Camshaft Timing Chain, Removing And Installing, Engine Codes CCHHB, CNTA, CXCA, CXDA, CXCB And CXDB: Installing

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Check that the crankshaft is at TDC. The flat area on the crankshaft -arrow- must be horizontal.

-- Draw the markings on the cylinder block -1-, as shown, with a waterproof marker.

-- Draw a marking -2- on the three stage chain sprocket tooth -1- with a waterproof marker.

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Turn the intermediate sprocket and balance shaft to the marks -arrow-, but do not loosen the bolt -1-.

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

NOTE:

The painted links of the chain must be positioned on the markings on the chain sprockets.

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

Ignore the position of any additional painted chain links that may also be present.

-- Lay the balance shaft drive chain, and position the painted links -arrows- on the chain sprocket markings.

-- Install the guide rail -1- and tighten the bolts -arrows-.

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Engage the camshaft timing chain with the painted links -arrows- on the camshaft pins.

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Lay the oil pump drive timing chain onto the three stage chain sprocket.

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Tilt the three stage chain sprocket in direction of -arrow- toward the engine and secure it to the crankshaft. The marks -arrows- must be positioned opposite each other.

-- Install the :T10531/2 in the crankshaft and tighten hand-tight.

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Install the :T10531/3 . Tighten the :T10531/4 hand-tight. Using a 32 mm open end wrench move the :T10531/3 back and forth slightly while doing this tighten the :T10531/4 until the chain sprocket is seated securely on the crankshaft splines. Now tighten the adjusting bolt -A-.

-- Position the painted chain link in the balance shaft drive chain -arrow- at the mark on the three stage chain sprocket. Install the tensioning rail -1- and the guide rail -2-. Tighten the bolts -3-.

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Install the chain tensioner -1-.

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Check the adjustment again. The painted chain links -arrows- must line up with the markings on the chain sprockets.

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Place the camshaft timing chain on the intake camshaft, exhaust camshaft and the crankshaft. Position the painted chain links -arrows- on the markings on the chain sprockets.

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Install the guide rail -2- and tighten the bolts -1-.

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Install the upper guide rail -1-.

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

The help of a second technician is necessary for the following step.

-- Turn the exhaust camshaft slightly in the direction of -arrow A- using the :T40266 and push the :T40271/1 out of the chain sprocket splines in direction of -arrow B-. Release the camshaft in the direction of -arrow C-, until the timing chain touches the guide rail -1-. Hold the camshaft in this position, install the tensioning rail -2- and tighten the bolts -3-.

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Install the chain tensioner -1- and tighten the bolts -arrows-.

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Install the chain tensioner -2-. The wire clip -arrow- must come in to contact with the oil pan upper section opening. Tighten the bolt -1- and remove the :T40011 .

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Turn the intake camshaft in the direction of the -arrow 1- using the :T40266 until the :T40271/2 -2- can be pushed out of the chain sprocket splines in direction of -arrow 2-. Release the camshaft.

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Remove the :T40271/1 and :T40271/2 .

-- Check the adjustment. The painted chain links -arrows- must line up with the markings on the chain sprockets.

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Install the bolts -arrows- and tighten them. Tightening specification. Refer to -item 4- OVERVIEW - CYLINDER HEAD List Item:Bolt.

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Lubricate the holes -arrows- with engine oil.

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

NOTE:

The adapter sleeve -1- is not present on every bearing bracket.

-- Attach the bearing mount. Do not tilt it when doing this. Hand-tighten the bolts -arrows-.

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Remove the :T40267 .

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Tighten the bearing bracket bolts. Refer to -item 5- OVERVIEW - CAMSHAFT TIMING CHAIN, ENGINE CODES CHHB, CNTA, CXCA, CXDA, CXCB AND CXDB List Item:Bolt.

-- Install the control valves -item 7- OVERVIEW - CAMSHAFT TIMING CHAIN, ENGINE CODES CHHB, CNTA, CXCA, CXDA, CXCB AND CXDB List Item:Control Valves.

-- Let the engine turn a second time in the direction of engine rotation.

NOTE:

Due to the ratio, the painted chain links no longer match up after the engine has been turned.

-- Remove the turning over tool and install the lower timing chain cover. Refer to Installing .

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

NOTE:

Tighten the bolts -1 and 4- with an additional turn after installing the vibration damper. The bolts must be removed again to install the vibration damper.

-- Install the vibration damper. Refer to VIBRATION DAMPER, REMOVING AND INSTALLING .

-- Install the upper timing chain cover. Refer to UPPER TIMING CHAIN COVER, REMOVING AND INSTALLING .

-- Install the ribbed belt tensioner. Refer to RIBBED BELT TENSIONER, REMOVING AND INSTALLING .

-- Install the ribbed belt. Refer to RIBBED BELT, REMOVING AND INSTALLING .

Further installation is performed in reverse order of removal, while noting the following:

-- After performing work on the chain drive the adaptation value in the engine control module must be adapted. To do so, turn on the ignition and select the following menu items on the Vehicle Diagnostic Tester:

01 - Engine Electronics
Guided Functions
01 - Adaptation after repair work on the chain drive