LEMON Manuals: Even more car manuals for everyone
Home >> Volkswagen >> 2017 >> Golf S, Eng CD CXBA, Standard Trans >> Repair and Diagnosis >> Engine Mechanical >> Exhaust >> Engine & Transmission Systems (Diagnostics - CNSA, CNSB, CXBA, CXBB - 3 Of 4) >> St Generic Scan Tool >> Diagnosis And Testing >> Diagnostic Procedures >> Engine Component Power Supply Relay -J757-, CHECKING >> Test Procedure

Test Procedure

Step Procedure Result / Action to Take
1
  • PERFORM: Preliminary Check to verify the customers complaint. Refer to PRELIMINARY CHECK .
-- Was Complaint verified?		 -- YES:
  • GO TO Step 2.
-- NO:
  • GATHER more information from customer about the complaint.
2 
  • DISCONNECT: Engine Component Power Supply Relay -J757- from the Fuse box in the engine compartment.
  • CHECK: Engine Component Power Supply Relay -J757- harness connector terminal 111 and 113 to ground for voltage.
  • SPECIFIED VALUE: Battery voltage.
-- Was Value obtained?		 -- YES:
  • GO TO: Step 3.
-- NO:
  • PERFORM: Visual Inspection of wiring and component.
  • CHECK: Wiring for open, high resistance, short or harness connector for damage, corrosion, loose or broken terminals.
  • REPAIR: Faulty wiring or connector.
  • GO TO: Step 5.
3 
  • CONNECT: Jumper wire, Engine Component Power Supply Relay -J757- socket terminals 113 and 115.
  • DISCONNECT: Ignition Coil 1, 2, 3, 4 With Power Output Stage -N70, N127, N291, N292- harness connectors.
  • CHECK: Ignition Coil 1, 2, 3, 4 With Power Output Stage -N70, N127, N291, N292- harness connector terminal 4 to ground for voltage.
  • SPECIFIED VALUE: Battery voltage.
-- Were Values obtained?		 -- YES:
  • GO TO Step 4.
-- NO:
  • PERFORM: Visual Inspection of wiring and component.
  • CHECK: Wiring for open, high resistance, short or harness connector for damage, corrosion, loose or broken terminals.
  • REPAIR: Faulty wiring or connector.
  • GO TO: Step 5.
4 
  • REMOVE: Jumper wire, Engine Component Power Supply Relay -J757- socket terminals 113 and 115.
  • REMOVE: Engine Control Module -J623-. Refer to appropriate repair manual.
  • CHECK: Engine Component Power Supply Relay -J757- harness connector terminal 112 to the Engine Control Module -J623- harness connector T91 / 8 for resistance.
  • SPECIFIED VALUE: 0.5 Ω (± 0.3 Ω).
-- Was Value obtained?		 -- YES:
  • REPLACE: Engine Component Power Supply Relay -J757-. Refer to appropriate repair manual.
  • GO TO: Step 5.
-- NO:
  • PERFORM: Visual Inspection of wiring and component.
  • CHECK: Wiring for open, high resistance, short or harness connector for damage, corrosion, loose or broken terminals.
  • REPAIR: Faulty wiring or connector.
  • GO TO: Step 5.
5 
  • Final Procedure 
  • Perform a road test to verify repair.
-- Does the original DTC return?		 -- YES:
  • CHECK: Engine Control Module -J623- harness connector for any damaged, pushed-out pins.
  • REPAIR: As necessary.
  • Clear the DTC's. Refer to DIAGNOSTIC MODE 04 - ERASE DTC MEMORY .
  • Repair is complete. Generate Readiness Code. Refer to READINESS CODES .
  • Return vehicle to Customer.
  • If all electrical connections are OK:
  • REPLACE: Engine Control Module -J623-. Refer to appropriate repair manual.
  • Repair is complete. Generate Readiness Code. Refer to READINESS CODES .
  • Return vehicle to Customer.
-- NO:
  • Perform the diagnostic procedure for any DTC's.
  • If no DTC's return the repair is complete.
  • Return vehicle to customer.
scientia non olet · About LEMON Manuals