Selector Lever Cable, Through 02.09

Removing 

-- Move the selector lever into the "S" position.

-- Disconnect the selector lever cable -1- from the cable bracket -2- and remove it.

Fig 1: Identifying Cable Disengaged And Removed From Mounting Bracket

Courtesy of VOLKSWAGEN UNITED STATES, INC.

Be careful not to bend the cable. Do not use pliers, otherwise the tabs on the cable bracket may break off.

-- Pry the cable -1- off the selector shaft lever -3- using a open end wrench -2-.

Fig 2: Prying Selector Lever Cable From Lever/Selector Shaft Using A 10 mm Open-End Wrench

Courtesy of VOLKSWAGEN UNITED STATES, INC.

-- Lift the vehicle.

To remove the cable and/or the selector mechanism, remove the heat shield and, if necessary, any exhaust system components. Refer to Description and Operation[For engine(s) BGP, BGQ, CBTA, CBUA] Description and Operation[For engine(s) BPY] Description and Operation[For engine(s) CCTA] Description and Operation .

-- Remove the heat shield.

-- Remove the selector housing from under the selector mechanism.

Fig 3: Removing/Installing Selector Housing From Under Selector Mechanism

Courtesy of VOLKSWAGEN UNITED STATES, INC.

-- Remove the retainer. Always replace the retainer.

Fig 4: Removing Retainer

Courtesy of VOLKSWAGEN UNITED STATES, INC.

The selector housing is pushed forward on the cable.

Fig 5: Identifying Selector Housing Is Pushed Forward On Cable

Courtesy of VOLKSWAGEN UNITED STATES, INC.

The retainer must be pushed forward in order to remove the cable -1-.

-- Push the pin upward at the same time with a screwdriver -2-.

Fig 6: Identifying Retainer Must Be Pushed Forward In Order To Remove Cable & Pushing Pin Upward At Same Time With Screwdriver

Courtesy of VOLKSWAGEN UNITED STATES, INC.

-- Insert the screwdriver from underneath while pushing the retainer forward.

Fig 7: Inserting Screwdriver From Underneath While Pushing Retainer Forward

Courtesy of VOLKSWAGEN UNITED STATES, INC.

For Clarity: 

• -1- push the retainer forward
• -2- push the pin upward

Fig 8: Pushing Retainer Forward & Pushing Pin Upward

Courtesy of VOLKSWAGEN UNITED STATES, INC.

-- Remove the selector lever cable.

Fig 9: Removing Selector Lever Cable

Courtesy of VOLKSWAGEN UNITED STATES, INC.

Remove the selector housing from the cable

Installing 

Do not grease the cable.

-- Route the selector lever cable so that it is free of tension and install it into cable bracket on the transmission but do not secure it yet.

-- When installing, make sure the selector lever cable is routed correctly.

-- Clip the selector lever cable into the bracket. Make sure that the bracket does not touch the transmission fluid cooler.

Nuts: 8 Nm

Fig 10: Identifying Selector Lever Cable Retainer And Bolts

Courtesy of VOLKSWAGEN UNITED STATES, INC.

-- Mount the selector housing on the cable.

-- Install the selector lever cable into the selector mechanism.

Fig 11: Installing Selector Lever Cable Into Selector Mechanism

Courtesy of VOLKSWAGEN UNITED STATES, INC.

-- Insert the cable into the bracket and then insert the pin through the eye from the top

Fig 12: Inserting Cable Into Bracket And Inserting Pin Through Eye From Top

Courtesy of VOLKSWAGEN UNITED STATES, INC.

Install the retainer only after having checked the cable for ease of movement. Refer to SELECTOR LEVER CABLE, CHECKING .

-- Secure the cable with a new retainer to the cable bracket on the selector mechanism.

Fig 13: Securing Cable With New Retainer To Cable Bracket On Selector Mechanism

Courtesy of VOLKSWAGEN UNITED STATES, INC.

-- Install the selector housing, the heat shield and the exhaust system.

Fig 14: Removing/Installing Selector Housing From Under Selector Mechanism

Courtesy of VOLKSWAGEN UNITED STATES, INC.

-- Adjust the selector lever cable after installing. Refer to SELECTOR LEVER CABLE, CHECKING .