Test Table
WARNING: This page does not describe the selected car, but rather 20 other vehicles, including the 2007 Volkswagen Golf, 2006 Volkswagen Golf, 2005 Volkswagen Jetta, 2005 Volkswagen Golf, and 2004 Volkswagen Jetta. However, it is still accessible from the selected car via links, so may be relevant.
| Switch to voltage measuring range 20 V | ||||||
| Test step | VAG 1598/18 sockets | Test of |
|
Specified value | Correcting malfunction | |
| 1 | 23 + 1 | Supply voltage from TCM -J217- |
|
approx. battery voltage |
|
|
| 45 +1 |
|
|||||
| 2 | 15 + 1 | Brake Light Switch -F- |
|
Less than 1 V |
|
|
|
approx. battery voltage |
|
||||
| Switch to resistance measuring range 200 Ω | ||||||
| Test step | VAG 1598/18 sockets | Test of |
|
Specified value | Correcting malfunction | |
| 3 | 55 + 67 | Solenoid valve 1 |
|
55 to 65 Ω | ||
| 55 + 1 67 + 1 |
-N88- |
|
infinite Ω |
|
||
| 4 | 54 + 67 | Solenoid valve 2 |
|
55 to 65 Ω | ||
| 54 + 1 67 + 1 |
-N89- |
|
infinite Ω |
|
||
| 5 | 9 + 67 | Solenoid valve 3 |
|
55 to 65 Ω |
|
|
| 9 + 1 67 + 1 |
-N90- |
|
infinite Ω | Refer to Removing and installing conductor strip: Removing and installing conductor strip | ||
| 6 | 47 + 67 | Solenoid valve 4 |
|
4.5 to 6.5 Ω |
|
|
| 47 + 1 67 + 1 |
-N91- |
|
infinite Ω | . Refer to 38 AUTOMATIC TRANSMISSION - GEARS, HYDRAULIC CONTROLS | ||
| Switch to resistance measuring range 200 Ω | ||||||
| Test step | VAG 1598/18 sockets | Test of |
|
Specified value | Correcting malfunction | |
| 7 | 56 + 67 | Solenoid valve 5 |
|
55 to 65 Ω | ||
| 56 + 1 67 + 1 |
-N92- |
|
infinite Ω |
|
||
| 8 | 58 + 22 | Solenoid valve 6 |
|
4.5 to 6.5 Ω |
|
|
| 58 + 1 22 + 1 |
-N93- |
|
infinite Ω |
|
||
| 9 | 10 + 67 | Solenoid valve 7 |
|
55 to 65 Ω |
|
|
| 10 + 1 67 + 1 |
-N94- |
|
infinite Ω | . Refer to 38 AUTOMATIC TRANSMISSION - GEARS, HYDRAULIC CONTROLS | ||
| Switch to resistance measuring range 200 Ω | ||||||
| Test step | VAG 1598/18 sockets | Test of |
|
Specified value | Correcting malfunction | |
| 10 | 1 + 16 | Kick Down Switch -F8- |
|
infinite Ω |
|
|
| (can only be checked when switch is part of accelerator cable) |
|
|
||||
|
less than 1.5 Ω |
|
||||
| 11 | 23 + 29 | Shift Lock Solenoid -N110- |
|
12 to 15 Ω |
|
|
| Switch to resistance measuring range 2 M Ω | ||||||
| Test step | VAG 1598/18 sockets | Test of |
|
Specified value | Correcting malfunction | |
| 12 | 6 + 67 | Transmission Fluid Temperature Sensor -G93- |
|
|
||
|
||||||
| approx. 20 ° C | 0.247 M Ω | |||||
|
48.8 K Ω 7.4 K Ω |
|||||
| Switch to resistance measuring range 20 K Ω | ||||||
| Test step | VAG 1598/18 sockets | Test of |
|
Specified value | Correcting malfunction | |
| 13 | 20 + 65 | Vehicle Speed Sensor -G68- |
|
|
||
| min. | 0.8 K Ω |
|
||||
| max. | 0.9 K Ω | |||||
| 14 | 21 + 66 | Transmission Vehicle Speed Sensor -G38- |
|
|
||
| min. | 0.8 K Ω |
|
||||
| max. | 0.9 K Ω | |||||
Test step 15: Multi-Function Transmission Range (TR) Switch -F125-
- Disconnect connector from multi-function TR switch.
Connector pin assignment
1 - To Pin 63 of TCM connector
2 - To Pin 40 of TCM connector
3 - To Pin 1 of TCM connector (Ground)
4 - Vacant
5 - To Pin 18 of TCM connector
6 - To Pin 62 of TCM connector
7 - To Pin 23 of TCM connector (voltage supply terminal 15)
Checking supply voltage.
- Connect test box VAG 1598/18.
- Switch multimeter to 20 V measuring range.
- Switch ignition on.
- Measure between terminal 7 and terminal 3 (Ground) on connector disconnected from multi-function TR switch.
Specification: Battery voltage
- Measure from terminal 7 of connector to socket 1 on1598/18 (Ground).
- Measure from socket 23 (terminal 15) on 1598/18 to socket 1 on 1598/18 (Ground).
Specification: Battery voltage
If the specifications are not obtained:
- Repair wiring according to wiring diagram.
If the specifications are obtained:
- Check wiring further.
- Switch ignition off.
- Disconnect Park/Neutral Position (PNP) relay -J226-.
- Set multimeter to 200 Ω measuring range
Check the wiring between the multi-pin connector on the TCM and the connector on the multi-function TR switch.
- Measure between sockets 1 and 18 on VAG 1598/18.
Specification: Infinity Ω
- Measure between sockets 23 and 18 on VAG 1598/18.
Specification: Infinity Ω
- Measure between socket 18 on VAG 1598/18 and terminal 5 on connector.
Specification: Less than 1.5 Ω
If the specifications are not obtained:
- Repair wiring according to wiring diagram.
If the specifications are obtained:
- Check wiring further.
- Measure between sockets 1 and 63 on VAG 1598/18.
Specification: Infinity Ω
- Measure between sockets 23 and 63 on VAG 1598/18.
Specification: Infinity Ω
- Measure between socket 63 on VAG 1598/18 and terminal 1 on connector.
Specification: Less than 1.5 Ω
If the specifications are not obtained:
- Repair wiring according to wiring diagram.
If the specifications are obtained:
- Check wiring further.
- Measure between sockets 1 and 62 on VAG 1598/18.
Specification: Infinity Ω
- Measure between sockets 23 and 62 on VAG 1598/18.
Specification: Infinity Ω
- Measure between socket 62 on VAG 1598/18 and terminal 6 on connector.
Specification: Less than 1.5 Ω
If the specifications are not obtained:
- Repair wiring according to wiring diagram.
If the specifications are obtained:
- Check wiring further.
- Measure between sockets 1 and 40 on VAG 1598/18.
Specification: Infinity Ω
- Measure between sockets 23 and 40 on VAG 1598/18.
Specification: Infinity Ω
- Measure between socket 40 on VAG 1598/18 and terminal 2 on connector.
Specification: Less than 1.5 Ω
If the specifications are not obtained:
- Repair wiring according to wiring diagram.
If the specifications are obtained:
- Replace multi-function TR switch. Refer to Multi-Function Transmission Range (TR) Switch -F125- .
- Install Park/Neutral Position (PNP) relay -J226-.