Selector mechanism, disassembling and assembling
WARNING: This page does not describe the selected car, but rather 20 other vehicles, including the 2007 Volkswagen Golf, 2006 Volkswagen Golf, 2005 Volkswagen Jetta, 2005 Volkswagen Golf, and 2004 Volkswagen Jetta. However, it is still accessible from the selected car via links, so may be relevant.
NOTE:
Lubricate mounting points and contact surfaces with grease Part No. G 052 142 A2.
1 - Selector lever handle
- Press sleeve item -2 down and pull handle off upward.
2 - Sleeve
- Locates in selector lever handle
- Prevents selector lever handle from being pulled off
3 - Cover
- With selector indicator
- Clipped into frame item -7
4 - Cover strip
- Insert in frame item -7
5 - Selector lever position display
- Printed circuit for selector lever position display (illumination) is held in position by clips
- Contacts for selector lever position face to selector lever contact springs item -27
- Secure connector with retainer item -6 to frame item -7
- Insert fiber optic light guide and wiring to connector housing in mountings on frame
- Connecting and disconnecting connector. Refer to Shift lock solenoid -N110-, removing and installing
6 - Retainer
- Clip push-in housing into frame item -7
7 - Frame
- Carefully pry off in the corners
- Push in cover strip item -4
- Pay attention to position of printed circuits and wiring item -5
- When installing do not damage contact springs item -27 for selector lever display
8 - Bolt
- 7 Nm
- Locating spring item -12 and plate item -11 to frame
9 - Shim
10 - Locking segment
- Place on centralizing elements of selector lever housing item -16
11 - Plate
12 - Locating spring with roller
- Locates in the detent in selector lever item -13
13 - Selector lever
- With pull rod, spring, detent, contact spring for selector lever position and releasing locking cable
- Removing and installing. Refer to Selector lever, removing and installing
14 - Roller
- For releasing locking cable
15 - Circlip
16 - Selector lever housing
- Need not be removed to replace majority of individual parts, with exception of selector lever and shift lock solenoid
17 - Fulcrum pin
- Splined
- Grease shank
- Do not turn when installing selector lever
18 - Bolt
- 25 Nm
19 - Locking lever
- For locking cable
- For locking in selector lever position "P"
20 - Shim
21 - Bolt
22 - Gasket
- Always replace
23 - Cover
- For selector lever housing
24 - Bolt
- Qty. 14
25 - O-ring
- Always replace
26 - Bolt
- 8 Nm
- Qty. 2
27 - Contact spring
- For selector lever display
28 - Bolt
- 4 Nm
- Place selector lever in "P" to loosen and tighten
29 - Clip
30 - Steering lock
31 - Bolt
- Qty. 2
- Solenoid to selector lever housing
32 - Shift lock solenoid -N110-
- Removing and installing. Refer to Shift lock solenoid -N110-, removing and installing
- Can be checked in electrical test and in measured value block
Refer to 01 ON BOARD DIAGNOSTIC (OBD)
- Only remove and install with selector lever in position "1"
- Pay attention to spring and locking pin when removing
- Remove together with locking pin and spring. When doing this move selector lever back and forth slightly
- Route wiring with sufficient clearance to selector lever
33 - Cable tie
- Wiring/solenoid to selector lever housing
- Always replace
34 - Spring
35 - Locking pin
36 - Nut
- 13 Nm
- Always replace
37 - Washer
38 - Nut
- 25 Nm
- Qty. 2
- Always replace
39 - Locking cable
- For ignition key removal lock
- Must not be kinked
- Removing and installing. Refer to Locking cable, removing and installing
- Adjusting. Refer to Locking cable, adjusting
- Checking operation of the ignition key withdrawal lock. Refer to Checking operation of the ignition key withdrawal lock .
40 - Circlip
- Always replace
- For mounting selector lever cable to selector lever housing
- Install with angled end inside selector housing
41 - Gasket
- Always replace
42 - Selector lever cable
- Do not bend or kink
- If the outer cable is damaged the selector lever cable must be replaced
- Checking and adjusting. Refer to Selector lever cable, checking and adjusting
- Removing and installing. Refer to Selector lever cable, removing and installing
- Lightly grease ball socket and cable ends before installing
43 - Lever
- For selector shaft
44 - Support bracket
- For mounting selector lever cable on transmission
45 - Circlip
- Always replace