DTC tables, vehicles through 05.01

NOTE:

The DTC table is listed according to the 5 digit code on the left.
Some of the mentioned DTC texts are only displayed on the VAS 5051. On the V.A.G 1551, only the DTC will be printed in this case.
The possible malfunctions are dependant on the respective vehicle equipment.
Explanation of the malfunction types (e.g. "open circuit/short circuit to Ground"):

Refer to Scan tool operating instructions

Before replacing components indicated as being malfunctioning, check the wiring and connectors to these components as well as the Ground connections using wiring diagram. This is particularly relevant if DTC's are output as "occurring sporadically" (SP).
The DTC's displayed can be localized using the test table.

NOTE:

This malfunction "no communication" can also appear with the door control modules. This has no influence on the function of the convenience system and is therefore of no consequence. Erase DTC memory.

Scan tool print-out: The number shown here in bold 049 (e.g.) has no relevance.

01333 049
Door CU -J388
no communication

V.A.G 1551 display		Possible cause	Corrective action
00000
No DTC recognized		If "No DTC recognized" appears after carrying out repairs On Board Diagnostic (OBD) is ended
00849
S-terminal on ignition/starter switch -D-
	Undefined switch condition	Terminal 15 OK. but S-terminal malfunctioning	Read Measuring Value Block; Display group number 006. Refer to Break down of display content for display group number 006 , Display zone 3
		Faulty wiring or connectors

V.A.G 1551 display		Possible cause	Corrective action
00893
Button for tailgate/trunk lid release - -E234-
	Implausible signal1)	Faulty wiring or connectors	Read Measuring Value Block; Display group number 014. Refer to Break down of display content for display group number 014 , display zone 2

1) DTC recorded if button pressed for longer than 5 minutes.

V.A.G 1551 display		Possible cause	Corrective action
00912
Electric window switch FL -E40-
	Implausible signal Short to Ground	Faulty wiring or connectors	Read Measuring Value Block; Display group number 002. Refer to Break down of display content for display group number 002 , display zone 1
		Button installation not OK., sticks when operated	Check button
		Electric window switch, FL -E40- malfunctioning
00913
Electric window switch FR, driver's door -E81-
	Implausible signal Short to Ground	Faulty wiring or connectors	Read Measuring Value Block; Display group number 002. Refer to Break down of display content for display group number 002 , display zone 2
		Button installation not OK., sticks when operated	Check button
		Electric window switch, FR -E81- malfunctioning

V.A.G 1551 display		Possible cause	Corrective action
00914
Electric window switch RL, driver's door -E53-
	Implausible signal Short to Ground	Faulty wiring or connectors	Read Measuring Value Block; Display group number 002. Refer to Break down of display content for display group number 002 , display zone 3
		Button installation not OK., sticks when operated	Check button
		Electric window switch, RL -E53- malfunctioning
00915
Electric window switch RR, driver's door -E55-
	Implausible signal Short to Ground	Faulty wiring or connectors	Read Measuring Value Block; Display group number 002. Refer to Break down of display content for display group number 002 , display zone 4
		Button installation not OK., sticks when operated	Check button
		Electric window switch, RR -E55- malfunctioning

V.A.G 1551 display		Possible cause	Corrective action
00928
Locking unit for driver's side CL -F220-
	Implausible signal	Faulty wiring or connectors	Check wiring and connectors using wiring diagram
		No voltage supply for central locking on driver's door	Check voltage supply to driver's door control module or to door main connector (lower left footwell)
		Lock unit mechanics and operating components are stiff/partially seized	Check lock unit mechanical components and operating components and make serviceable
		Locking unit for driver's side central locking -F220- malfunctioning	Replace locking unit for driver's door central locking -F220-
	Wrong equipment	Wrong locking unit installed1)	Replace locking unit

1) If a rest of world lock is installed in a USA vehicle, there is a safe feedback via an additional switch (safe switch).

V.A.G 1551 display		Possible cause	Corrective action
00929
Locking unit for front passenger's side CL -F221-
	Implausible signal	Faulty wiring or connectors	Check wiring and connectors using wiring diagram
		No voltage supply for central locking on front passengers door	Check voltage supply to front passenger's door control module or to door main connector (lower right footwell)
		Lock unit mechanics and operating components are stiff/partially seized	Check lock unit mechanical components and operating components and make serviceable
		Locking unit for front passenger's central locking -F221- malfunctioning	Replace locking unit for front passenger's door central locking -F221-
	Wrong equipment	Wrong locking unit installed1)	Replace locking unit

1) If a rest of world lock is installed in a USA vehicle, there is a safe feedback via an additional switch (safe switch).

V.A.G 1551 display		Possible cause	Corrective action
00930
Locking unit for rear left CL -F222-
	Implausible signal	Faulty wiring or connectors	Check wiring and connectors using wiring diagram
		No voltage supply for central locking on left rear door	Check voltage supply to left rear door control module or to door main connector (in B pillar left)
		Lock unit mechanics and operating components are stiff/partially seized	Check lock unit mechanical components and operating components and make serviceable
		Locking unit for rear left central locking -F222- malfunctioning	Replace locking unit for rear left central locking -F222-
	Wrong equipment	Wrong locking unit installed1)	Replace locking unit

1) If a rest of world lock is installed in a USA vehicle, there is a safe feedback via an additional switch (safe switch).

V.A.G 1551 display		Possible cause	Corrective action
00931
Locking unit for rear right CL -F223-
	Implausible signal	Faulty wiring or connectors	Check wiring and connectors using wiring diagram
		No voltage supply for central locking on right rear door	Check voltage supply to right rear door control module or to door main connector (in B pillar right)
		Lock unit mechanics and operating components are stiff/partially seized	Check lock unit mechanical components and operating components and make serviceable
		Locking unit for rear right central locking -F223- malfunctioning	Replace locking unit for rear right central locking -F223-
	Wrong equipment	Wrong locking unit installed1)	Replace locking unit

1) If a rest of world lock is installed in a USA vehicle, there is a safe feedback via an additional switch (safe switch).

V.A.G 1551 display		Possible cause	Corrective action
00932
Electric window motor, driver's side -V147-
		Faulty wiring or connectors	Check wiring and connectors using wiring diagram
		No voltage supply for central locking on driver's door	Check voltage supply to driver's door control module or to door main connector (footwell lower left) (LHD)
		Window lifter mechanical components are stiff/partially seized1)	Check window lifter mechanical components and make serviceable1)
		Driver's side window motor -V147- malfunctioning	Replace driver's side window motor -V147-
	No or incorrect adjustment	No setting for automatic opening and closing	Perform setting for automatic opening and closing. Refer to

1) It is also possible that the door window runs tight in window guides

V.A.G 1551 display		Possible cause	Corrective action
00933
Electric window motor, front passenger's side -V148-
		Faulty wiring or connectors	Check wiring and connectors using wiring diagram
		No voltage supply for central locking on front passengers door	Check voltage supply to front passenger's door control module or to door main connector (lower right footwell)
		Window lifter mechanical components are stiff/partially seized1)	Check window lifter mechanical components and make serviceable1)
		Front passenger's window motor -V148- malfunctioning	Replace front passenger's window motor -V148-
	No or incorrect adjustment	No setting for automatic opening and closing	Perform setting for automatic opening and closing. Refer to

1) It is also possible that the door window runs tight in window guides

V.A.G 1551 display		Possible cause	Corrective action
00934
Electric window motor, rear left -V26-
		Faulty wiring or connectors	Check wiring and connectors using wiring diagram
		No voltage supply for central locking on left rear door	Check voltage supply to left rear door control module or to door main connector (in left B pillar) (LHD)
		Window lifter mechanical components are stiff/partially seized1)	Check window lifter mechanical components and make serviceable1)
		Rear left window motor -V26- malfunctioning	Replace rear left window motor -V26-
	No or incorrect adjustment	No setting for automatic opening and closing	Perform setting for automatic opening and closing. Refer to

1) It is also possible that the door window runs tight in window guides

V.A.G 1551 display		Possible cause	Corrective action
00935
Electric window motor, rear right -V27-
		Faulty wiring or connectors	Check wiring and connectors using wiring diagram
		No voltage supply for central locking on right rear door	Check voltage supply to right rear door control module or to door main connector (in right B pillar) (LHD)
		Window lifter mechanical components are stiff/partially seized1)	Check window lifter mechanical components and make serviceable1)
		Rear right window motor -V27- malfunctioning	Replace rear right window motor -V27-
	No or incorrect adjustment	No setting for automatic opening and closing	Perform setting for automatic opening and closing. Refer to

1) It is also possible that the door window runs tight in window guides

V.A.G 1551 display		Possible cause	Corrective action
00936
Window lifter switch, front passenger's side -E107-1)
	Implausible signal1) Short to B+	Faulty wiring or connectors	Read Measuring Value Block; Display group number 005. Refer to Break down of display content for display group number 005 , display zone 1
		Button installation not OK., sticks when operated	Check button
		Front passenger's window lifter switch -E107- malfunctioning

1) DTC recorded if button pressed in a direction for longer than 5 minutes, or both signals (open, close) occur simultaneously.

V.A.G 1551 display		Possible cause	Corrective action
00937
Window lifter switch, rear left -E52-1)
	implausible signal Short to B+	Faulty wiring or connectors	Read Measuring Value Block; Display group number 008. Refer to Break down of display content for display group number 008 , display zone 1
		Button installation not OK., sticks when operated	Check button
		Window lifter switch, rear left -E52- malfunctioning

1) DTC recorded if button pressed in a direction for longer than 5 minutes, or both signals (open, close) occur simultaneously.

V.A.G 1551 display		Possible cause	Corrective action
00938
Window lifter switch, right rear -E54-1)
	implausible signal Short to B+	Faulty wiring or connectors	Read Measuring Value Block; Display group number 007. Refer to Break down of display content for display group number 007 , display zone 1
		Button installation not OK., sticks when operated	Check button
		Window lifter switch rear right -E54- malfunctioning

1) DTC recorded if button pressed in a direction for longer than 5 minutes, or both signals (open, close) occur simultaneously.

V.A.G 1551 display	Possible cause	Corrective action
00939
Mirror adjustment motor, driver's side -V149-
	Faulty wiring or connectors	Check wiring and connectors using wiring diagram
	No voltage supply to driver's door	Check voltage supply to driver's door control module or to door main connector (lower left footwell) (LHD)
	Driver's side mirror adjustment motor -V49- malfunctioning	Replace mirror adjustment motor, driver's side -V149-

V.A.G 1551 display	Possible cause	Corrective action
00940
Mirror adjustment motor, front passenger's side -V150-
	Faulty wiring or connectors	Check wiring and connectors using wiring diagram
	No voltage supply for central locking on front passengers door	Check voltage supply to front passenger's door control module or to door main connector (lower right footwell)
	Front passenger's side mirror adjustment motor -V150- malfunctioning	Replace mirror adjustment motor, front passenger's side -V150-

V.A.G 1551 display	Possible cause	Corrective action
00941
Exterior mirror retraction motor, driver's side -V121-
	Faulty wiring or connectors	Check wiring and connectors using wiring diagram
	No voltage supply to driver's door	Check voltage supply to driver's door control module or to door main connector (lower left footwell) (LHD)
	Exterior mirror retraction motor, driver's side -V121- malfunctioning	Replace exterior mirror retraction motor, driver's side -V121- Check exterior mirror retraction function1)

1) To do this the vehicle must be driven at [>=] 15 km/h either on a rolling road or during a test drive. The mirrors must not be retracted again. Retracting mirrors must though return to their normal position.

V.A.G 1551 display	Possible cause	Corrective action
00942
Exterior mirror retraction motor, passenger's side -V122-
	Faulty wiring or connectors	Check wiring and connectors using wiring diagram
	No voltage supply to passenger's door	Check voltage supply to passenger's door control module or to door main connector (lower right footwell) (LHD)
	Exterior mirror retraction motor, passenger's side -V122- malfunctioning	Replace exterior mirror retraction motor, passenger's side -V122- Check exterior mirror retraction function1)

1) To do this the vehicle must be driven at [>=] 15 km/h (9 mph) either on a rolling road or during a test drive. The mirrors must not be retracted again. Retracting mirrors must though return to their normal position.

V.A.G 1551 display	Possible cause	Corrective action
00943
Heated exterior mirror, driver's side -Z4-
00944
Heated exterior mirror, front passenger's side -Z5-
	Mirror heater not installed	Read Measuring Value Block; Display group number 010. Refer to Break down of display content for display group number 010 , display zone 2. Measured value block shows if rear window button is being read correctly
	Faulty wiring or connectors	Check wiring and connectors using wiring diagram
	No voltage supply to driver's/front passenger's doors	Check voltage supply to door control modules or to door main connectors (lower left and right foot wells)

V.A.G 1551 display		Possible cause	Corrective action
00946
Interior light -W-
	Short to B+	Faulty wiring or connectors	Check wiring and connectors using wiring diagram
		Interior light or one of the reading lights are malfunctioning	Replace interior light or malfunctioning reading light

V.A.G 1551 display		Possible cause	Corrective action
00947
Tailgate/trunk lid remote control switch -E188-
	Short to Ground	Faulty wiring or connectors	Check wiring and connectors using wiring diagram
		Tailgate/trunk lid remote control switch -E188- malfunctioning	Replace tailgate/trunk lid remote control switch -E188-
00948
Signal, close sliding roof
	Short to B+	Faulty wiring or connectors	Check wiring and connectors using wiring diagram

V.A.G 1551 display		Possible cause	Corrective action
00949
Motor for tailgate/trunk lid CL -V53- lock
	Undefined switch position	Faulty wiring or connectors	Check wiring and connectors using wiring diagram
		Lock mechanical components are stiff/partially seized	Check lock mechanical components and make serviceable
		Tailgate/trunk lid lock/unlock motor malfunctioning	Replace tailgate/trunk lid lock/unlock motor
00950
Motor for tailgate/trunk lid CL -V53- unlock
	Undefined switch position

V.A.G 1551 display		Possible cause	Corrective action
00951
Release for tailgate/trunk lid remote release -J398- (Only USA)
	Short to B+	Faulty wiring or connectors	Check wiring and connectors using wiring diagram
00952
Signal driver's door open
	Short to B+	Faulty wiring or connectors	Check wiring and connectors using wiring diagram

V.A.G 1551 display		Possible cause	Corrective action
00953
Time limit interior light
	Undefined switch position	Faulty wiring or connectors	Check wiring and connectors using wiring diagram
		Interior light, reading lights and luggage compartment connections malfunctioning	Check wiring and connectors using wiring diagram
		Interior light malfunctioning	Replace interior light
00954
Starter inhibitor relay -J433-1), 2)
	Short to B+	Faulty wiring or connectors	Check wiring and connectors using wiring diagram
		Starter inhibitor relay -J433- malfunctioning (USA)	Replace starter inhibitor relay -J433- (USA)

1) Not displayed on scan tool display at present

2) Only vehicles for USA or vehicles without immobilizer

V.A.G 1551 display		Possible cause	Corrective action
00955
Key 1
	Adaptation limit exceeded	Key not matched Key operated more than 200 times beyond range of system	Read Measuring Value Block; display group number 013. Refer to Break down of display content for display group number 013 , display zone 1 to 4
00956
Key 2
	Adaptation limit exceeded
00957
Key 3
	Adaptation limit exceeded
00958
Key 4
	Adaptation limit exceeded

V.A.G 1551 display		Possible cause	Corrective action
01030
Key button CL driver's side, locking
	Implausible signal	Faulty wiring or connectors	Read Measuring Value Block; Display group number 003. Refer to Break down of display content for display group number 003 , display zone 1
	Short to Ground1)	Lock cylinder sticks Faulty wiring or connectors	Check lock cylinder installation
01031
Key button CL driver's side, unlocking
	Implausible signal	Faulty wiring or connectors	Read Measuring Value Block; Display group number 003. Refer to Break down of display content for display group number 003 , display zone 1
	Short to Ground1)	Lock cylinder sticks Faulty wiring or connectors	Check lock cylinder installation

1) DTC recorded if operated for longer than 5 minutes

V.A.G 1551 display		Possible cause	Corrective action
01032
Key button CL front passenger's side, locking
	Implausible signal	Faulty wiring or connectors	Read Measuring Value Block; Display group number 006. Refer to Break down of display content for display group number 006 , display zone 1
	Short to Ground1)	Lock cylinder sticks Faulty wiring or connectors	Check lock cylinder installation
01033
Key button CL front passenger's side, unlocking
	Implausible signal		Read Measuring Value Block; Display group number 006. Refer to Break down of display content for display group number 006 , display zone 1
	Short to Ground1)

1) DTC recorded if operated for longer than 5 minutes

V.A.G 1551 display	Possible cause	Corrective action
01034
Electric window thermo protection active, driver
	Faulty wiring or connectors Electric window sticking or binding Electric window motor binding	Read Measuring Value Block; Display group number 003. Refer to Break down of display content for display group number 003 , display zone 2
01035
Electric window thermo protection active, passenger		Read Measuring Value Block; Display group number 006. Refer to Break down of display content for display group number 006 , display zone 2

V.A.G 1551 display	Possible cause	Corrective action
01036
Electric window thermo protection active, RL
	Faulty wiring or connectors Electric window sticking or binding Electric window motor binding	Read Measuring Value Block; Display group number 008. Refer to Break down of display content for display group number 008 , display zone 2
01037
Electric window thermo protection active, RR
		Read Measuring Value Block; Display group number 007. Refer to Break down of display content for display group number 007 , display zone 2

V.A.G 1551 display	Possible cause	Corrective action
01038
Central locking thermo protection
	Faulty wiring or connectors Door lock stiff	Read Measuring Value Block; Display group number 014. Refer to Break down of display content for display group number 014 , display zone 4
01044
Control module incorrectly coded
	Control module installed does not correspond to the vehicle equipment Control module supplied is not programmed or not fully programmed	Replace control module Inform part supplier of the problem

V.A.G 1551 display		Possible cause	Corrective action
01131
Turn signal activation
	Undefined switch position	Faulty wiring or connectors	Check wiring and connectors using wiring diagram Perform Output Diagnostic Test Mode (DTM). Refer to Output Diagnostic Test Mode (DTM), vehicles from 06.01 on
		Fuse S144 faulty	Check fuses using wiring diagram or replace
01134
Alarm horn -H12-
	Undefined switch position	Faulty wiring or connectors	Check wiring and connectors using wiring diagram Perform Output Diagnostic Test Mode (DTM). Refer to Output Diagnostic Test Mode (DTM), vehicles from 06.01 on
		Fuse S111 faulty	Check fuses using wiring diagram or replace
		Alarm horn -H12 malfunctioning	Replace alarm horn -H12-

V.A.G 1551 display		Possible cause	Corrective action
01135
Interior monitoring sensors
	Open circuit	Faulty wiring or connectors	Check wiring and connectors using wiring diagram Read Measuring Value Block; Display group number 009. Refer to Break down of display content for display group number 009 , display zone 4
		Sensors for monitoring interior not installed	Check installation
	Malfunctioning	Sensors for monitoring interior malfunctioning	Replace sensors for monitoring interior
01141
Luggage compartment unlocking switch -E165-
	Implausible signal	Faulty wiring or connectors Luggage compartment unlocking switch -E165- is malfunctioning	Check wiring and connectors using wiring diagram Replace luggage compartment unlocking switch -E165-

V.A.G 1551 display	Possible cause	Corrective action
01179
Incorrect key programming
	Matching of keys (function 10) not performed correctly	See description for matching keys with remote control, Adaptation Read Measuring Value Block; Display group number 013. Refer to Break down of display content for display group number 013 , display zones 1 to 41)

1) Number of keys matched ("learned") will be displayed.

V.A.G 1551 display	Possible cause	Corrective action
01328
Convenience system data BUS
	Faulty wiring or connectors	Check wiring and connectors using wiring diagram Wiring OK., then: Disconnect all door main connectors and reconnect one after the other while observing measured value block Replace the control module that has blocked the bus DTC's are stored, these must be erased Read Measuring Value Block; Display group number 012. Refer to Break down of display content for display group number 012 , display zone 1
	Control module malfunctioning	Replace relevant control module

V.A.G 1551 display	Possible cause	Corrective action
01329
Convenience system data BUS in emergency mode
	Faulty wiring or connectors	Check wiring and connectors using wiring diagram Wiring OK., then: Disconnect all door main connectors and reconnect one after the other while observing measured value block Replace the control module that has blocked the bus DTC's are stored, these must be erased Read Measuring Value Block; Display group number 012. Refer to Break down of display content for display group number 012 , display zone 1

V.A.G 1551 display		Possible cause	Corrective action
01330
Central control module for convenience system -J393-
	Malfunctioning	Central control module for convenience system malfunctioning	Replace convenience system central control module
	Voltage supply too high	Battery -A- malfunctioning or discharged Voltage regulator -C1- malfunctioning Alternator -C- malfunctioning	Check wiring and connectors using wiring diagram Read Measuring Value Block; Display group number 014. Refer to Break down of display content for display group number 014 , display zone 1
	Voltage supply too low	Battery -A- malfunctioning or discharged

V.A.G 1551 display		Possible cause	Corrective action
01331
Door control module driver's side -J386-
	Malfunctioning	Door control module, driver's side -J386 malfunctioning	Replace door control module, driver's side -J386
		Faulty wiring or connectors	Check wiring and connectors using wiring diagram
	No communication		The system, even with the DTC entry, is OK.
			Erase DTC memory
			Perform functional check
			Using Read Measuring Value Block; display group number 012. Refer to Break down of display content for display group number 012 , display zone 2, a check can be made to see if the door control module is installed or not.
	Voltage supply too high	Battery -A- malfunctioning or discharged Voltage regulator -C1- malfunctioning Alternator -C- malfunctioning	Check wiring and connectors using wiring diagram Read Measuring Value Block; Display group number 014. Refer to Break down of display content for display group number 014 , display zone 1
	Voltage supply too low	Battery -A- malfunctioning or discharged

V.A.G 1551 display		Possible cause	Corrective action
01332
Door control module, front passenger's side -J387-
	Malfunctioning	Door control module, passenger's side -J387- malfunctioning	Replace door control module, passenger's side -J387-
		Faulty wiring or connectors	Check wiring and connectors using wiring diagram
	No communication		The system, even with the DTC entry, is OK.
			Erase DTC memory
			Perform functional check
			Using Read Measuring Value Block; display group number 012. Refer to Break down of display content for display group number 012 , display zone 2, a check can be made to see if the door control module is installed or not.
	Voltage supply too high	Battery -A- malfunctioning or discharged Voltage regulator -C1- malfunctioning Alternator -C- malfunctioning	Check wiring and connectors using wiring diagram Read Measuring Value Block; Display group number 014. Refer to Break down of display content for display group number 014 , display zone 1
	Voltage supply too low

V.A.G 1551 display		Possible cause	Corrective action
01333
Door control module, rear left -J388-
	Malfunctioning	Door control module, rear left -J388- malfunctioning	Replace door control module, rear left -J388-
		Faulty wiring or connectors	Check wiring and connectors using wiring diagram
	No communication		The system, even with the DTC entry, is OK.
			Erase DTC memory
			Perform functional check
			Using Read Measuring Value Block; display group number 012. Refer to Break down of display content for display group number 012 , display zone 3, a check can be made to see if the door control module is installed or not.
	Voltage supply too high	Battery -A- malfunctioning or discharged Voltage regulator -C1- malfunctioning Alternator -C- malfunctioning	Check wiring and connectors using wiring diagram Read Measuring Value Block; Display group number 014. Refer to Break down of display content for display group number 014 , display zone 1
	Voltage supply too low

V.A.G 1551 display		Possible cause	Corrective action
01334
Door control module, rear right -J389-
	Malfunctioning	Door control module, rear right -J389- malfunctioning	Replace door control module, rear right -J389-
		Faulty wiring or connectors	Check wiring and connectors using wiring diagram
	No communication		The system, even with the DTC entry, is OK.
			Erase DTC memory
			Perform functional check
			Using Read Measuring Value Block; display group number 012. Refer to Break down of display content for display group number 012 , display zone 3, a check can be made to see if the door control module is installed or not.
	Voltage supply too high	Battery -A- malfunctioning or discharged Voltage regulator -C1- malfunctioning Alternator -C- malfunctioning	Read Measuring Value Block; Display group number 014. Refer to Break down of display content for display group number 014 , display zone 1
	Voltage supply too low

V.A.G 1551 display		Possible cause	Corrective action
01335
Driver's seat/mirror position control module 1)
	Implausible signal	Faulty wiring or connectors	Check wiring and connectors using wiring diagram Read Measuring Value Block; Display group number 012. Refer to Break down of display content for display group number 012 , display zone 4
	No communication	Seat memory control module diagnosis (no communication with door control module)1)	The seat memory is equipped with its own K wire, this can be read via address word "36"

1) Function: The control module stores the seat and mirror positions and can reset to these positions

V.A.G 1551 display		Possible cause	Corrective action
01358
Interior locking switch, driver's side -E150-
	Implausible signal	Faulty wiring or connectors	Check wiring and connectors using wiring diagram Read Measuring Value Block; Display group number 001. Refer to Break down of display content for display group number 001 , display zone 2
	Short to Ground	Faulty wiring or connectors
01359
Interior locking switch, front passenger's side -E198-
	Implausible signal	Faulty wiring or connectors	Check wiring and connectors using wiring diagram Read Measuring Value Block; Display group number 001. Refer to Break down of display content for display group number 001 , display zone 2
	Short to Ground	Faulty wiring or connectors

V.A.G 1551 display		Possible cause	Corrective action
01362
Close switch for tailgate/trunk lid -F124-2)
	Short to Ground1)	Faulty wiring or connectors	Check wiring and connectors using wiring diagram
		Lock operating mechanism or lock cylinder mechanical components binding	Check lock operating components and make serviceable Replace lock cylinder Read Measuring Value Block; Display group number 010. Refer to Break down of display content for display group number 010 , display zone 3
01389
Open switch for tailgate/trunk lid -F124- 2)
	Implausible signal
	Short to Ground1)

1) DTC recorded if operated for longer than 5 minutes

2) Unclip contact switch on lock cylinder housing (with small lever)

V.A.G 1551 display		Possible cause	Corrective action
01483
Activation of rear lid remote unlocking
	Undefined switch position	Faulty wiring or connectors	Check wiring and connectors using wiring diagram
01484
Central locking key button, lock
	Short to Ground1)	Faulty wiring or connectors	Check wiring and connectors using wiring diagram
01485
Central locking key button, unlock
	Short to Ground1)	Faulty wiring or connectors	Check wiring and connectors using wiring diagram

1) DTC recorded if operated for longer than 10 seconds