LEMON Manuals: Even more car manuals for everyone
Home >> Volkswagen >> 2001 >> Jetta GL, 2.0 B >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 42 (4 SPD. Automatic Transmission 01M On Board Diagnostic (OBD) (A4 Platform)) >> 01 On Board Diagnostic (OBD) >> On Board Diagnostic (OBD), performing >> Test Table >> Checking solenoid valves while driving

Checking solenoid valves while driving

WARNING: This page is about a different variant/trim than selected.
Group No.  Display field  Designation  Test conditions 
 
 
Selector lever in: 		 Specified readout on VAG 1551  Correcting malfunction 
004 1 Solenoid valves/indicated on   P  1 0 1 0 00 Solenoid valves are selected according to driving condition
    VAG 1551 display   R1)  0 0 1 0 00
  • Perform
        N  1 0 1 0 00   electrical check
    -N88- Display 1 D1) 1H 0 0 1 0 00   Refer to Transmission, electrical check 
    -N89- Display 2   1M 0 0 1 0 00  
    -N90- Display 3   2H 0 1 1 0 00    
    -N91- Display 4   2M 0 1 1 0 00  
    -N92- Display 5   3H 0 0 0 0 00    
    -N94- Display 6   3M 0 0 0 0 00  
        4H 1 1 0 0 01  
continued     4M 1 1 0 0 01  
1) While driving with gears selected a second technician is required for reading the specified values.
Group No.  Display field  Designation  Test conditions 
 
 
Selector lever in: 		 Specified readout on VAG 1551  Correcting malfunction 
004 1 Solenoid valves/indicated on 31) 1H 0 0 1 0 00 Solenoid valves are selected according to driving condition
    VAG 1551:   1M 0 0 1 0 00
  • Perform
    -N88- Display 1   2H 0 1 1 0 00   electrical check
    -N89- Display 2   2M 0 1 1 0 00 Refer to Transmission, electrical check 
    -N90- Display 3   3H 0 0 0 0 00    
    -N91- Display 4   3M 0 0 0 0 00    
    -N92- Display 5 21) 1H 0 0 1 0 00    
    -N94- Display 6   1M 0 0 1 0 00  
        2H 0 1 1 0 00    
        2M 0 1 1 0 00  
      11) 1H 0 0 1 0 00    
        1M 0 0 1 0 00  
1) While driving with gears selected a second technician is required for reading the specified values.
Group No.  Display field  Designation  Test conditions  Specified readout on VAG 1551  Correcting malfunction 
004 2 Gear selected Driving1) Neutral 0
        Reverse R  
        1 hydraulic 1H  
          1 mechanical 1M  
        2 hydraulic 2H    
          2 mechanical 2M    
        3 hydraulic 3 H    
          3 mechanical 3M    
          4 hydraulic 4H    
cont'd       4 mechanical 4M    
1) When driving, a second technician is needed for reading the specified values.
Group No.  Display field  Designation  Test conditions  Specified readout on VAG 1551  Correcting malfunction 
004 3 Selector lever position Driving1) P P
          R R  
          N N  
          D D  
          3 3
          2 2  
          1 1  
  4 Vehicle speed Speed at which vehicle is being driven1) ..kph The speedometer reading and readout on VAG 1551 may differ slightly
1) When driving, a second technician is needed for reading the specified values.
Group No.  Display field  Designation  Test conditions  Specified readout on VAG 1551  Correcting malfunction 
005 1 ATF temperature, ATF level is checked at approx. 35 ° C - 45 ° C Stationary with engine running. The exact temperature is displayed from approx. 30 ° C .. ° C
  2 Shift outputs Driving1)
Ignition timing influence or injection quantity influence (only operative during a gear shift)		  
  • Check wiring and connectors according to wiring diagram, including CAN-Bus wiring
  • Check engine control module. Refer to 01 ON BOARD DIAGNOSTIC (OBD) for 1.9 LITER 4-CYL. 2V TDI FUEL INJECTION GLOW PLUG, ENGINE CODE: ALH, MY 1999-2001 and 01 ON BOARD DIAGNOSTIC (OBD) for 1.9 LITER 4-CYL. 2V TDI FUEL INJECTION GLOW PLUG, ENGINE CODE ALH, FROM MY 2002.
      Display 12) is switched on 1
  • Replace engine control module if necessary
        is switched off 0
      22) was switched on 1
cont'd     was switched off 0  
1) When driving, a second technician is needed for reading the specified values.
2) VAG 1551 must always show the same number "1" or "0" in displays 1 and 2.
Group No.  Display field  Designation  Test conditions  Specified read out VAG 1551  Correcting malfunction 
005 2 Shift outputs Shift Lock Solenoid -N110-    
      Display 3   is
switched on		 1
          is
switched off		 0  
      4   switched on 1  
          switched off 0  
        Cruise control system  
  • Check wiring and connectors according to wiring diagram, including CAN-Bus wiring
      5   switched on 1
  • Check cruise control system. Refer to Electrical Wiring Diagrams, Troubleshooting and Component Locations binder
cont'd         switched off 0    
Group No.  Display field  Designation  Test conditions  Specified readout on VAG 1551  Correcting malfunction 
005 2 Shift outputs
Display 6		 Air conditioner was switched off 1  
  • Check wiring according to wiring diagram
          was not
switched off		 0
      7 Park/Neutral signal
Selector lever in		  
  • Check wiring according to wiring diagram
          P, N 1    
          R 0  
cont'd.         D, 3, 2, 1 1 / 0 Selector lever positions D, 3, 2, 1 not applicable
Group No.  Display field  Designation  Test conditions  Specified readout on VAG 1551  Correcting malfunction 
005 3 Gear to be selected Driving1) Neutral 0
        Reverse R  
          1 hydraulic 1H
  • If gear shifts do not occur, a clutch or brake may be faulty
          1 mechanical 1M  
          2 hydraulic 2H  
          2 mechanical 2M    
        3 hydraulic 3 H
          3 mechanical 3M    
          4 hydraulic 4H    
        4 mechanical 4M    
1) When driving, a second technician is needed for reading the specified values.
Group No.  Display field  Designation  Test conditions  Specified readout on VAG 1551  Correcting malfunction 
005 4 Engine speed Driving1)
with engine running		 rpm
  • Perform OBD for relevant engine
  • Check wiring and connectors according to wiring diagram, including CAN-Bus wiring
006 Not applicable
1) When driving, a second technician is needed for reading the specified values.
Group No.  Display field  Designation  Test conditions  Specified readout on VAG 1551  Correcting malfunction 
007 1 Gear selected1)   Neutral 0
        Reverse R
  • If gear shifts do not occur, a clutch or brake may be faulty
          1 hydraulic 1H +/-  
          1 mechanical 1M +/-
          2 hydraulic 2H +/-
NOTE: The + (or -) sign relates to the speed information In display field 2.
          2 mechanical 2M +/-
        3 hydraulic 3 H +/-
          3 mechanical 3M +/-
          4 hydraulic 4H +/-
cont'd       4 mechanical 4M +/-
1) When driving, a second technician is needed for reading the specified values.
Group No. 
4		 Display field  Designation  Test conditions  Specified readout on VAG 1551  Correcting malfunction 
007 2 Torque converter lock-up clutch slip While driving1)
with engine running		 In the hydraulic gears2) 0... stall speed
  • Check wiring according to wiring diagram
    Solenoid valve 4 -N91- is activated Torque converter lock-up clutch closed Engine speed: 2000... 3000 rpm in the mechanical gears
3)		 0... 130
rpm
1) When driving, a second technician is needed for reading the specified values.
2) The torque converter lock-up clutch must be open! The lock-up clutch is open when "H" = hydraulic with slip, is displayed in display field 1. Additionally the character "+" or "-" is displayed. "+" signifies that the engine speed (pump speed) is greater than turbine speed (vehicle under traction). "-" signifies that the engine speed is less than the turbine speed (vehicle in overrun).
3) The gear shift must be completed. The torque converter lock-up clutch must be closed and the accelerator pedal value held constant (gears will be mechanically activated, "M").
Group No.  Display field  Designation  Test conditions  Specified readout on VAG 1551  Correcting malfunction 
007 3 Engine speed With engine running .. rpm
  4 Accelerator pedal value   Idling 0...1 % When accelerating from idling to wide open throttle the percentage value constantly increases
          Wide open throttle 99...100 %
008 Not applicable
scientia non olet · About LEMON Manuals