LEMON Manuals: Even more car manuals for everyone
Home >> Volkswagen >> 2006 >> GTI 1.8 E, Automatic >> Repair and Diagnosis >> External Pages >> Different car >> Section 283 (3.2L - Generic Scan Tool - Engine Code(S): CBRA) >> St Generic Scan Tool >> Diagnostic Trouble Code Tables >> Sae P0XXX Diagnostic Trouble Codes >> 02E Transmission

02E Transmission

WARNING: This page is about a different car, the 2008 Volkswagen R32. However, it is still accessible from the selected car via links, so may be relevant.
DTC Error Message Diagnostic Procedure Malfunction Criteria and Threshold Value Secondary Parameters with Enable Conditions Monitoring Time Length Frequency of checks, MIL Illumination
P0701 Transmission control system range/performance -- Replace the Direct Shift Gearbox (DSG) Mechatronic -J743-. Refer to DSG Transmission Mechatronic -J743-, TRANSMISSION INSTALLED .
  • Travel sensor voltage gearshift fork 1/3 out of plausibility range
  • Voltage < 300 mV or voltage > 4700 mV
   300 ms
  • Continuous
  • 2 DCY
P0702 Transmission control system electrical -- Replace the Direct Shift Gearbox (DSG) Mechatronic -J743-. Refer to DSG Transmission Mechatronic -J743-, TRANSMISSION INSTALLED .
  • In spite of the cut-off of the Common High-side Switch 1, a measurable current is present
  • In spite of the turned on Common High-side switch 1, no current is measurable
  • CHS 1 cut-off and CHS 1 Current is > 40mA
  • CHS 1 turned on and CHS 1 Current is < 200mA
  • Terminal 15 voltage < 18 V
  • Battery voltage > 9 V for more than 500ms
 300 ms
  • Continuous
  • 2 DCY
P0729 Gear 6 incorrect ratio -- Replace the Direct Shift Gearbox (DSG) Mechatronic -J743-. Refer to DSG Transmission Mechatronic -J743-, TRANSMISSION INSTALLED .
  • Calculate the speed of input shaft 2 with the sixth gear ratio and the output shaft speed
  • Compare the calculated speed with measured speed of input shaft 2
  • Speed difference magnitude > 50 RPM for more than 12020 ms
  • Control safety valve 2(on) >=20%
  • Multiplexer position =0
  • Control gearshift fork valve 3 >= 5%
  • Terminal 15 V > 4 V for more than 500 ms
  • Battery voltage > 9 V for more than 500 ms
  • Engine speed > 600 RPM for more than 500 ms
 12020 ms
  • Continuous
  • 2 DCY
P0731 Gear 1 incorrect ratio -- Replace the Direct Shift Gearbox (DSG) Mechatronic -J743-. Refer to DSG Transmission Mechatronic -J743-, TRANSMISSION INSTALLED .
  • Calculate the speed of input shaft 1 with the first gear ratio and the output shaft speed
  • Compare the calculated speed with measured speed of input shaft 1
Speed difference magnitude > 50 RPM for more than 120 ms
  • Control safety valve 1 (on) >=20%
  • Multiplexer position ==0
  • Control gearshift fork valve 1 >= 5%
  • Terminal 15 V > 4 V for more than 500 ms
  • Battery voltage > 9 V for more than 500 ms
  • Engine speed > 600 RPM for more than 500 ms
 12020 ms
  • Continuous
  • 2 DCY
P0732 Gear 2 incorrect ratio -- Replace the Direct Shift Gearbox (DSG) Mechatronic -J743-. Refer to DSG Transmission Mechatronic -J743-, TRANSMISSION INSTALLED .
  • Calculate the speed of input shaft 2 with the second gear ratio and the output shaft speed
  • Compare the calculated speed with measured speed of input shaft 2
  • Speed difference magnitude > 50 RPM for more than 120 ms
  • Control safety valve 2 (on) >=20%
  • Multiplexer position ==0
  • Control gearshift fork valve 3 >= 5%
  • Terminal 15 V > 4 V for more than 500 ms
  • Battery voltage > 9 V for more than 500 ms
  • Engine speed > 600 RPM for more than 500ms
 12020 ms
  • Continuous
  • 2 DCY
P0733 Gear 3 incorrect ratio -- Replace the Direct Shift Gearbox (DSG) Mechatronic -J743-. Refer to DSG Transmission Mechatronic -J743-, TRANSMISSION INSTALLED .
  • Calculate the speed of input shaft 1 with the third gear ratio and the output shaft speed
  • Compare the calculated speed with measured speed of input shaft 1
  • Speed difference magnitude > 50 RPM for more than 12020 ms
  • Control safety valve 1(on) >=20%
  • Multiplexer position ==0
  • Control gearshift fork valve 3 >= 5%
  • Terminal 15 V > 4 V for more than 500 ms
  • Battery voltage > 9 V for more than 500 ms
  • Engine speed > 600 RPM for more than 500 ms
 12020 ms
  • Continuous
  • 2 DCY
P0734 Gear 4 incorrect ratio -- Replace the Direct Shift Gearbox (DSG) Mechatronic -J743-. Refer to DSG Transmission Mechatronic -J743-, TRANSMISSION INSTALLED .
  • Calculate the speed of input shaft 2 with the fourth gear ratio and the output shaft speed
  • Compare the calculated speed with measured speed of input shaft 2
  • Speed difference magnitude > 50 RPM for more than 120 ms
  • Control safety valve 2 (on) >=20%
  • Multiplexer position ==1
  • Control gearshift fork valve 4 >= 5%
  • Terminal 15 V > 4 V for more than 500 ms
  • Battery voltage > 9 V for more than 500 ms
  • Engine speed > 600 RPM for more than 500 ms
 12020 ms
  • Continuous
  • 2 DCY
P0735 Gear 5 incorrect ratio -- Replace the Direct Shift Gearbox (DSG) Mechatronic -J743-. Refer to DSG Transmission Mechatronic -J743-, TRANSMISSION INSTALLED .
  • Calculate the speed of input shaft 1 with the fifth gear ratio and the output shaft speed
  • Compare the calculated speed with measured speed of input shaft 1
  • Speed difference magnitude > 50 RPM for more than 120 ms
  • Control safety valve 1(on) >=20%
  • Multiplexer position ==1
  • Control gearshift fork valve 1>= 5%
  • Terminal 15 V > 4 V for more than 500 ms
  • Battery voltage > 9 V for more than 500 ms
  • Engine speed > 600 RPM for more than 500 ms
 12020 ms
  • Continuous
  • 2 DCY
P0736 Reverse incorrect ratio -- Replace the Direct Shift Gearbox (DSG) Mechatronic -J743-. Refer to DSG Transmission Mechatronic -J743-, TRANSMISSION INSTALLED .
  • Calculate the speed of input shaft 1 with the reverse gear ratio and the output shaft speed
  • Compare the calculated speed with measured speed of input shaft 1
  • Speed difference magnitude > 50 RPM for more than 120 ms
  • Control safety valve 2(on) >=20%
  • Multiplexer position ==0
  • Control gearshift fork valve 4 >= 5%
  • Terminal 15 V > 4 V for more than 500 ms
  • Battery voltage > 9 V for more than 500 ms
  • Engine speed > 600 RPM for more than 500 ms
 12020 ms
  • Continuous
  • 2 DCY
P0736 Reverse incorrect ratio -- Replace the Direct Shift Gearbox (DSG) Mechatronic -J743-. Refer to DSG Transmission Mechatronic -J743-, TRANSMISSION INSTALLED .
  • Gearshift fork of reverse gear stays in shifted position in spite of command to disengage
  • Gearshift fork position < synchronizing point fifth gear -10%
  • Synchronizing point measured by a basic adjustment (reverse gear stays in shifted position)
  • Control valve gearshift fork valve 3 >= 5%
  • Control safety valve 2 (on) >=20%
  • Multiplexer position ==0
  • Desired main pressure > 2 bars
  • Terminal 15 V > 4 V for more than 500 ms
  • Battery voltage > 9 V for more than 500 ms
  • Engine speed > 600 RPM for more than 500 ms
 6 Socks
  • Continuous
  • 2 DCY
P0746 Pressure control solenoid A performance or stuck off -- Replace the Direct Shift Gearbox (DSG) Mechatronic -J743-. Refer to DSG Transmission Mechatronic -J743-, TRANSMISSION INSTALLED .
  • Desired valve current of clutch 1 exceeds a threshold; at the same time, the actual valve current is smaller than a second threshold desired current > 350 mA; actual current < 50 mA
 terminal 15 voltage > 4 V for more than 500ms 300 ms
  • Continuous
  • 2 DCY
P0746 Pressure control solenoid A performance or stuck off -- Replace the Direct Shift Gearbox (DSG) Mechatronic -J743-. Refer DSG Transmission Mechatronic -J743-, TRANSMISSION INSTALLED .
  • Integral of actual pressure minus desired pressure minus drain exceeds a maximum value pressure integral >= 0.1 bars
  • Desired pressure <= adapted clutch slipping point + 1 bar
  • Standing vehicle with accelerator pedal < 1.5%
  • Battery voltage > 9 V for more than 500 ms
  • Engine speed >600 RPM for more than 500 ms
 500 ms
  • Continuous
  • 2 DCY
P0747 Pressure control solenoid A stuck on -- Replace the Direct Shift Gearbox (DSG) Mechatronic -J743-. Refer to DSG Transmission Mechatronic -J743-, TRANSMISSION INSTALLED .
  • Comparison of actual valve current with desired valve current of clutch 1
  • Actual current > desired current, and (actual current - desired current) > 200 ma for more than 200 ms
  • Common high-side switch 1 on and not defective
  • Gearbox sub system 1 active
  • Common high-side switches not deactivated by module 2
  • Terminal 15 voltage > 4 V for more than 500 ms
 200 ms
  • Continuous
  • 2 DCY
P0751 Shift solenoid A performance or stuck off -- Replace the Direct Shift Gearbox (DSG) Mechatronic -J743-. Refer to DSG Transmission Mechatronic -J743-, TRANSMISSION INSTALLED . Comparison of residual current of gearbox sub system 1 (total current at common high-side switch 1 -actual current of clutch 1) at switching point of control gearshift fork valve 1 with residual current at permenant control of control gearshift fork valve 1 difference of residual current <= 200mA (supply voltage at common high-side 1 = 7 V).. 450mA (supply voltage at common high-side 1 = 13 V)
  • Common high-side switch 1 and 3 on and no defects
  • Gearbox sub system 1 active
  • Common high-side switches not deactivated by module 2
  • Duty factor change of safety valve 1 (control of safety valve 1 is stable) <= 5%
  • Duty factor change of gearshift fork valve 2 (control of gearshift fork valve 2 is stable) <= 5%
  • Duty factor of control gearshift fork valve 1 >70% and steady state time >= 50 ms
  • Terminal 15 voltage > 4 V for more than 500 ms
 300 ms
  • Continuous
  • 2 DCY
P0756 Shift solenoid B performance or stuck off -- Replace the Direct Shift Gearbox (DSG) Mechatronic -J743-. Refer to DSG Transmission Mechatronic -J743-, TRANSMISSION INSTALLED . Comparison of residual current of gearbox sub system 1 (total current at common high-side switch 1 -actual current of clutch 1) at switching point of control gearshift fork valve 2 with residual current at permenant control of control gearshift fork valve 2 difference of residual current <= 200 mA (supply voltage at common high-side 1 = 7 V).. 450 mA (supply voltage at common high-side 1 = 13 V)
  • Common high-side switch 1 and 3 on and no defects
  • Gearbox sub system 1 active
  • Common high-side switches not deactivated by module 2
  • Duty factor change of safety valve 1 (control of safety valve 1 is stable) <= 5%
  • Duty factor change of gearshift fork valve 1 (control of gearshift fork valve 1 is stable) <= 5%
  • Duty factor of control gearshift fork valve 2 >70% and steady state time >= 50 ms
  • Terminal 15 voltage > 4 V for more than 500 ms
 300 ms
  • Continuous
  • 2 DCY
P0761 Shift solenoid C performance or stuck off -- Replace the Direct Shift Gearbox (DSG) Mechatronic -J743-. Refer to DSG Transmission Mechatronic -J743-, TRANSMISSION INSTALLED . Comparison of residual current of gearbox sub system 2 (total current at common high-side switch 2 -actual current of clutch 2) at switching point of control gearshift fork valve 3 with residual current at permenant control of control gearshift fork valve 3 difference of residual current <= 200mA (supply voltage at common high-side 2 = 7 V).. 450mA (supply voltage at common high-side 2 = 13 V)
  • Common high-side switch 2 and 3 on, and no defects
  • Gearbox sub system 2 active
  • Common high-side switches not deactivated by module 2
  • Duty factor change of safety valve 2 (control of safety valve 2 is stable) <= 5%
  • Duty factor change of gearshift fork valve 4 (control of gearshift fork valve 4 is stable) <= 5%
  • Duty factor of control gearshift fork valve 3 >70% and steady state time >= 50 ms
  • Terminal 15 voltage > 4 V for more than 500 ms
 300 ms
  • Continuous
  • 2 DCY
P0766 Shift solenoid D performance or stuck off -- Replace the Direct Shift Gearbox (DSG) Mechatronic -J743-. Refer to DSG Transmission Mechatronic -J743-, TRANSMISSION INSTALLED . Comparison of residual current of gearbox sub system 2 (total current at common high-side switch 2 -actual current of clutch 2) at switching point of control gearshift fork valve 4 with residual current at permenant control of control gearshift fork valve 4 difference of residual current <= 200mA (supply voltage at common high-side 2 = 7 V).. 450mA (supply voltage at common high-side 2 = 13 V)
  • Common high-side switch 2 and 3 on, and no defects
  • Gearbox sub system 2 active
  • Common high-side switches not deactivated by module 2
  • Duty factor change of safety valve 2 (control of safety valve 2 is stable) <= 5%
  • Duty factor change of gearshift fork valve 3 (control of gearshift fork valve 3 is stable) <= 5%
  • Duty factor of control gearshift fork valve 4 >70% and steady state time >= 50 ms
  • Terminal 15 voltage > 4 V for more than 500 ms
 300 ms
  • Continuous
  • 2 DCY
P0771 Shift solenoid E performance or stuck off -- Replace the Direct Shift Gearbox (DSG) Mechatronic -J743-. Refer to DSG Transmission Mechatronic -J743-, TRANSMISSION INSTALLED .
  • Comparison of residual current of central control (total current at common high-side switch 3 -actual current of main pressure valve and cooling oil valve) at switching point of multiplexer valve with residual current at permanent control of multiplexer valve
  • Difference of residual current <= 150mA (maximum of supply voltage at common high-side 1 and 2 and terminal 15 = 7 V)
  • 300mA (maximum of supply voltage at common high-side 1 and 2 and terminal 15 = 13 V
  • Common high-side switch 3 on and no defects
  • Common high-side switches not deactivated by module 2
  • Multiplexer valve is controlled and steady state time (>= 50ms)
  • Terminal 15 voltage >4 V for more than 500 ms
 300 ms
  • Continuous
  • 2 DCY
P0776 Pressure control solenoid B performance or stuck off -- Replace the Direct Shift Gearbox (DSG) Mechatronic -J743-. Refer to DSG Transmission Mechatronic -J743-, TRANSMISSION INSTALLED . integral of actual pressure minus desired pressure, minus drain exceeds a maximum value pressure integral >= 0.1 bars
  • Desired pressure <= adapted clutch slipping point + 1 bar
  • Standing vehicle with accelerator pedal < 1.5%
  • Battery voltage > 9 V for more than 500 ms
  • Engine speed > 600 RPM for more than 500 ms
 500 ms
  • Continuous
  • 2 DCY
P0776 Pressure control solenoid B performance or stuck off -- Replace the Direct Shift Gearbox (DSG) Mechatronic -J743-. Refer to DSG Transmission Mechatronic -J743-, TRANSMISSION INSTALLED . Desired valve current of clutch 2 exceeds a threshold; at the same time, the actual valve current is smaller than a second threshold desired current > 350 mA; actual current < 50 mA Terminal 15 voltage > 4 V for more than 500 ms 300 ms
  • Continuous
  • 2 DCY
P0777 Pressure control solenoid B stuck on -- Replace the Direct Shift Gearbox (DSG) Mechatronic -J743-. Refer to DSG Transmission Mechatronic -J743-, TRANSMISSION INSTALLED .
  • Comparison of actual valve current with desired valve current of clutch 2
  • Actual current > desired current, and (actual current - desired current) > 200 ma for more than 200 ms
  • Common high-side switch 2 on and not defective
  • Gearbox sub system 2 active
  • Common high-side switches not deactivated by module 2
  • Terminal 15 voltage > 4 V for more than 500 ms
 200 ms
  • Continuous
  • 2 DCY
P0781 1-2 shift -- Replace the Direct Shift Gearbox (DSG) Mechatronic -J743-. Refer to DSG Transmission Mechatronic -J743-, TRANSMISSION INSTALLED .
  • Gearshift fork of first gear stays in shifted position in spite of command to disengage
  • Gearshift fork position > synchronizing point first gear + 10% synchronizing point measured by a basic adjustment (first gear stays in shifted position) control gearshift fork valve 2>=5%
  • Control safety valve 1 (on) >=20%
  • Multiplexer position ==0
  • Desired main pressure > 2 bars
  • Terminal 15 V > 4 V for more than 500 ms
  • Battery voltage > 9 V for more than 500 ms
  • Engine speed > 600 RPM for more than 500 ms
 6 Secs
  • Continuous
  • 2 DCY
P0782 2-3 shift -- Replace the Direct Shift Gearbox (DSG) Mechatronic -J743-. Refer to DSG Transmission Mechatronic -J743-, TRANSMISSION INSTALLED .
  • Gear shift fork of second gear stays in shifted position in spite of command to disengage
  • Gearshift fork position < synchronizing point second gear -10% synchronizing point measured by a basic adjustment (second gear stays in shifted position) control gearshift fork valve 4 >= 5%
  • Control safety valve 2(on) >=20%
  • Multiplexer position ==1
  • Desired main pressure > 2 bars
  • Terminal 15 V > 4 V for more than 500 ms
  • Battery voltage > 9 V for more than 500 ms
  • Engine speed > 600 RPM for more than 500 ms
 6 Secs
  • Continuous
  • 2 DCY
P0783 3-4 shift -- Replace the Direct Shift Gearbox (DSG) Mechatronic -J743-. Refer to DSG Transmission Mechatronic -J743-, TRANSMISSION INSTALLED .
  • Gearshift fork of third gear stays in shifted position in spite of command to disengage
  • Gearshift fork position < synchronizing point third gear -10% synchronizing point measured by a basic adjustment (third gear stays in shifted position) control valve gearshift fork valve 1 >= 5%
  • Control safety valve 1(on) >=20%
  • Multiplexer position ==0
  • Desired main pressure > 2bars
  • Terminal 15 V > 4 V for more than 500 ms
  • Battery voltage > 9 V for more than 500 ms
  • Engine speed > 600 RPM for more than 500 ms
 6 Secs
  • Continuous
  • 2 DCY
P0784 4-5 shift -- Replace the Direct Shift Gearbox (DSG) Mechatronic -J743-. Refer to DSG Transmission Mechatronic -J743-, TRANSMISSION INSTALLED .
  • Gearshift fork of fourth gear stays in shifted position in spite of command to disengage
  • Gearshift fork position >synchronizing point fourth gear +10% synchronizing point measured by a basic adjustment (fourth gear stays in shifted position) control valve gearshift fork valve 3 >= 5%
  • Control safety valve 2(on) >=20%
  • multiplexer position ==1
  • Desired main pressure > 2 bars
  • Terminal 15 V > 4 V for more than 500 ms
  • Battery voltage > 9 V for more than 500 ms
  • Engine speed > 600 RPM for more than 500 ms
 6 Secs
  • Continuous
  • 2 DCY
P0797 Pressure control solenoid C stuck on -- Replace the Direct Shift Gearbox (DSG) Mechatronic -J743-. Refer to DSG Transmission Mechatronic -J743-, TRANSMISSION INSTALLED . Comparison of actual valve current with desired valve current of main pressure solenoid valve actual current > desired current, and (actual current - desired current) > 200 ma for more than 300 ms
  • Common high-side switch 3 on and not defective common high-side switches not deactivated by module 2 common high-side switches not deactivated by module 2 terminal 15 voltage > 4 V for more than 500 ms
 300 ms
  • Continuous
  • 2 DCY
P0829 5-6 shift -- Replace the Direct Shift Gearbox (DSG) Mechatronic -J743-. Refer to DSG Transmission Mechatronic -J743-, TRANSMISSION INSTALLED .
  • Gearshift fork of fifth gear stays in shifted position in spite of command to disengage
  • Gearshift fork position >synchronizing point fifth gear +10% synchronizing point measured by a basic adjustment (fifth gear stays in shifted position) control valve gearshift fork valve 2 >= 5%
  • Control safety valve 1(on) >=20%
  • Multiplexer position ==1
  • Desired main pressure > 2bars
  • Terminal 15 V > 4 V for more than 500 ms
  • Battery voltage > 9 V for more than 500 ms
  • Engine speed > 600 RPM for more than 500 ms
 6 Secs
  • Continuous
  • 2 DCY
P0840 Transmission fluid pressure sensor/switch A circuit -- Replace the Direct Shift Gearbox (DSG) Mechatronic -J743-. Refer to DSG Transmission Mechatronic -J743-, TRANSMISSION INSTALLED .
  • Pressure sensor voltage clutch 1 out of plausibility range
voltage < 100 mV or voltage > 4900 mV		   300 ms
  • Continuous
  • 2 DCY
P0841 Transmission fluid pressure sensor/switch A circuit range/performance -- Replace the Direct Shift Gearbox (DSG) Mechatronic -J743-. Refer to DSG Transmission Mechatronic -J743-, TRANSMISSION INSTALLED . hydraulic pressure of clutch 1 exceeds a maximum value pressure >= 15.5 bars
  • Signal range check is correct
  • Terminal 15 voltage >4 V for more than 500 ms
  • Battery voltage >9 V for more than 500 ms
 1 Sec
  • Continuous
  • 2 DCY
P0845 Transmission fluid pressure sensor/switch B circuit -- Replace the Direct Shift Gearbox (DSG) Mechatronic -J743-. Refer to DSG Transmission Mechatronic -J743-, TRANSMISSION INSTALLED . pressure sensor voltage clutch 2 out of plausibility range voltage < 100mV or voltage > 4900mV   300ms
  • Continuous
  • 2 DCY
P0846 Transmission fluid pressure sensor/switch B circuit range/performance -- Replace the Direct Shift Gearbox (DSG) Mechatronic -J743-. Refer to DSG Transmission Mechatronic -J743-, TRANSMISSION INSTALLED . hydraulic pressure of clutch 2 exceeds a maximum value pressure >= 15.5 bars
  • Signal range check is correct
  • Terminal 15 voltage >4 V for more than 500 ms
  • Battery voltage >9 V for more than 500 ms
 1 Sec
  • Continuous
  • 2 DCY
P0864 TCM communication circuit range/performance -- Refer to DSG MECHATRONIC J743 CAN-BUS TERMINAL RESISTANCE, CHECKING .  
  • Terminal 15 voltage > 9 V for more than 500 ms
  • > 500 ms after reset
 80 ms
  • Continuous
  • 2 DCY
P0890 TCM power relay sense circuit low -- Replace the Direct Shift Gearbox (DSG) Mechatronic -J743-. Refer to DSG Transmission Mechatronic -J743-, TRANSMISSION INSTALLED . Detection by hardware circuit current >8.5 A terminal 15 voltage > 4 V for more than 500 ms 200 ms
  • Continuous
  • 2 DCY
P0892 TCM Power Relay Sense Circuit Intermittent -- Replace the Direct Shift Gearbox (DSG) Mechatronic -J743-. Refer to DSG Transmission Mechatronic -J743-, TRANSMISSION INSTALLED . Hardware detection
  • Filtered battery voltage, > 7 V
  • High side and low side FET, enabled
  • Status counter initialization, 0 or 1
 0.03 Seconds
  • Continuous
  • 2 DCY
P0914 Gear shift position circuit -- Check the selector mechanism. Refer to SELECTOR LEVER VOLTAGE SUPPLY, CHECKING . Selector lever position is not equal to negation of the inverse selector lever position OR selector lever position equals initialization value OR selector lever position equals error value OR selector lever position is equal to negation of the inverse selector position but no valid position Selector lever position ==Position 1 OR Position 2 OR Position 3 OR Position 4 OR Position L
  • No bus off error
  • No error failure of all CAN messages
  • No failure of selector lever CAN messages
  • Time after reset >1000 ms
  • Terminal 15 voltage > 9 V for more than 500 ms
 1 Sec
  • Continuous
  • 2 DCY
P0914 Gear shift position circuit -- Check the selector mechanism. Refer to SELECTOR LEVER VOLTAGE SUPPLY, CHECKING . If time out of the question and answer diagnosis is found, increment an event counter time out threshold > 100 ms
  • Gear message for selector lever is transmittable and selector lever message is receivable
  • No failure of selector lever CAN messages
  • Terminal 15 voltage > 4 V for more than 500 ms
 300 ms
  • Continuous
  • 2 DCY
P0919 Gear shift position control error -- Check the selector mechanism. Refer to SELECTOR LEVER VOLTAGE SUPPLY, CHECKING . Error flag of not determinable selector lever position is set
  • No failure of selector lever CAN messages
  • Terminal 15 voltage > 4 V for more than 500 ms
  • Battery voltage > 9 V for more than 500 ms
 20 ms
  • Continuous
  • 2 DCY
P0929 Gear shift lock solenoid control circuit range/performance -- Check the selector mechanism. Refer to SELECTOR LEVER VOLTAGE SUPPLY, CHECKING . If the shift-lock position signal is not valid (position !=error, not active, active or init) increment an event counter
  • No failure of selector lever CAN messages
  • Terminal 15 voltage > 4 V for more than 500 ms
 20 ms
  • Continuous
  • 2 DCY
scientia non olet · About LEMON Manuals