LEMON Manuals: Even more car manuals for everyone
Home >> Volkswagen >> 2001 >> Jetta GL, 2.0 B >> Repair and Diagnosis >> External Pages >> Different car >> Section 82 (5 SPD. Automatic Transmission 09A On Board Diagnostic (OBD)) >> 01 On Board Diagnostic (OBD) >> Transmission electrical check >> Test table

Test table

WARNING: This page does not describe the selected car, but rather 11 other vehicles, including the 2006 Volkswagen Golf, 2006 Volkswagen GTI, 2005 Volkswagen Jetta, 2005 Volkswagen Golf, and 2005 Volkswagen GTI. However, it is still accessible from the selected car via links, so may be relevant.
Switch to voltage measuring range 20 V 
Test step  V.A.G 1598/18 sockets  Test of 
  • Test conditions
  • Additional operations
 Specified value  Correction 
1 45 + 1
68 + 1		 Supply voltage for transmission control module (TCM) -J217-
(terminal 15)
  • Ignition switched on
 approx. battery voltage
  • Check wiring using wiring diagram
  • Check wiring from contact 1 to Ground
  • Check wiring from contact 45 + 68 to terminal 15 central electrics
  • Check battery, replace if necessary
  22 + 1
22 + 24		 Supply voltage for Diagnostic Trouble Code (DTC) memory in transmission control module (TCM) -J217-
(terminal 30)
  • Ignition switched off
 approx. battery voltage
  • Check wiring using wiring diagram
  • Check wiring from contact 1 to Ground
  • Check wiring from contact 22 to terminal 30 central electrics
  • Check battery, replace if necessary
Switch to voltage measuring range 20 V 
Test step  V.A.G 1598/18 sockets  Test of 
  • Test conditions
  • Additional operations
 Specified value  Correction 
2 6 + 1 Shift lock solenoid -N110-
  • Ignition switched off
 0 V
  • Check wiring using wiring diagram
     
  • Ignition switched on
 approx. battery voltage  
  Bridge
6 + 1		  
  • Disconnect test unit VAG 1526
  • Ignition switched on
  • Connect bridge with cables from VAG 1594
 Solenoid must audibly click
3 21 + 1 Brake light switch -F-
  • Brake pedal not depressed
 0 V
  • Check wiring according to wiring diagram
  • Replace brake light switch -F-
     
  • Brake pedal depressed
 approx. battery voltage . Refer to 01 ON BOARD DIAGNOSTIC (OBD) ; Electrical/electronic components and locations
Switch to resistance measuring range 20 k Ω 
Test step  V.A.G 1598/18 sockets  Test of 
  • Test conditions
  • Additional operations
 Specified value  Correction 
5 35 + 36 Vehicle speed sensor -G68- min. 0.4 k Ω
  • Check wiring using wiring diagram
      max. 0.6 k Ω
  • Replace vehicle speed sensor -G68-
6 9 + 10 Sensor for transmission RPM -G182- min. 0.4 k Ω
  • Check wiring using wiring diagram
      max. 0.6 k Ω
  • Replace sensor for transmission RPM -G182-
Switch to resistance measuring range 200 Ω 
Test step  V.A.G 1598/18 sockets  Test of 
  • Test conditions
  • Additional operations
 Specified value  Correction 
7 48 + 1 Solenoid valve 1 -N88-
  • Ignition switched off
 9 to 24 Ω
  • Check wiring using wiring diagram and replace wires if necessary
8 49 + 1 Solenoid valve 2 -N89-
  • Ignition switched off
 9 to 24 Ω  
9 26 + 1 Solenoid valve 3 -N90-
  • Ignition switched off
 9 to 24 Ω  
10 25 + 1 Solenoid valve 4 -N91-
  • Ignition switched off
 9 to 24 Ω  
11 50 + 1 Solenoid valve 5 -N92-
  • Ignition switched off
 9 to 24 Ω  
12 66 + 1 Solenoid valve 6 -N93-
  • Ignition switched off
 1 to 5 Ω  
13 46 + 1 Solenoid valve 8 -N281-
  • Ignition switched off
 9 to 24 Ω  
14 51 + 1 Solenoid valve 9 -N282-
  • Ignition switched off
 9 to 24 Ω  
15 65 + 1 Solenoid valve 10 -N283-
  • Ignition switched off
 1 to 5 Ω  
Switch to resistance measuring range 20 k Ω 
Test step  V.A.G 1598/18 sockets  Test of 
  • Test conditions
  • Additional operations
 Specified value  Correction 
16 33 + 34 Transmission fluid temperature sensor -G93- (ATF)    
  • Check wiring using wiring diagram
     
  • ATF temperature
    
      approx. 30 ° C 2.2 k Ω  
     
  • Switch multimeter to 2 k Ω
approx. 70 ° Capprox. 110 ° C		 0.5 k Ω
0.2 k Ω		  
17 28 +29 Intermediate shaft speed sensor -G265- min. 0.4 k Ω
  • Check wiring using wiring diagram
      max. 0.6 k Ω
  • Replace intermediate shaft speed sensor -G265-

After electrical checks:

NOTE: When installing connector ensure that the guides are engaged on the control module pins.
scientia non olet · About LEMON Manuals