Output Shaft

WARNING: This page is about a different car, the 2013 Volkswagen Beetle. However, it is still accessible from the selected car via links, so may be relevant.

Special tools and workshop equipment required

PunchVW407
Press Piece - Multiple UseVW412
Thrust PadVW512
Tapered Roller Bearing PullerVAG1582
Attachment to VAG 1582V.A.G 1582/4
Attachment to VAG 1582V.A.G 1582/5
Press PlateVW402
Driving Sleeve32-111
PunchVW408 A
PunchVW409
Support Channels VW457
Sleeve VW519
Thrust Ring VW429
Tube 60 mm Dia.VW415 A
Thrust Pad VW447 H
Thrust Tube VW454
Thrust Tube VW455
Mounting Universal Joint41-501
Kukko Extractor 37-46 mm Kukko 21/6
Kukko Separating Tool 22-115 mm17/2
Puller - Kukko Counterstay 22/2
Hot Air BlowerV.A.G. 1416

Fig 1: Identifying Small Outer Race/Tapered Roller Bearing

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

A -

Internal puller 37 to 46 mm, for example, Kukko extractor 37-46 mm21/6

B -

Counter support, for example, Puller - Kukko Counterstay22/2

Fig 2: Identifying Small Outer Race/Tapered Roller Bearing

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

Fig 3: Identifying Small Inner Race/Tapered Roller Bearing

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

A -

Protective jaws for the vise.

-- Mount the grip and apply tension behind rolling the bearing. Then rotate the bearing and apply tension to the grip.

Fig 4: Identifying Small Tapered Roller Bearing Inner Race

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

Fig 5: Identifying 3rd And 4th Gear Synchro-Hub/Locking Collar, 2nd, 3rd And 4th Gears With Transmission Housing Needle Roller Bearing Sleeve

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

A -

Separating tool 22 to 115 mm, for example, Kukko separating tool 22-115 mm17/2

B -

M10 x 20, 17 mm bolt

NOTE:

Support the separating tool to prevent the 1st/2nd gear locking collar from coming off too.

Fig 6: Identifying Locking Collar With Synchronizer Hub And Bearing Mount

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Remove the lock ring -arrow- beforehand.

Fig 7: Identifying Large Inner Race/Tapered Roller Bearing

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-A- : Protective jaws for the vise.

-- Before installing the puller, insert a M10 x 20 bolt in the bore of the output shaft.

Fig 8: Identifying Inner Race Of Large Taper Roller Bearing

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-A- thrust washer

-- Install the thrust washer before installing the bearing inner race. The shoulder faces the inner race.

Fig 9: Exploded View Of Modified 1st Gear Synchronization Components (From Transmission Build Date 02 05 0)

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Place the inner race -A- on the drive gear for 1st gear.

The angled tabs -arrows 1- face the outer race -B-.

-- Install the outer race -B-.

The tabs -arrows 2- must lock into the retainers -arrows 3- in the gear.

-- Install the synchronizer ring -C-.

The retainers -arrows 4- lock in the tabs -arrows 1- on the inner race -A-.

NOTE:

If the parts are not to be replaced, make sure they are installed in their original gear location.

Fig 10: Checking 1St, 2Nd And 3Rd Gear Inner Ring For Wear

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Install the inner race onto the taper of the selector gear and then measure the gap dimension -a- with a feeler gauge.

Gap dimension -a-	Installed dimension	Wear limit
1st and 2nd gear	0.75 to 1.25 mm	0.3 mm

Fig 11: Checking 1St, 2Nd And 3Rd Gear Synchro-Rings For Wear

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Install the synchronizer ring, outer race and inner race onto the taper of the selector gear and then measure the gap dimension -a- with a feeler gauge.

Gap dimension -a-	Installed dimension	Wear limit
1st and 2nd gear	1.2 to 1.8 mm	0.5 mm

Fig 12: Identifying Locking Collar And Locking Pieces With 1st And 2nd Gear Synchro-Hub Components

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

1 - Spring

For the correct spring, refer to the Parts Information.

Assembly in conjunction with hollow locking pieces, refer to Fig 13.

Assembly in conjunction with locking pieces that are not hollow, refer to Fig 14.

2 - Locking collar

3 - Synchronizer hub

4 - Locking piece

For the correct locking pieces, refer to the Parts Information.

The collar has the same width on both sides of the synchronizer hub.

The shoulder has a chamfer on one side -arrow B-

The bevel on the synchronizer hub collar and the splines on the outside of the locking collar -arrow A- face in the same direction after being assembled.

The notches on the synchronizer hub and locking collar for the locking pieces -arrow C- must line up.

Fig 13: Assembling 1st And 2nd Gear Locking Collar/Synchro-Hub

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

The locking collar is pushed over the synchronizer hub.

-- Install the locking pieces and springs offset by 120°. The angled end of the spring must engage into the hollow locking piece.

Fig 14: Assembling Locking Collar/Synchronizer Hub Of 1st And 2nd Gear In Conjunction With Locking Pieces That Are Not Hollow

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

The locking collar is pushed over the synchronizer hub.

-- Install the locking pieces and springs offset by 120°. The angled end of the spring must be positioned in front of the locking pieces -arrows-.

Fig 15: Identifying Installation Position Of Locking Collar/Synchro-Hub 1st And 2nd Gear

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

The teeth of the locking collar -arrow- point toward the splines of the 3rd/4th gear synchronizer hub -A-.

Fig 16: Identifying Locking Collar/Synchronizer Hub For 1st And 2nd Gear

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

WARNING:

Wear safety gloves.

Turn the synchronizer ring so that the grooves line up with the locking pieces.

Fig 17: Identifying 1st Gear Outer-Ring Lugs

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

The tabs -arrows- face 1st gear -A-.

Fig 18: Identifying Synchro-Ring Lugs & Recesses

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

The tabs -arrow 1- engage into the holes -arrow 2- inside the synchronizer ring -B-.

Fig 19: Identifying 2nd Gear Shoulder & Lugs

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

The higher collar -A- faces toward 1st gear -B-. The notches in the collar -arrow- lock into the tabs on the outer race, refer to Fig 17.

Fig 20: Identifying Inner Race For 3rd Gear Needle Bearing

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

Fig 21: Checking 4Th Gear Synchro-Ring For Wear

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Press the synchronizer ring onto the taper of the gear and measure gap dimension -a- using a feeler gauge.

Gap dimension -a-	Installed dimension	Wear limit
3rd and 4th gear	1.0 to 1.7 mm	0.5 mm

Fig 22: Disassembling And Assembling 1St And 2Nd As Well As 3Rd And 4Th Gear Locking Collar And Synchro-Hub

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

1 - Spring

For the correct spring, refer to the Parts Information.

Assembly in conjunction with hollow locking pieces, refer to Fig 23.

Assembly in conjunction with locking pieces that are not hollow, refer to Fig 24.

2 - Locking piece

For the correct locking pieces, refer to the Parts Information.

3 - Locking collar

4 - Synchronizer hub

-- Slide the locking collar over the synchronizer hub.

The notches for the locking pieces on the synchronizer hub and locking collar must line up with each other.

Fig 23: Assembling 1St And 2Nd As Well As 3Rd And 4Th Gear Locking Collar/Synchro-Hub

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

The locking collar is pushed over the synchronizer hub.

-- Install the locking pieces and springs offset by 120°. The angled end of the spring must engage into the hollow locking piece.

Fig 24: Assembling Locking Collar/Synchronizer Hub Of 3rd And 4th Gear In Conjunction With Locking Pieces That Are Not Hollow

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

The locking collar is pushed over the synchronizer hub.

-- Install the locking pieces and springs offset by 120°. The angled end of the spring must be positioned in front of the locking pieces -arrows-.

Fig 25: Identifying 3rd And 4th Gear Locking Collar/Synchro-Hub Chamfer

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

The bevel -arrow- faces 4th gear.

Fig 26: Identifying 3rd And 4th Gear Synchro-Hub With Locking Collar And Special Tools VW412, VW519, VW402 & VW447H

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

WARNING:

Wear safety gloves.

Fig 27: Identifying Sleeve For 4th Gear Needle Bearing

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

Fig 28: Identifying Sleeve For Output Shaft Needle Bearing

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.