Table of shims for drive pinion and input gear
WARNING: This page is about a different variant/trim than selected.
| Gauged thickness (mm) |
Shim to be fitted (mm) |
Gauged thickness (mm) |
Shim to be fitted (mm) |
Gauged thickness (mm) |
Shim to be fitted (mm) |
| 0.975... 0.999 1.000... 1.024 1.025... 1.049 1.050... 1.074 1.075... 1.099 1.100... 1.124 1.125... 1.149 1.150... 1.174 1.175... 1.199 1.200... 1.224 1.225... 1.249 1.250... 1.274 1.275... 1.299 1.300... 1.324 1.325... 1.349 1.350... 1.374 1.375... 1.399 1.400... 1.424 1.425... 1.449 1.450... 1.474 1.475... 1.499 1.500... 1.524 1.525... 1.549 |
1.000 1.025 1.050 1.075 1.100 1.125 1.150 1.175 1.200 1.225 1.250 1.275 1.300 1.325 1.350 1.375 1.400 1.425 1.450 1.475 1.500 1.525 1.550 |
1.550... 1.574 1.575... 1.599 1.600... 1.624 1.625... 1.649 1.650... 1.674 1.675... 1.699 1.700... 1.724 1.725... 1.749 1.750... 1.774 1.775... 1.799 1.800... 1.824 1.825... 1.849 1.850... 1.874 1.875... 1.899 1.900... 1.924 1.925... 1.949 1.950... 1.974 1.975... 1.999 2.000... 2.024 2.025... 2.049 2.050... 2.074 2.075... 2.099 2.100... 2.124 |
1.575 1.600 1.625 1.650 1.675 1.700 1.725 1.750 1.775 1.800 1.825 1.850 1.875 1.900 1.925 1.950 1.975 2.000 2.025 2.050 2.075 2.100 2.125 |
2.125... 2.149 2.150... 2.174 2.175... 2.199 2.200... 2.224 2.225... 2.249 2.250... 2.274 2.275... 2.299 2.230... 2.324 2.325... 2.349 2.350... 2.374 2.375... 2.399 2.400... 2.424 2.425... 2.449 2.450... 2.474 2.475... 2.499 2.500... 2.524 2.525... 2.549 2.550... 2.574 2.575... 2.599 2.600... 2.624 2.625... 2.649 2.650... 2.674 2.675... 2.700 |
2.150 2.175 2.200 2.225 2.250 2.275 2.300 2.325 2.350 2.375 2.400 2.425 2.450 2.475 2.500 2.525 2.550 2.575 2.600 2.625 2.650 2.675 2.700 |
Different tolerances enable the required shim thickness to be measured precisely.
Part number:
Refer to Parts catalog