ABS Control Module -J104- AND ABS Hydraulic Unit -N55- WITH 4-CYLINDER DIESEL ENGINE AND ABS MARK 60 EC ABS/EDL/ASR/ESP: Removing

WARNING: This page is about a different car, the 2016 Volkswagen Beetle, 2015 Volkswagen Beetle, 2014 Volkswagen Beetle, and 2013 Volkswagen Beetle. However, it is still accessible from the selected car via links, so may be relevant.

Fig 1: Configuration

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

Installed location:

The ABS Control Module -J104- is attached to the ABS Hydraulic Unit -N55- and is located inside the engine compartment on the right side.

ABS Hydraulic Unit -N55- with ABS Control Module -J104-
Brake booster with tandem brake master cylinder

WARNING: Do not bend the brake lines near the ABS Hydraulic Unit -N55- !

Use the Vehicle Diagnostic Tester.

Chassis
Brake System
Anti-Lock Braking System Anti-lock Brake System (ABS)/EDL/ASR/ESP Mark 60 EC
Function
Check Coding in the Anti-lock Brake System (ABS) control module J104

NOTE: To perform work sequence, the ground cable must be disconnected from battery. Check if a coded radio is installed. If so, obtain anti-theft coding beforehand.

CAUTION: Danger of causing damage to electronic components when disconnecting the battery.

Observe the steps for disconnecting the battery.

-- Remove the noise insulation. Refer to REMOVAL AND INSTALLATION .

-- Remove engine cover near -arrows-.

Fig 2: Engine Cover

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Observe the given sequence -1 through 4-.

-- Reach as far as possible under the engine cover.

CAUTION: The bracket for attaching the engine cover to the cylinder head could break if removed incorrectly. Always follow these steps to remove the engine cover.

-- Remove the nuts -arrows- and then remove the heat shield -1- from the diesel particulate filter.

Fig 3: Locating Heat Shield Nuts

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Open the clips -arrows- and remove the upper toothed belt cover.

Fig 4: Removing Upper Toothed Belt Guard

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Release and remove connectors -1- through -3-.

Fig 5: Disconnect The Black

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Remove the particulate filter mount bolts -1-.

Fig 6: Identifying Particulate Filter Bracket Bolt

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Loosen the clamps and remove the hoses from the particulate filter. Refer to [For engine(s) CPRA, CPKA, CPLA, CPPA] Description and Operation [For engine(s) CVCA] Description and Operation [For engine(s) CCTA, CBFA] Description and Operation [For engine(s) CBUA] Description and Operation [For transmission(s) 02E, 02Q] [For engine(s) CVCA, CJAA] Description and Operation .

-- Raise the vehicle.

-- Loosen the clamp -1- for the turbocharger/particulate filter connection and remove it.

Fig 7: Identifying Turbocharger/Particulate Filter Clamp

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

NOTE: The illustration shows the clamp bolt -1- from underneath. This can also be installed from above in some cases.

Vehicles with Absorption Catalytic Converter

-- Disconnect the exhaust system between the particulate filter and the absorption catalytic converter. Refer to [For engine(s) CPRA, CPKA, CPLA, CPPA] Description and Operation [For engine(s) CVCA] Description and Operation [For engine(s) CCTA, CBFA] Description and Operation [For engine(s) CBUA] Description and Operation [For transmission(s) 02E, 02Q] [For engine(s) CVCA, CJAA] Description and Operation .

-- Disconnect the exhaust system after the absorption catalytic converter. Refer to [For engine(s) CPRA, CPKA, CPLA, CPPA] Description and Operation [For engine(s) CVCA] Description and Operation [For engine(s) CCTA, CBFA] Description and Operation [For engine(s) CBUA] Description and Operation [For transmission(s) 02E, 02Q] [For engine(s) CVCA, CJAA] Description and Operation .

Continuation for All Vehicles

-- If equipped, remove the EGR pipe from the particulate filter. Refer to [For engine(s) CPRA, CPKA, CPLA, CPPA] Description and Operation [For engine(s) CVCA] Description and Operation [For engine(s) CCTA, CBFA] Description and Operation [For engine(s) CBUA] Description and Operation [For transmission(s) 02E, 02Q] [For engine(s) CVCA, CJAA] Description and Operation .

-- Disconnect the exhaust system. Refer to [For engine(s) CPRA, CPKA, CPLA, CPPA] Description and Operation [For engine(s) CVCA] Description and Operation [For engine(s) CCTA, CBFA] Description and Operation [For engine(s) CBUA] Description and Operation [For transmission(s) 02E, 02Q] [For engine(s) CVCA, CJAA] Description and Operation .

-- Remove the exhaust system bracket from the subframe -arrows-.

Fig 8: Heat Shield Bolts

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Remove the bolts -1- and remove the drive shaft cover -2-.

Fig 9: Identifying Bolts And Drive Axle Cover

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Remove the right driveshaft form the flange, lay it down and secure it. Refer to REMOVAL AND INSTALLATION .

-- Remove the nuts -1-.

Fig 10: Identifying Nuts And Particulate Filter Bracket

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Remove the nuts -2- using the Wrench - Sw13 T10384.

-- Remove bracket for particulate filter -3-.

-- Close all openings using the Engine Bung Set VAS6122.

-- Lower the particulate filter just enough so that it touches the steering gear.

NOTE: Pay attention to the Exhaust Gas Temperature Sensor -- and the Heated Oxygen Sensor -- when lowering onto the cables in order to avoid any damage.

-- Remove the nuts -1- and remove the heat shield -2-, if equipped.

Fig 11: Identifying Nuts And Heat Shield

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Disconnect the connector from the ABS Control Module -J104- in direction of -arrow-.

Fig 12: Identifying Direction To Release And Remove Connector From Control Module

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Install the Brake Pedal Actuator VAG1869/2.

Fig 13: Identifying Brake Pedal Depressor V.A.G 1869/2

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Remove front left caps -1-.

Fig 14: Identifying Bleeder Screw Cap

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Remove rear left caps -1-.

Fig 15: Identifying Vent Screw Cap

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

Use suitable bleeder hose. It must fit tightly on bleeder valve so that no air gets into brake system.

-- Attach the bleeder bottle bleed hose -1- to the left front brake caliper bleed valve.

Fig 16: Identifying Bleed Valve

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Open the bleed valve.

-- Attach the bleeder bottle bleed hose -1- to the brake caliper bleed valve/left rear brake cylinder.

Fig 17: Identifying Bleed Valve

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Open the bleed valve.

-- Push the brake pedal with the Brake Pedal Actuator VAG1869/2 at least 60 mm.

-- Close left front and left rear bleeder valves.

Do not remove the Brake Pedal Actuator VAG1869/2.

-- Place a lint-free cloth under the ABS Control Module -J104- and the ABS Hydraulic Unit -N55-.

Make sure no brake fluid gets onto contacts.

CAUTION: Do not confuse the brake lines when connecting them to the ABS Hydraulic Unit -N55-. Mark the lines in their installed position before removing them.

-- First, mark both brake lines from master cylinder -A- and -B-.

Fig 18: Identifying Brake Lines (Brake Caliper) And Brake Lines (Master Cylinder)

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Remove the brake lines -A- and -B- from the ABS Hydraulic Unit -N55-.

-- Close the brake lines and threaded holes immediately using Plugs 1H0 698 311 A.

-- Mark brake lines -1- through -4- and then remove them.

-- Close the brake lines and threaded holes immediately using Plugs 1H0 698 311 A.

-- Remove the hex bolt form the bracket -arrow-.

-- Remove the ABS Hydraulic Unit -N55- with the ABS Control Module -J104- and the bracket sideways in direction of -arrow- from the rubber bushings on the console.

-- Turn the ABS Hydraulic Unit -N55- with the ABS Control Module -J104- upside down.

-- Remove the bracket. Refer to -item 15- from the ABS Hydraulic Unit -N55- inside the engine compartment.

-- Remove the ABS Hydraulic Unit -N55- with the ABS Control Module -J104-.