Camshaft Timing Chain, Removing And Installing, Engine Codes CCHHB, CNTA, CXCA, CXDA, CXCB And CXDB: Removing

-- Support the engine in the installation position. Refer to ENGINE, SUPPORTING IN INSTALLED POSITION .

-- Remove the engine mount. Refer to ENGINE MOUNT, REMOVING AND INSTALLING .

-- Remove the engine support. Refer to ENGINE SUPPORT, REMOVING AND INSTALLING .

-- Remove the upper timing chain cover. Refer to UPPER TIMING CHAIN COVER, REMOVING AND INSTALLING .

-- Remove the noise insulation. Refer to NOISE INSULATION .

-- Remove the right wheel housing liner front section. Refer to WHEEL HOUSING LINER .

-- Turn the vibration damper with the Counterhold - Vibration Damper:T10355  to the "TDC point".

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

• The markings -1- on the camshaft chain sprockets must be opposite the markings -2 and 3-.
• The notch on the vibration damper and the marking on the lower timing chain cover -arrow- must be align.

-- Remove the lower timing chain cover. Refer to LOWER TIMING CHAIN COVER, REMOVING AND INSTALLING .

-- Remove the left and right control valve using the :T10352/2  or :T10352/4  in direction of -arrow-.

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Remove the bolts -arrows- and remove the bearing bracket.

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Remove the bolts -arrows-.

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Install the :T40243  -arrows-.

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Press the chain tensioner circlip -1- together and hold it.

-- Slowly press and hold the :T40243  in direction of -arrow-.

-- Secure the chain tensioner with the :T40267  .

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Remove the :T40243  .

-- Bolt the :T40271/2  to the cylinder head and slide into the splines on the chain sprocket in the direction of -arrow 2-. Rotate the intake camshaft with the :T40266  in direction of -arrows 1- if necessary.

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Install the :T40271/1  on the cylinder head.

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

The help of a second technician is necessary for the following step.

-- Hold the exhaust camshaft with the :T40266  in the direction of the -arrow A-. Remove the bolt -1- and guide the tensioning rail -2- downward. Turn the camshaft clockwise in direction of -arrow A- until the :T40271/1  can be pushed in the chain sprocket splines -arrow C-.

-- Remove the guide rail -1-. To do so, release the retainer -arrow- with a screwdriver and push the guide rail off toward the front.

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Remove the bolts -arrows- and remove the chain tensioner -1-.

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Press the oil pump chain tensioner bracket in direction of -arrow- and lock with :T40011  .

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Remove the bolt -1- and remove the chain tensioner.

-- Remove the bolts -1- and remove the guide rail -2-.

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Remove the camshaft timing chain from the camshaft sprockets and hang it on the camshaft pins -arrows-.

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Remove the chain tensioner -1- for the balance shaft timing chain.

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Remove the bolts -1-. Remove the tensioning rail -2- and the guide rails -3 and 4-.

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Loosen the adjusting bolt -A- and remove the tensioning pin -B-.

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Remove the oil pump drive timing chain to remove the three stage chain sprocket.

-- Remove the camshaft timing chain and drive chain for the balance shaft.