DTC table
WARNING: This page does not describe the selected car, but rather 26 other vehicles, including the 2009 Volkswagen Golf, 2008 Volkswagen Golf, 2007 Volkswagen Golf, 2006 Volkswagen Golf, and 2006 Volkswagen GTI. However, it is still accessible from the selected car via links, so may be relevant.
Scan tool print-out: The number shown here in bold 049 (e.g.) has no relevance.
01333 049 Door CU -J388 no communication |
| V.A.G 1551 display |
Possible cause |
Corrective action |
| 00000 |
|
|
| No DTC recognized |
If "No DTC recognized" appears after carrying out repairs On Board Diagnostic (OBD) is ended |
| 00668 |
|
|
| Vehicle voltage terminal 30 |
|
|
| |
Signal too small |
|
|
| |
- Faulty wiring or connectors
|
- Check wiring and connectors using wiring diagram
|
| V.A.G 1551 display |
Possible cause |
Corrective action |
| 00849 |
|
|
| S-terminal on ignition/starter switch -D- |
|
|
| |
Undefined switch condition |
- Terminal 15 OK. but S-terminal faulty
|
|
| |
- Faulty wiring or connectors
|
|
| V.A.G 1551 display |
Possible cause |
Corrective action |
| 00928 |
|
|
| Locking unit for driver's side CL -F220- |
|
|
| |
Implausible signal |
- Faulty wiring or connectors
|
- Check wiring and connectors using wiring diagram
|
| |
- No voltage supply for central locking on driver's door
|
- Check voltage supply to driver's door control module or to door main connector (lower left footwell)
|
| |
- Lock unit mechanics and operating components are stiff/partially seized
|
- Check lock unit mechanical components and operating components and make serviceable
|
| |
- Locking unit for driver's side central locking -F220- malfunctioning
|
- Replace locking unit for driver's door central locking -F220-
|
| |
Wrong equipment |
- Wrong locking unit installed1)
|
|
1) If a rest of world lock is installed in a USA vehicle, there is a safe feedback via an additional switch (safe switch).
| V.A.G 1551 display |
Possible cause |
Corrective action |
| 00929 |
|
|
| Locking unit for front passenger's side CL -F221- |
|
|
| |
Implausible signal |
- Faulty wiring or connectors
|
- Check wiring and connectors using wiring diagram
|
| |
- No voltage supply for central locking on front passengers door
|
- Check voltage supply to front passenger's door control module or to door main connector (lower right footwell)
|
| |
- Lock unit mechanics and operating components are stiff/partially seized
|
- Check lock unit mechanical components and operating components and make serviceable
|
| |
- Locking unit for front passenger's central locking -F221- malfunctioning
|
- Replace locking unit for front passenger's door central locking -F221-
|
| |
Wrong equipment |
- Wrong locking unit installed1)
|
|
1) If a rest of world lock is installed in a USA vehicle, there is a safe feedback via an additional switch (safe switch).
| V.A.G 1551 display |
Possible cause |
Corrective action |
| 00930 |
|
|
| Locking unit for rear left CL -F222- |
|
|
| |
Implausible signal |
- Faulty wiring or connectors
|
- Check wiring and connectors using wiring diagram
|
| |
- No voltage supply for central locking on rear left door
|
- Check voltage supply to rear left door control module or to door main connector (in B pillar left)
|
| |
- Lock unit mechanics and operating components are stiff/partially seized
|
- Check lock unit mechanical components and operating components and make serviceable
|
| |
- Locking unit for rear left central locking -F222- malfunctioning
|
- Replace locking unit for rear left central locking -F222-
|
| |
Wrong equipment |
- Wrong locking unit installed1)
|
|
1) If a rest of world lock is installed in a USA vehicle, there is a safe feedback via an additional switch (safe switch).
| V.A.G 1551 display |
Possible cause |
Corrective action |
| 00931 |
|
|
| Locking unit for rear right CL -F223- |
|
|
| |
Implausible signal |
- Faulty wiring or connectors
|
- Check wiring and connectors using wiring diagram
|
| |
- No voltage supply for central locking on rear right door
|
- Check voltage supply to rear right door control module or to door main connector (in B pillar right)
|
| |
- Lock unit mechanics and operating components are stiff/partially seized
|
- Check lock unit mechanical components and operating components and make serviceable
|
| |
- Locking unit for rear right central locking -F223- malfunctioning
|
- Replace locking unit for rear right central locking -F223-
|
| |
Wrong equipment |
- Wrong locking unit installed1)
|
|
1) If a rest of world lock is installed in a USA vehicle, there is a safe feedback via an additional switch (safe switch).
| V.A.G 1551 display |
Possible cause |
Corrective action |
| 00945 |
|
|
| Crash sensor for front airbag -G190- |
|
|
| |
Short to Ground |
- Faulty wiring or connectors
|
- Check wiring and connectors using wiring diagram
- Output can also be checked using Output Diagnostic Test Mode (DTM) for airbag. Refer to Output Diagnostic Test Mode (DTM)
|
| 00946 |
|
|
| Interior light -W- |
|
|
| |
Short to B+ |
- Faulty wiring or connectors
|
- Check wiring and connectors using wiring diagram
|
| |
|
- Interior light or one of the reading lights are malfunctioning
|
- Replace interior light or malfunctioning reading light
|
| V.A.G 1551 display |
Possible cause |
Corrective action |
| 00947 |
|
|
| Tailgate/trunk lid remote control switch -E188- |
|
|
| |
Short to Ground |
- Faulty wiring or connectors
|
- Check wiring and connectors using wiring diagram
|
| |
|
- Tailgate/trunk lid remote control switch -E188- malfunctioning
|
- Replace tailgate/trunk lid remote control switch -E188-
|
| V.A.G 1551 display |
Possible cause |
Corrective action |
| 00949 |
|
|
| Motor for tailgate/trunk lid CL lock |
|
|
| |
Undefined switch position |
- Faulty wiring or connectors
|
- Check wiring and connectors using wiring diagram
|
| |
- Lock mechanical components are stiff/partially seized
|
- Check lock mechanical components and make serviceable
|
| |
|
- Tailgate/trunk lid lock/unlock motor malfunctioning
|
- Replace tailgate/trunk lid lock/unlock motor
|
| 00950 |
|
|
| Motor for tailgate/trunk lid CL unlock |
|
|
| |
Undefined switch position |
|
|
| 00951 |
|
|
| Release for tailgate/trunk lid remote release -J398- (Only USA) |
|
|
| |
Short to B+ |
- Faulty wiring or connectors
|
- Check wiring and connectors using wiring diagram
|
| V.A.G 1551 display |
Possible cause |
Corrective action |
| 00953 |
|
|
| Time limit interior light |
|
|
| |
Undefined switch position |
- Faulty wiring or connectors
|
- Check wiring and connectors using wiring diagram
|
| |
|
- Interior light, reading lights and luggage compartment connections malfunctioning
|
- Check wiring and connectors using wiring diagram
|
| |
|
- Interior light malfunctioning
|
|
| 00954 |
|
|
| Starter inhibitor relay -J433-1), 2) |
|
|
| |
Short to B+ |
- Faulty wiring or connectors
|
- Check wiring and connectors using wiring diagram
|
| |
|
- Starter inhibitor relay -J433- malfunctioning (USA)
|
- Replace starter inhibitor relay -J433- (USA)
|
1) Not displayed on scan tool display at present
2) Only vehicles for USA or vehicles without immobilizer
| V.A.G 1551 display |
Possible cause |
Corrective action |
| 00955 |
|
|
| Key 1 |
|
|
| |
Adaptation limit exceeded |
- Key not matched
- Key operated more than 200 times beyond range of system
|
|
| 00956 |
|
|
| Key 2 |
|
|
| |
Adaptation limit exceeded |
|
|
| 00957 |
|
|
| Key 3 |
|
|
| |
Adaptation limit exceeded |
|
|
| 00958 |
|
|
| Key 4 |
|
|
| |
Adaptation limit exceeded |
|
|
| V.A.G 1551 display |
Possible cause |
Corrective action |
| 01030 |
|
|
| CL key button driver's side, locking |
|
|
| |
Implausible signal |
- Faulty wiring or connectors
|
|
| |
Short to Ground1) |
- Lock cylinder sticks
- Faulty wiring or connectors
|
- Check lock cylinder installation
|
| 01031 |
|
|
| CL key button driver's side, unlocking |
|
|
| |
Implausible signal |
- Faulty wiring or connectors
|
|
| |
Short to Ground1) |
- Lock cylinder sticks
- Faulty wiring or connectors
|
- Check lock cylinder installation
|
1) Malfunction recorded if operated for longer than 5 minutes
| V.A.G 1551 display |
Possible cause |
Corrective action |
| 01032 |
|
|
| CL key button passenger's side, locking |
|
|
| |
Implausible signal |
- Faulty wiring or connectors
|
|
| |
Short to Ground1) |
- Lock cylinder sticks
- Faulty wiring or connectors
|
- Check lock cylinder installation
|
| 01033 |
|
|
| CL key button passenger's side, unlocking |
|
|
| |
Implausible signal |
- Faulty wiring or connectors
|
|
| |
Short to Ground1) |
- Lock cylinder sticks
- Faulty wiring or connectors
|
- Check lock cylinder installation
|
1) Malfunction recorded if operated for longer than 5 minutes
| V.A.G 1551 display |
Possible cause |
Corrective action |
| 01038 |
|
|
| Central locking thermo protection |
|
|
| |
|
- Faulty wiring or connectors
- Door locks stiff
|
|
| 01044 |
|
|
| Control module incorrectly coded |
|
|
| |
|
- The control module installed does not correspond to the vehicle equipment
- Control module supplied is not programmed or not completely programmed
|
- Replace control module
- Inform spare part supplier of the problem
|
| V.A.G 1551 display |
Possible cause |
Corrective action |
| 01131 |
|
|
| Turn signal activation |
|
|
| |
Undefined switch position |
- Faulty wiring or connectors
|
|
| |
|
|
- Check fuses using wiring diagram or replace
|
| 01134 |
|
|
| Alarm horn -H12- |
|
|
| |
Undefined switch position |
- Faulty wiring or connectors
|
|
| |
|
|
- Check fuses using wiring diagram or replace
|
| |
|
- Alarm horn -H12- malfunctioning
|
|
| V.A.G 1551 display |
Possible cause |
Corrective action |
| 01135 |
|
|
| Interior monitoring sensors |
|
|
| |
Open circuit |
- Faulty wiring or connectors
|
- Check wiring and connectors using wiring diagram
|
| |
|
- Sensors for monitoring interior not installed
|
|
| |
Malfunctioning |
- Sensors for monitoring interior malfunctioning
|
- Replace sensors for monitoring interior
|
| 01141 |
|
|
| Tailgate unlocking switch -E165- |
|
|
| |
Implausible signal |
- Faulty wiring or connectors
- Tailgate unlocking switch -E165- is malfunctioning
|
- Check wiring and connectors using wiring diagram
- Replace tailgate unlocking switch -E165-
|
| V.A.G 1551 display |
Possible cause |
Corrective action |
| 01179 |
|
|
| Incorrect key programming |
|
|
| |
|
- Adaptation of keys (function 10) not performed correctly
|
|
| 01355 |
|
|
| Signal; All windows open |
|
|
| |
Short to B+ |
- Faulty wiring or connectors
|
- Check wiring and connectors using wiring diagram
|
| |
- Lock operating or lock cylinder mechanical components stiff
|
- Check lock operating components and make serviceable
- Replace lock cylinder
|
| V.A.G 1551 display |
Possible cause |
Corrective action |
| 01356 |
|
|
| Signal; Close all windows and sliding/tilting roof |
|
|
| |
Short to B+ |
- Faulty wiring or connectors
|
- Check wiring and connectors using wiring diagram
|
| |
- Lock operating or lock cylinder mechanical components stiff
|
- Check lock operating components and make serviceable
- Replace lock cylinder
|
| V.A.G 1551 display |
Possible cause |
Corrective action |
| 01362 |
|
|
| Close switch for tailgate/trunk lid -F124-2) |
|
|
| |
Short to Ground1) |
- Faulty wiring or connectors
|
- Check wiring and connectors using wiring diagram
|
| |
- Lock operating or lock cylinder mechanical components stiff
|
- Check lock operating components and make serviceable
- Replace lock cylinder
|
| 01365 |
|
|
| Lock/Unlock switch/interior lock button |
|
|
| |
Short to Ground1) |
- Faulty wiring or connectors
|
- Check wiring and connectors using wiring diagram
|
| |
|
- Driver's interior locking switch is malfunctioning
|
- Replace driver's interior locking switch
|
1) Malfunction recorded if operated for longer than 5 minutes
2) Unclip contact switch on lock cylinder housing (with small lever)
| V.A.G 1551 display |
Possible cause |
Corrective action |
| 01389 |
|
|
| Open switch for tailgate/trunk lid -F124-2) |
|
|
| |
Short to Ground1) |
- Faulty wiring or connectors
|
- Check wiring and connectors using wiring diagram
|
| |
- Lock operating or lock cylinder mechanical components stiff
|
- Check lock operating components and make serviceable
- Replace lock cylinder
|
1) Malfunction recorded if operated for longer than 5 minutes
2) Unclip contact switch on lock cylinder housing (with small lever)