Overview - Assembly Mounts: Notes

WARNING: This page is about a different car, the 2017 Volkswagen GTI, 2016 Volkswagen GTI, 2015 Volkswagen Golf, and 2015 Volkswagen GTI. However, it is still accessible from the selected car via links, so may be relevant.

Fig 1: Exploded View Of Assembly Mounts

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

Bolt
- Tightening Specification. Refer to SUBFRAME MOUNT [For engine(s) CNSB, CNSA, CXBB, CXBA, CXCB, CXCA ] .
- Always replace
Engine Support
- Refer to SUBFRAME MOUNT [For engine(s) CNSB, CNSA, CXBB, CXBA, CXCB, CXCA ] .
Engine Mount
- Refer to SUBFRAME MOUNT [For engine(s) CNSB, CNSA, CXBB, CXBA, CXCB, CXCA ] .
Bolt
- Tightening Specification. Refer to SUBFRAME MOUNT [For engine(s) CNSB, CNSA, CXBB, CXBA, CXCB, CXCA ] .
- Always replace
Bolt
- Tightening Specification. Refer to SUBFRAME MOUNT [For engine(s) CNSB, CNSA, CXBB, CXBA, CXCB, CXCA ] .
- Always replace
Bolt
- Tightening Specification. Refer to SUBFRAME MOUNT [For engine(s) CNSB, CNSA, CXBB, CXBA, CXCB, CXCA ] .
- Always replace
Bolt
- Tightening Specification. Refer to SUBFRAME MOUNT [For engine(s) CNSB, CNSA, CXBB, CXBA, CXCB, CXCA ] .
- Always replace
Pendulum Support
Bolt
- Tightening Specification. Refer to PENDULUM SUPPORT, REMOVING AND INSTALLING [For engine(s) CNSB, CNSA, CXBB, CXBA, CXCB, CXCA ] .
- Always replace
- For pendulum support to subframe
Bolt
- Tightening Specification. Refer to PENDULUM SUPPORT, REMOVING AND INSTALLING [For engine(s) CNSB, CNSA, CXBB, CXBA, CXCB, CXCA ] .
- Always replace
- For pendulum support to transmission
- Transmission with threaded insert. Refer to Transmission with Threaded Insert (for Example Heli Coil) for Attaching the Pendulum Support
Bolt
- Tightening Specification. Refer to SUBFRAME MOUNT [For engine(s) CNSB, CNSA, CXBB, CXBA, CXCB, CXCA ] .
- Always replace
- For pendulum support to transmission
- Transmission with threaded insert. Refer to Transmission with Threaded Insert (for Example Heli Coil) for Attaching the Pendulum Support
Bolt
- 60 Nm +90°
- Replace after removing
- Tightening sequence. Refer to ASSEMBLY MOUNTS .
- For transmission mount to transmission bracket
Bolt
- 60 Nm +90°
- Replace after removing
- Tightening sequence. Refer to ASSEMBLY MOUNTS .
- For transmission mount to transmission bracket
- Quantity: 2
Transmission Mount
- Check the adjustment. Refer to SUBFRAME MOUNT [For engine(s) CNSB, CNSA, CXBB, CXBA, CXCB, CXCA ]
- Adjusting. Refer to SUBFRAME MOUNT, ADJUSTING [For engine(s) CNSB, CNSA, CXBB, CXBA, CXCB, CXCA ]
Bolt
- Tightening Specification. Refer to SUBFRAME MOUNT [For engine(s) CNSB, CNSA, CXBB, CXBA, CXCB, CXCA ] .
- Always replace
- Transmission mount to chassis
Bolt
- 40 Nm +90°
- Replace after removing
- Tightening sequence. Refer to ASSEMBLY MOUNTS .
- For transmission bracket to transmission
Transmission Bracket
- Illustration does not correspond to version in vehicle
Bolt
- 40 Nm +90°
- Replace after removing
- For transmission bracket to transmission
- Tightening sequence. Refer to ASSEMBLY MOUNTS .