 2005; Golf Plus MY 2009; Jetta MY 2005; Eos MY 2006; Golf Variant MY 2007; Tiguan MY 2008; Scirocco MY 2009; Scirocco MY 2015; Golf MY 2009; Golf Variant MY 2010; Jetta MY 2011; Golf Cabrio MY 2012; NMS MY 2012; Beetle MY 2012 and Golf MY 2013
| Vehicle | Required adapters for refrigerant pipes to A/C compressor | Required adapters for refrigerant pipes to receiver/dryer | Miscellaneous |
|---|---|---|---|
| Touran from MY 2003; Golf from MY 2004; Golf Plus from MY 2005; Golf Plus from MY 2009; Jetta from MY 2005; Eos from MY 2006; Golf Variant from MY 2007; Tiguan from MY 2008; Scirocco from MY 2009; Scirocco from MY 2015; Golf from MY 2009; Golf Variant from MY 2010; Jetta from MY 2011; Golf Cabrio from MY 2012; NMS from MY 2012 and Beetle from MY 2012 |
|
There are two versions of the receiver/dryer: Refer to the vehicle specific Repair Information.
|
-- Replace the expansion valve with the Refrigerant Circuits Adapter Set 1 - Adapter 18 VAS 6338/18 (or a drilled open expansion valve GENERAL INFORMATION => )-- Install a new expansion valve after flushing. |
Golf MY 2013; Golf Wagon MY 2014; Golf MY 2014 (USA and Canada); Golf Sportsvan MY 2015
| Vehicle | Required adapters for refrigerant pipes to A/C compressor | Required adapters for refrigerant pipes to receiver/dryer | Miscellaneous |
|---|---|---|---|
| Golf from MY 2013; Golf Wagon from MY 2014; Golf from MY 2014 (USA and Canada); Golf Sportsvan from MY 2015 |
|
-- Remove the dryer bag / cartridge and close the receiver/dryer.-- Install a new dryer bag / cartridge after flushing.-- If the condenser by Showa is installed, leave the receiver/dryer installed and flush the refrigerant circuit. -- Install a new receiver/dryer after flushing. | -- Replace the expansion valve with the Refrigerant Circuits Adapter Set 1 - Adapter 38 VAS 6338/38 (or a drilled open expansion valve GENERAL INFORMATION => )-- Install a new expansion valve after flushing. |
Golf MY 1998; Golf Wagon MY 1998; Vento MY 1999; New Beetle MY 1999; New Beetle Cabrio MY 2003; Bora MY 1999;
| Golf from MY 1998; Golf Wagon from MY 1998; Vento from MY 1999; New Beetle from MY 1999; New Beetle Convertible from MY 2003; Bora from MY 1999 |
|
-- Remove receiver/dryer and bridge coolant pipes.-- Connect with two Refrigerant Circuits Adapter Set 1 - Adapter 2 VAS 6338/2 and with Refrigerant Circuits Adapter Set 1 - Hose 31 VAS 6338/31.-- Install a new receiver/dryer after flushing. | -- Replace the expansion valve with the Refrigerant Circuits Adapter Set 1 - Adapter 19 VAS 6338/19 (or a drilled open expansion valve GENERAL INFORMATION => )-- Install a new expansion valve after flushing. |
Phaeton MY 2003
| Vehicle | Required adapters for refrigerant pipes to A/C compressor | Required adapters for refrigerant pipes to receiver/dryer/reservoir | Miscellaneous |
|---|---|---|---|
| Phaeton from MY 2003 |
|
-- Remove the reservoir (dryer) and bridge coolant pipes.-- Connect with two Refrigerant Circuits Adapter Set 1 - Adapter 6 VAS 6338/6 and with Refrigerant Circuits Adapter Set 1 - Hose 31 VAS 6338/31.-- Install a new reservoir after flushing. | -- Restrictor removed and refrigerant pipe reconnected.-- Install a new restrictor after flushing. |
Passat MY 1997
| Vehicle | Required adapters for refrigerant pipes to A/C compressor | Required adapters for refrigerant pipes to receiver/dryer/reservoir | Miscellaneous |
|---|---|---|---|
| Passat from MY 1997 through 09/2000 |
|
There are two different container versions.-- Remove reservoir and bridge coolant pipes.-- Connect Refrigerant Circuits Adapter Set 1 - Adapter 9 VAS 6338/9 and Refrigerant Circuits Adapter Set 1 - Adapter 8 VAG 1785/8 or Refrigerant Circuits Adapter Set 1 - Adapter 10 VAS 6338/10 with Refrigerant Circuits Adapter Set 1 - Hose 31 VAS 6338/31.-- Install a new reservoir after flushing. | -- Restrictor removed and refrigerant line reconnected.-- Install a new restrictor after flushing. |
| Passat from MY 1997, from 10/2000 |
|
-- Remove reservoir and bridge coolant pipes.-- Connect with two Refrigerant Circuits Adapter Set 1 - Adapter 10 VAS 6338/10 and with Refrigerant Circuits Adapter Set 1 - Hose 31 VAS 6338/31.-- Install a new reservoir after flushing. | -- Restrictor removed and refrigerant line reconnected.-- Install a new restrictor after flushing. |
Passat MY 2006; Passat CC MY 2009; CC MY 2010; Passat MY 2011; CC FL
| Vehicle | Required adapters for refrigerant pipes to A/C compressor | Required adapters for refrigerant pipes to receiver/dryer/reservoir | Miscellaneous |
|---|---|---|---|
| Passat from MY 2006; Passat CC from MY 2009; CC from MY 2010; Passat from MY 2011; CC FL |
|
-- Remove dryer cartridge and seal receiver/dryer.-- Install a new dryer cartridge after flushing.-- If the condenser by Showa is installed, leave the receiver/dryer installed and flush the refrigerant circuit. -- Install a new receiver/dryer after flushing. | -- Replace the expansion valve with the Refrigerant Circuits Adapter Set 1 - Adapter 18 VAS 6338/18 (or a drilled open expansion valve GENERAL INFORMATION => )-- Install a new expansion valve after flushing. |
Passat MY 2015; Passat Wagon MY 2015
NOTE:
The Passat 2015 and Passat Wagon 2015 with a Biturbo engine are not flushed. The amount of work to remove the expansion valve is too excessive. If there is A/C compressor damage, check whether there are shavings in the condenser and whether there are shavings on the condenser output. If there are shavings on the input and not on the output, then only the condenser and A/C Compressor need to be replaced.
| Vehicle | Required adapters for refrigerant pipes to A/C compressor | Required adapters for refrigerant pipes to receiver/dryer | Miscellaneous |
|---|---|---|---|
| Passat from MY 2015; Passat Wagon from MY 2015 |
|
-- Remove the dryer bag / cartridge and close the receiver/dryer.-- Install a new dryer bag / cartridge after flushing. | -- Replace the expansion valve with the Refrigerant Circuits Adapter Set 1 - Adapter 18 VAS 6338/18 (or a drilled open expansion valve GENERAL INFORMATION => )-- Install a new expansion valve after flushing. |
Sharan MY 1996
NOTE:
On vehicles with second evaporator (Sharan), the front and rear refrigerant circuits must be flushed individually. Seal the front refrigerant circuit using A/C Adapter Set - Adapter 1 VAG 1785/1, A/C Adapter Set - Adapter 31785/3 and Closure Caps VAS 6338/30.
| Vehicle | Required adapters for refrigerant pipes to A/C compressor | Required adapters for refrigerant pipes to receiver/dryer and second Evaporator | Miscellaneous |
|---|---|---|---|
| Sharan from MY 1996 through 05/2000 |
|
-- Remove the receiver/dryer and connect the refrigerant pipes to the Refrigerant Circuits Adapter Set 1 - Adapter 37 VAS 6338/37-- Install a new receiver/dryer (dryer) after flushing.
|
-- Replace the front and rear expansion valve with the Refrigerant Circuits Adapter Set 2 - Adapter 35 VAS 6338/35 (or a drilled open expansion valve GENERAL INFORMATION => )-- Install a new expansion valve after flushing. |
| Sharan from MY 1996 from June 2000 |
|
-- Remove dryer cartridge and seal receiver/dryer.-- Install a new dryer cartridge after flushing.
|
-- Replace the front and rear expansion valve with the Refrigerant Circuits Adapter Set 2 - Adapter 35 VAS 6338/35 (or a drilled open expansion valve GENERAL INFORMATION => )-- Install a new expansion valve after flushing. |
Sharan MY 2011
NOTE:
On vehicles with second evaporator (Sharan), the front and rear refrigerant circuits must be flushed individually. Seal the front refrigerant circuit using A/C Adapter Set - Adapter 1 VAG 1785/1, A/C Adapter Set - Adapter 31785/3 and Closure Caps VAS 6338/30.
| Vehicle | Required adapters for refrigerant pipes to A/C compressor | Required adapters for refrigerant pipes to receiver/dryer and second Evaporator | Miscellaneous |
|---|---|---|---|
| Sharan from MY 2011 |
|
-- Remove dryer cartridge and seal receiver/dryer.-- Install a new dryer cartridge after flushing.
|
-- Replace the front expansion valve with the Refrigerant Circuits Adapter Set 1 - Adapter 18 VAS 6338/18 (or a drilled open expansion valve GENERAL INFORMATION => )-- Replace the rear expansion valve with the Refrigerant Circuits Adapter Set 2 - Adapter 33 VAS 6338/33 (or a drilled open expansion valve GENERAL INFORMATION => )-- Install a new expansion valve after flushing. |
Touareg MY 2003; Touareg MY 2010; Touareg MY 2015; Touareg MY Hybrid 2010
NOTE:
On vehicles with second evaporator (Touareg), the front and rear refrigerant circuits must be flushed individually. Seal the front refrigerant circuit using Refrigerant Circuits Adapter Set 1 - Adapter 5 VAS 6338/5 and Refrigerant Circuits Adapter Set 1 - Adapter 11 VAS 6338/11.
| Vehicle | Required adapters for refrigerant pipes to A/C compressor | Required adapters for refrigerant pipes to receiver/dryer and second Evaporator | Miscellaneous |
|---|---|---|---|
| Touareg from MY 2003 through VIN 50000 |
|
-- Remove dryer cartridge and seal receiver/dryer.-- Install a new dryer cartridge after flushing.
|
-- Replace the front expansion valve with the Refrigerant Circuits Adapter Set 1 - Adapter 17 VAS 6338/17 (or a drilled open expansion valve GENERAL INFORMATION => )-- Install a new expansion valve after flushing.-- Drill a hole for the expansion valve on the second evaporator GENERAL INFORMATION => .-- Install a new expansion valve after flushing. |
| Touareg from MY 2003 from VIN 50001; Touareg from MY 2010; Touareg MY 2015; Touareg Hybrid from MY 2010 |
|
-- Remove dryer cartridge and seal receiver/dryer.-- Install a new dryer cartridge after flushing.
|
-- Replace the front and rear expansion valve with the Refrigerant Circuits Adapter Set 1 - Adapter 17 VAS 6338/17 or Refrigerant Circuits Adapter Set 2 - Adapter 33 VAS 6338/33 (or a drilled open expansion valve GENERAL INFORMATION => )-- Install new expansion valves after flushing. |
Transporter MY 1991
NOTE:
On vehicles with second evaporator, the front and rear refrigerant circuits must be flushed individually. Seal the front refrigerant circuit using Refrigerant Circuits Adapter Set 1 - Adapter 5 VAS 6338/5 and Refrigerant Circuits Adapter Set 1 - Adapter 11 VAS 6338/11.
| Vehicle | Required adapters for refrigerant pipes to A/C compressor | Required adapters for refrigerant pipes to receiver/dryer and second Evaporator | Miscellaneous |
|---|---|---|---|
| Transporter from MY 1991 through 2012 1995 |
|
|
-- Replace the front and rear expansion valve with the Refrigerant Circuits Adapter Set 2 - Adapter 55 VAS 6338/55 (or a drilled open expansion valve GENERAL INFORMATION => )-- Install a new expansion valve after flushing. |
| Transporter from MY 91 as of 01 1996 |
|
|
-- Replace the front and rear expansion valve with the Refrigerant Circuits Adapter Set 2 - Adapter 55 VAS 6338/55 (or a drilled open expansion valve GENERAL INFORMATION => )-- Install a new expansion valve after flushing. |
Transporter MY 2004
NOTE:
On vehicles with second evaporator, the front and rear refrigerant circuits must be flushed individually. Seal the front refrigerant circuit using Refrigerant Circuits Adapter Set 1 - Adapter 5 VAS 6338/5 and Refrigerant Circuits Adapter Set 1 - Adapter 11 VAS 6338/11.
| Vehicle | Required adapters for refrigerant pipes to A/C compressor | Required adapters for refrigerant pipes to receiver/dryer and second Evaporator | Miscellaneous |
|---|---|---|---|
| Transporter 7H from MY 2004 |
|
-- Remove dryer cartridge and seal receiver/dryer.-- Install a new dryer cartridge after flushing.
|
-- Through VIN 20000, drill out the expansion valve GENERAL INFORMATION => .-- From VIN 20001, replace the front expansion valve with Refrigerant Circuits Adapter Set 2 - Adapter 56 VAS 6338/56-- Install a new expansion valve after flushing.-- Drill a hole for the expansion valve Replace the evaporator with Refrigerant Circuits Adapter Set 2 - Adapter 33 VAS 6338/33.-- Install a new expansion valve after flushing. |
| Transporter 7J from MY 2004 |
|
-- Remove dryer cartridge and seal receiver/dryer.-- Install a new dryer cartridge after flushing.
|
-- Through VIN 5000, drill out the expansion valve GENERAL INFORMATION => .-- From VIN 5001, replace the front expansion valve with Refrigerant Circuits Adapter Set 2 - Adapter 56 VAS 6338/56.-- Install a new expansion valve after flushing.-- Drill a hole for the expansion valve Replace the evaporator with Refrigerant Circuits Adapter Set 2 - Adapter 56 VAS 6338/56.-- Install a new expansion valve after flushing. |
Transporter MY 2010; Multivan MY 2010; California MY 2010; Caravelle MY 2010
NOTE:
On vehicles with second evaporator, the front and rear refrigerant circuits must be flushed individually. Seal the front refrigerant circuit using Refrigerant Circuits Adapter Set 1 - Adapter 5 VAS 6338/5 and Refrigerant Circuits Adapter Set 1 - Adapter 11 VAS 6338/11.
| Vehicle | Required adapters for refrigerant pipes to A/C compressor | Required adapters for refrigerant pipes to receiver/dryer and second Evaporator | Miscellaneous |
|---|---|---|---|
| Transporter from MY 2010; Multivan from MY 2010; California from MY 2010; Caravelle from MY 2010 |
|
-- Remove dryer cartridge and seal receiver/dryer.-- Install a new dryer cartridge after flushing.
|
-- Replace the expansion valve with the Refrigerant Circuits Adapter Set 2 - Adapter 56 VAS 6338/56 (or a drilled open expansion valve GENERAL INFORMATION => )-- Remove the expansion valve for the rear evaporator and drill open GENERAL INFORMATION => .-- Install a new expansion valve after flushing. |
Crafter 2006; LT 2 from MY 1997
NOTE:
On vehicles with second evaporator, the front and rear refrigerant circuits must be flushed individually. Seal the front refrigerant circuit using Refrigerant Circuits Adapter Set 1 - Adapter 5 VAS 6338/5 and Refrigerant Circuits Adapter Set 1 - Adapter 11 VAS 6338/11.
| Vehicle | Required adapters for refrigerant pipes to A/C compressor | Required adapters for refrigerant pipes to receiver/dryer and second Evaporator | Miscellaneous |
|---|---|---|---|
| Crafter from MY 2006 |
|
Receiver/Dryer-- May be flushed.-- Install a new receiver/dryer after flushing.
|
-- Drill a hole for the expansion valve GENERAL INFORMATION => -- Install a new expansion valve after flushing. |
| LT 2 from MY 1997 |
|
-- Remove receiver/dryer and bridge coolant pipes.-- Connect with two Refrigerant Circuits Adapter Set 1 - Adapter 29 VAS 6338/10 and with Refrigerant Circuits Adapter Set 1 - Hose 31 VAS 6338/31.-- Install a new receiver/dryer after flushing. | -- Replace the expansion valve with the Refrigerant Circuits Adapter Set 2 - Adapter 56 VAS 6338/56 (or a drilled open expansion valve GENERAL INFORMATION => )-- Install a new expansion valve after flushing. |
Amarok MY 2011
| Vehicle | Required adapters for refrigerant pipes to A/C compressor | Required adapters for refrigerant pipes to receiver/dryer | Miscellaneous |
|---|---|---|---|
| Amarok from MY 2011 |
|
-- Remove dryer cartridge and seal receiver/dryer.-- Install a new dryer cartridge after flushing., | -- Replace the expansion valve with the Refrigerant Circuits Adapter Set 2 - Adapter 33 VAS 6338/33 (or a drilled open expansion valve GENERAL INFORMATION => ) |
Golf blue e-Motion MY 2009
| Vehicle | Required adapters for refrigerant pipes to A/C compressor and on A/C compressor | Required adapters for refrigerant pipes to receiver/dryer | Miscellaneous |
|---|---|---|---|
| Golf blue e-Motion from MY 2009 |
|
-- Remove dryer cartridge and seal receiver/dryer.-- Install a new dryer cartridge after flushing.
|
-- Replace the expansion valve with the Refrigerant Circuits Adapter Set 1 - Adapter 34 VAS 6338/34 (or a drilled open expansion valve GENERAL INFORMATION => )-- Install a new expansion valve after flushing.-- Remove the High Voltage Battery Heater Core Refrigerant Cut-Off Valve -N542- and install the Refrigerant Circuits Adapter Set - Shut-Off Valve VAS 6338/42.-- Remove the Heater and A/C Unit Refrigerant Cut-Off Valve -N541- and install the Refrigerant Circuits Adapter Set - Shut-Off Valve VAS 6338/42. Note Warnings ADAPTER FOR ASSEMBLING FLUSHING CIRCUIT => -- If the Refrigerant Circuits Adapter Set - Shut-Off Valve VAS 6338/42 is not available, a voltage of 12 V can be applied to the Cut-Off Valves -N541- and -N542-. |
eGolf MY 2014 and eGolf MY 2014 with Heat Pump
| Vehicle | Required adapters for refrigerant pipes to A/C compressor and on A/C compressor | Required adapters for refrigerant pipes to receiver/dryer | Miscellaneous |
|---|---|---|---|
| e-Golf from MY 2014 |
|
-- Remove dryer cartridge and seal receiver/dryer.-- Install a new dryer cartridge after flushing. | -- Replace the expansion valve with the Refrigerant Circuits Adapter Set 1 - Adapter 34 VAS 6338/34 (or a drilled open expansion valve GENERAL INFORMATION => )-- Install a new expansion valve after flushing. |
| eGolf from MY 2014 with Heat Pump |
|
-- Remove the reservoir (dryer) and bridge coolant pipes.-- Connect with two Refrigerant Circuits Adapter Set 1 - Adapter 6 VAS 6338/6 and with Refrigerant Circuits Adapter Set 1 - Hose 31 VAS 6338/31.-- Install a new reservoir after flushing. | -- Using the =>
, then start the "Refrigerant circuit, charging" function in the "Basic setting".
|
Golf Hybrid MY 2014
| Vehicle | Required adapters for refrigerant pipes to A/C compressor and on A/C compressor | Required adapters for refrigerant pipes to receiver/dryer | Miscellaneous |
|---|---|---|---|
| Golf Hybrid from MY 2014 |
|
There are two versions of the receiver/dryer: Refer to the vehicle specific Repair Information.
|
|