Selector mechanism, disassembling and assembling

1 - Selector lever handle 

• Press sleeve item -2 down and pull handle off upward.

2 - Sleeve 

• Locates in selector lever handle
• Prevents selector lever handle from being pulled off

3 - Cover 

• With selector indicator
• Clipped into frame item -7

4 - Cover strip 

• Insert in frame item -7

5 - Selector lever position display 

• Printed circuit for selector lever position display (illumination) is held in position by clips
• Contacts for selector lever position face to selector lever contact springs item -27
• Secure connector with retainer item -6 to frame item -7
• Insert fiber optic light guide and wiring to connector housing in mountings on frame

• Connecting and disconnecting connector. Refer to Shift lock solenoid -N110-, removing and installing 

6 - Retainer 

• Clip push-in housing into frame item -7

7 - Frame 

• Carefully pry off in the corners
• Push in cover strip item -4
• Pay attention to position of printed circuits and wiring item -5
• When installing do not damage contact springs item -27 for selector lever display

8 - Bolt 

• 7 Nm
• Locating spring item -12 and plate item -11 to frame

9 - Shim 

10 - Locking segment 

• Place on centralizing elements of selector lever housing item -16

11 - Plate 

12 - Locating spring with roller 

• Locates in the detent in selector lever item -13

13 - Selector lever 

• With pull rod, spring, detent, contact spring for selector lever position and releasing locking cable
• Removing and installing. Refer to Selector lever, removing and installing 

14 - Roller 

• For releasing locking cable

15 - Circlip 

16 - Selector lever housing 

• Need not be removed to replace majority of individual parts, with exception of selector lever and shift lock solenoid

17 - Fulcrum pin 

• Splined
• Grease shank
• Do not turn when installing selector lever

18 - Bolt 

• 25 Nm

19 - Locking lever 

• For locking cable
• For locking in selector lever position "P"

20 - Shim 

21 - Bolt 

22 - Gasket 

• Always replace

23 - Cover 

• For selector lever housing

24 - Bolt 

• Qty. 14

25 - O-ring 

• Always replace

26 - Bolt 

• 8 Nm
• Qty. 2

27 - Contact spring 

• For selector lever display

28 - Bolt 

• 4 Nm
• Place selector lever in "P" to loosen and tighten

29 - Clip 

30 - Steering lock 

31 - Bolt 

• Qty. 2
• Solenoid to selector lever housing

32 - Shift lock solenoid -N110- 

• Removing and installing. Refer to Shift lock solenoid -N110-, removing and installing 
• Can be checked in electrical test and in measured value block

Refer to 01 ON BOARD DIAGNOSTIC (OBD)

• Only remove and install with selector lever in position "1"
• Pay attention to spring and locking pin when removing
• Remove together with locking pin and spring. When doing this move selector lever back and forth slightly
• Route wiring with sufficient clearance to selector lever

33 - Cable tie 

• Wiring/solenoid to selector lever housing
• Always replace

34 - Spring 

35 - Locking pin 

36 - Nut 

• 13 Nm
• Always replace

37 - Washer 

38 - Nut 

• 25 Nm
• Qty. 2
• Always replace

39 - Locking cable 

• For ignition key removal lock
• Must not be kinked
• Removing and installing. Refer to Locking cable, removing and installing 
• Adjusting. Refer to Locking cable, adjusting 

• Checking operation of the ignition key withdrawal lock. Refer to Checking operation of the ignition key withdrawal lock  .

40 - Circlip 

• Always replace
• For mounting selector lever cable to selector lever housing
• Install with angled end inside selector housing

41 - Gasket 

• Always replace

42 - Selector lever cable 

• Do not bend or kink
• If the outer cable is damaged the selector lever cable must be replaced
• Checking and adjusting. Refer to Selector lever cable, checking and adjusting 
• Removing and installing. Refer to Selector lever cable, removing and installing 

• Lightly grease ball socket and cable ends before installing

43 - Lever 

• For selector shaft

44 - Support bracket 

• For mounting selector lever cable on transmission

45 - Circlip 

• Always replace