Test Table
WARNING: This page is about a different variant/trim than selected.
| Switch to voltage measuring range 20 V | ||||||
| Test step | VAG 1598/18 sockets | Test of |
|
Specified value | Correcting malfunction | |
| 1 | 23 + 1 | Supply voltage from TCM -J217- |
|
approx. battery voltage |
|
|
| 45 +1 |
|
|||||
| 2 | 15 + 1 | Brake Light Switch -F- |
|
Less than 1 V |
|
|
|
approx. battery voltage |
|
||||
| Switch to resistance measuring range 200 Ω | ||||||
| Test step | VAG 1598/18 sockets | Test of |
|
Specified value | Correcting malfunction | |
| 3 | 55 + 67 | Solenoid valve 1 |
|
55 to 65 Ω | ||
| 55 + 1 67 + 1 |
-N88- |
|
infinite Ω |
|
||
| 4 | 54 + 67 | Solenoid valve 2 |
|
55 to 65 Ω | ||
| 54 + 1 67 + 1 |
-N89- |
|
infinite Ω |
|
||
| 5 | 9 + 67 | Solenoid valve 3 |
|
55 to 65 Ω |
|
|
| 9 + 1 67 + 1 |
-N90- |
|
infinite Ω | Refer to Removing and installing conductor strip: Removing and installing conductor strip | ||
| 6 | 47 + 67 | Solenoid valve 4 |
|
4.5 to 6.5 Ω |
|
|
| 47 + 1 67 + 1 |
-N91- |
|
infinite Ω | . Refer to 38 AUTOMATIC TRANSMISSION - GEARS, HYDRAULIC CONTROLS | ||
| Switch to resistance measuring range 200 Ω | ||||||
| Test step | VAG 1598/18 sockets | Test of |
|
Specified value | Correcting malfunction | |
| 7 | 56 + 67 | Solenoid valve 5 |
|
55 to 65 Ω | ||
| 56 + 1 67 + 1 |
-N92- |
|
infinite Ω |
|
||
| 8 | 58 + 22 | Solenoid valve 6 |
|
4.5 to 6.5 Ω |
|
|
| 58 + 1 22 + 1 |
-N93- |
|
infinite Ω |
|
||
| 9 | 10 + 67 | Solenoid valve 7 |
|
55 to 65 Ω |
|
|
| 10 + 1 67 + 1 |
-N94- |
|
infinite Ω | . Refer to 38 AUTOMATIC TRANSMISSION - GEARS, HYDRAULIC CONTROLS | ||
| Switch to resistance measuring range 200 Ω | ||||||
| Test step | VAG 1598/18 sockets | Test of |
|
Specified value | Correcting malfunction | |
| 10 | 1 + 16 | Kick Down Switch -F8- |
|
infinite Ω |
|
|
| (can only be checked when switch is part of accelerator cable) |
|
|
||||
|
less than 1.5 Ω |
|
||||
| 11 | 23 + 29 | Shift Lock Solenoid -N110- |
|
12 to 15 Ω |
|
|
| Switch to resistance measuring range 2 M Ω | ||||||
| Test step | VAG 1598/18 sockets | Test of |
|
Specified value | Correcting malfunction | |
| 12 | 6 + 67 | Transmission Fluid Temperature Sensor -G93- |
|
|
||
|
||||||
| approx. 20 ° C | 0.247 M Ω | |||||
|
48.8 K Ω 7.4 K Ω |
|||||
| Switch to resistance measuring range 20 K Ω | ||||||
| Test step | VAG 1598/18 sockets | Test of |
|
Specified value | Correcting malfunction | |
| 13 | 20 + 65 | Vehicle Speed Sensor -G68- |
|
|
||
| min. | 0.8 K Ω |
|
||||
| max. | 0.9 K Ω | |||||
| 14 | 21 + 66 | Transmission Vehicle Speed Sensor -G38- |
|
|
||
| min. | 0.8 K Ω |
|
||||
| max. | 0.9 K Ω | |||||
Test step 15: Multi-Function Transmission Range (TR) Switch -F125-
- Disconnect connector from multi-function TR switch.
Connector pin assignment
1 - To Pin 63 of TCM connector
2 - To Pin 40 of TCM connector
3 - To Pin 1 of TCM connector (Ground)
4 - Vacant
5 - To Pin 18 of TCM connector
6 - To Pin 62 of TCM connector
7 - To Pin 23 of TCM connector (voltage supply terminal 15)
Checking supply voltage.
- Connect test box VAG 1598/18.
- Switch multimeter to 20 V measuring range.
- Switch ignition on.
- Measure between terminal 7 and terminal 3 (Ground) on connector disconnected from multi-function TR switch.
Specification: Battery voltage
- Measure from terminal 7 of connector to socket 1 on1598/18 (Ground).
- Measure from socket 23 (terminal 15) on 1598/18 to socket 1 on 1598/18 (Ground).
Specification: Battery voltage
If the specifications are not obtained:
- Repair wiring according to wiring diagram.
If the specifications are obtained:
- Check wiring further.
- Switch ignition off.
- Disconnect Park/Neutral Position (PNP) relay -J226-.
- Set multimeter to 200 Ω measuring range
Check the wiring between the multi-pin connector on the TCM and the connector on the multi-function TR switch.
- Measure between sockets 1 and 18 on VAG 1598/18.
Specification: Infinity Ω
- Measure between sockets 23 and 18 on VAG 1598/18.
Specification: Infinity Ω
- Measure between socket 18 on VAG 1598/18 and terminal 5 on connector.
Specification: Less than 1.5 Ω
If the specifications are not obtained:
- Repair wiring according to wiring diagram.
If the specifications are obtained:
- Check wiring further.
- Measure between sockets 1 and 63 on VAG 1598/18.
Specification: Infinity Ω
- Measure between sockets 23 and 63 on VAG 1598/18.
Specification: Infinity Ω
- Measure between socket 63 on VAG 1598/18 and terminal 1 on connector.
Specification: Less than 1.5 Ω
If the specifications are not obtained:
- Repair wiring according to wiring diagram.
If the specifications are obtained:
- Check wiring further.
- Measure between sockets 1 and 62 on VAG 1598/18.
Specification: Infinity Ω
- Measure between sockets 23 and 62 on VAG 1598/18.
Specification: Infinity Ω
- Measure between socket 62 on VAG 1598/18 and terminal 6 on connector.
Specification: Less than 1.5 Ω
If the specifications are not obtained:
- Repair wiring according to wiring diagram.
If the specifications are obtained:
- Check wiring further.
- Measure between sockets 1 and 40 on VAG 1598/18.
Specification: Infinity Ω
- Measure between sockets 23 and 40 on VAG 1598/18.
Specification: Infinity Ω
- Measure between socket 40 on VAG 1598/18 and terminal 2 on connector.
Specification: Less than 1.5 Ω
If the specifications are not obtained:
- Repair wiring according to wiring diagram.
If the specifications are obtained:
- Replace multi-function TR switch. Refer to Multi-Function Transmission Range (TR) Switch -F125- .
- Install Park/Neutral Position (PNP) relay -J226-.