Camshaft, Removing And Installing. Engine Codes CXBA, CNSA, CXBB, And CNSB: Removing

NOTE:

The sealing surfaces of the lower cylinder head cover and on the upper cylinder head must not be reworked.

The camshaft bearings are integrated in the cylinder head or cylinder head cover. The tension must be released from the camshaft timing chain before removing the cylinder head cover.

When installing, secure all cable ties back to same positions.

-- Remove the air filter housing. Refer to AIR FILTER HOUSING, REMOVING AND INSTALLING .

-- Remove the upper coolant pipe. Refer to UPPER COOLANT PIPES, REMOVING AND INSTALLING .

-- Remove the ignition coils. Refer to IGNITION COILS WITH POWER OUTPUT STAGES, REMOVING AND INSTALLING .

-- Free up the connector from the clip -4- and pivot it forward.

-- Release the retainers -arrow-, remove the wiring duct upward from the bracket and move it towards the front.

-- Remove bolts -1, 2 and 3-. Carefully swing coolant line slightly toward the rear.

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

NOTE:

Risk of destroying the coolant pipes through deformation.

Never change the coolant pipe bent shape.

-- Disconnect the connector -1- from the EVAP Canister Purge Regulator Valve 1 -N80-.

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Press the release button on the crankcase ventilation hose -2- and remove the hose.

-- Remove the bolts -arrows- and the crankcase ventilation.

-- Remove the high pressure pump. Refer to HIGH PRESSURE PUMP, REMOVING AND INSTALLING .

-- Remove the vacuum pump. Refer to VACUUM PUMP, REMOVING AND INSTALLING .

-- Support the engine in the installation position. Refer to ENGINE, SUPPORTING IN INSTALLED POSITION .

-- Remove the engine mount. Refer to ENGINE MOUNT, REMOVING AND INSTALLING .

-- Remove the noise insulation. Refer to NOISE INSULATION .

-- Remove the right wheel housing liner front section. Refer to WHEEL HOUSING LINER .

-- Remove the engine support. Refer to ENGINE SUPPORT, REMOVING AND INSTALLING .

-- Remove the upper timing chain cover. Refer to UPPER TIMING CHAIN COVER, REMOVING AND INSTALLING .

NOTE:

To prevent damage from escaping coolant on the oil pressure switch, cover with a cloth.

-- Turn the vibration damper with the :T10355 to the "TDC point".

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

The markings -1- on the camshaft chain sprockets must be opposite the markings -2 and 3-.
The notch on the vibration damper and the marking on the lower timing chain cover -arrow- must be align.

-- Remove the lower timing chain cover. Refer to LOWER TIMING CHAIN COVER, REMOVING AND INSTALLING .

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

NOTE:

The control valve has left-hand threads.

Depending on the version, different control valves can be installed. Use a fitting assembly tool -1-.

-- Remove the left and right control valves using the :T10352/2 or :T10352/4 in the direction of -arrow-.

-- Remove the control valves with the :T10352/2 or :T10352/4 in the direction of -arrow-.

-- Remove the bolts -arrows- and remove the bearing bracket.

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Remove the bolts -arrows-.

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Install the :T40243 -arrows-.

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Press the chain tensioner circlip -1- together and hold it.

-- Slowly press and hold the :T40243 in the direction of -arrow-.

-- Secure the chain tensioner with the :T40267 .

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Remove the :T40243 .

-- Bolt the :T40271/2 to the cylinder head and slide into the splines on the chain sprocket in the direction of the arrow -2-. Turn the intake camshaft using the :T40266 -1- if necessary.

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Install the :T40271/1 on the cylinder head.

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

The help of a second technician is necessary for the following step.

-- Hold the exhaust camshaft securely with the :T10172A in direction of -arrow A-. Remove the bolt -1- and guide the tensioning rail -2- downward. Turn the camshaft clockwise in direction of -arrow A- until the Camshaft Locks:T40271/1 can be slid, in the direction of the -arrow B-, into the chain sprocket splines -C-

-- Check the installation position -C- of the :T40271/1 .

-- Remove the guide rail -1-. To do so, release the retainer -arrow- with a screwdriver and push the guide rail off toward the front.

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Press the oil pump chain tensioner bracket in direction of -arrow- and lock with :T40011 .

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Remove the bolt -1- and remove the chain tensioner.

-- Remove the bolts -1- and remove the glide rail -2-.

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Remove the camshaft timing chain from the camshaft sprockets and guide downward.

-- Install the :T10531/3 . In the "TDC point" the flat area -1- points upward. Install the :T10531/4 . Turn the crankshaft with a 32 mm open end wrench counter-clockwise out of "TDC".

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Turn the intake camshaft in the direction of the -arrow 1- using the :T40266 . Slide the :T40271/2 out of the chain sprocket splines in direction -arrow 2- and bring the camshaft into the rest position.

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Turn the exhaust camshaft using the :T10172A in direction of the -arrow A-. Slide the :T40271/1 out of the chain sprocket splines in the direction of the -arrow B- and bring the camshaft into the resting position.

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Remove the cylinder head cover bolts in -1 to 6- sequence.

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Remove the cylinder head cover.

-- Remove the camshaft and cover the open engine components.