Section 27 (4 SPD. Automatic Transmission 01M (A4 Platform))
WARNING: This page is about a different variant/trim than selected.
- 00 General, Technical data
- 32 Torque converter
- 37 Automatic Transmission - Controls, Housing
- Electrical/electronic components / locations
- Gear change mechanism, servicing
- Gear change mechanism, servicing
- Gear change mechanism, checking
- Selector lever cable, checking and adjusting
- Checking operation of the ignition key withdrawal lock
- Selector mechanism, disassembling and assembling
- Shift lock solenoid -N110-, removing and installing
- Selector lever cable, removing and installing
- Selector lever, removing and installing
- Locking cable, removing and installing
- Locking cable, adjusting
- Transmission, checking
- Transmission, removing and installing
- ATF level, checking and topping up
- Transmission with selector elements
- Transmission, disassembling and assembling
- Transmission, disassembling and assembling
- ATF cooler and ATF filler tube, removing and installing
- Planetary gearbox, disassembling and assembling -Overview-
- I - ATF pump to supporting tube, removing and installing
- II - Reverse gear clutch -K2- to large sun gear, removing and installing
- III - Freewheel and reverse gear brake -B1-, removing and installing
- IV - Planet carrier and transmission housing with input gear and cover
- Planetary gearbox, disassembling and assembling
- Overview of all planetary gearbox adjustments
- Planet carrier, adjustments
- Reverse gear brake -B1-, adjusting
- Clutch play between -K1- and -K2-, adjusting
- 2nd and 4th gear brake -B2-, adjusting
- 38 Automatic Transmission - Gears, Hydraulic controls
- Solenoid Valves in Valve Body, Checking
- Vehicle Speed Sensor G68, Checking
- Transmission Vehicle Speed Sensor G38, Checking
- Multi-Function Transmission Range Switch F125, Checking
- Transmission Control Module J217, Replacing
- ATF pump, disassembling and assembling
- Freewheel with -B1- piston, disassembling and assembling
- 1st to 3rd gear clutch -K1-, disassembling and assembling
- Reverse gear clutch -K2-, disassembling and assembling
- 3rd and 4th gear clutch -K3- with turbine shaft, disassembling and assembling
- Valve body, removing and installing
- Valve body, removing and installing
- Notes
- Draining ATF
- Replacing plug seal
- Removing conductor strip
- Removing valve body/unhooking operating rod
- Inserting sealing plug
- Identification of valve body
- Hooking operating rod onto manual selector valve
- Adjusting operating rod for manual selector valve
- Installing valve body
- Installing ATF screen
- Installing securing clip with bolt for conductor strip connector
- Valve body, removing and installing
- Parking lock, disassembling and assembling
- Parking lock, disassembling and assembling
- Notes
- Driving spring pins (arrows) out and in
- Removing and installing selector shaft with selector segments
- Inserting guide plate and supporting plate
- Inserting pawl with return spring
- Pulling out starter bushing
- Driving in starter bushing
- Removing and installing Multi-function TR switch -F125-
- Removing and installing Transmission vehicle speed sensor -G38-
- Removing and installing Vehicle speed sensor -G68- with transmission installed
- Parking lock, disassembling and assembling
- 39 Final drive, Differential
- Final drive oil, checking
- Axle flange seal, removing and installing
- Final drive, disassembling and assembling
- Repair overview of final drive
- Input gear, removing and installing
- Drive pinion, removing and installing
- Notes
- Pulling off output gear
- Pulling off tapered roller bearing inner race
- Pressing on tapered roller bearing inner race
- Pressing in tapered roller bearing outer race
- Removing and installing bearing supporting ring
- Bearing supporting ring with seal for drive pinion
- Driving in drive pinion oil seal
- Removing drive pinion
- Driving in tapered roller bearing outer race
- Differential, removing and installing
- Differential, disassembling and assembling
- Final drive, adjusting