LEMON Manuals: Even more car manuals for everyone
Home >> Volkswagen >> 2009 >> GLI 2.0 J, Standard >> Repair and Diagnosis >> External Pages >> Different car >> Section 171 (Clutches - 0A4 (Sedan) (A5 Platform)) >> 30 Clutch >> Removal And Installation >> Mounting Bracket >> Removing

Mounting Bracket: Removing

WARNING: This page does not describe the selected car, but rather 6 other vehicles, including the 2010 Volkswagen Jetta, 2009 Volkswagen Jetta, 2008 Volkswagen Jetta, 2007 Volkswagen Jetta, and 2006 Volkswagen Jetta. However, it is still accessible from the selected car via links, so may be relevant.

-- Determine whether a coded radio is installed. If so, obtain the anti-theft code.

-- Turn off the ignition and disconnect the battery ground cable. Refer to Removal and Installation .

-- Remove the complete air filter housing if it located near the battery. Refer to one of the following:

Diesel engines, refer to [For engine(s) BRM] Description and Operation .

Gas engines, refer to [For engine(s) BGP, BGQ, CBTA, CBUA] Description and Operation .

-- Remove the battery and the battery tray. Refer to Removal and Installation .

NOTE:

Be careful not to get any brake fluid on the longitudinal member or on the transmission when performing the following work. If it does, clean the area thoroughly.

Place a lint free cloth under the master cylinder.

-- Clamp off the supply hose going to the master cylinder using 3094.

Fig 1: Identifying Clamp Tool 3094
GWWN30-10217Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Loosen the spring clamp -3- using VAS 6362 and remove the supply hose from the master cylinder.

Fig 2: Identifying Spring-Type Clamp, Supply Hose, Clip & Hose/Line Assembly
GWWN30-10121Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Moreover, after disconnecting, seal it using T10249/1 (→ top illustration).

-- Open the clip -2- using a screwdriver or with a pointed tool and remove the hose/line assembly (or plastic line) -1- from the master cylinder.

-- Unclip the clutch position sensor -G476- from the master cylinder -arrow- and remove it with the connector -4- still connected.

NOTE:

When working inside the footwell, cover the carpet with cloths to protect it from leaking brake fluid.

-- Remove the trim and the cover under the trim on the driver side. Refer to Removal and Installation .

There are different ways of securing the impact bolster support -1- in front of the clutch pedal -2-. The impact bolster support may look different than what is shown in the following illustrations. 

Fig 3: Identifying Impact Bolster & Front Of Clutch Pedal
GWWN34-10315Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

Securing with Two Bolts 

-- Remove the impact bolster support bolts and support -1-.

Securing with One Bolt 

Fig 4: Identifying Impact Bolster & Bolt
GWWN30-10117Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Remove the impact bolster support bolt -2- and support -1-.

Continuation for All 

-- Remove the damper -arrow- from the clutch pedal bracket, if equipped.

Fig 5: Identifying Bracket With Sound Absorber
GWWN30-10195Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Remove the retainers -A- for the damper.

Fig 6: Identifying Damper Retainers
GWWN30-10188Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Remove the damper.

-- Push the damper near the upper nut -1- above the clutch pedal -A- in the -direction of the arrow-.

Fig 7: Locating Damper Near The Upper Nut
GWWN30-10189Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Remove the nuts -1 and 2-.

Fig 8: Identifying Removal Of Mounting Bracket
GWWN30-10123Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

The upper nut -1- is accessible between the relay carrier and steering column trim.

-- Remove the bracket -3-.

scientia non olet · About LEMON Manuals