LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2025 >> RAV4 Plug-In Hybrid XSE >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 224 (Engine Mechanical System (A25A-FKS) - Service Information (2 Of 6)) >> Rear Crankshaft Oil Seal >> Installation [11/2018 - ] >> Procedure

Installation [11/2018 - ]: Procedure

WARNING: This page is about a different variant/trim than selected.
  1. INSTALL REAR ENGINE OIL SEAL 
    1. Using height adjustment attachments and plate lift attachments, place the engine assembly on a flat level surface.
      NOTE:
      • Using height adjustment attachments and plate lift attachments, keep the engine assembly level.
      • To prevent the No. 2 oil pan sub-assembly from deforming, do not place any attachments under the No. 2 oil pan sub-assembly of the engine assembly.
      • Using an engine sling device and engine lift, secure the engine assembly before servicing.
    2. Apply MP grease to the lip of a new rear engine oil seal.
      NOTE:
      • Keep the lip free from foreign matter.
      • Do not allow MP grease to contact the dust seal.
    3. Using SST and a hammer, tap in the rear engine oil seal.
      GTY751431Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a -0.9 to 1.1 mm
      • SST: 09223-15030 
      • SST: 09950-70010 
        1. 09951-07150

      Standard Depth

      -0.9 to 1.1 mm (-0.0354 to 0.0433 in.) (From the edge of the cylinder block sub-assembly and stiffening crankcase assembly)

      NOTE:

      Do not tap in the rear engine oil seal at an angle.

  2. INSTALL NO. 1 CRANKSHAFT POSITION SENSOR PLATE 
    1. Install the No. 1 crankshaft position sensor plate.

      HINT: 

      Align the pin hole of the No. 1 crankshaft position sensor plate with the pin of the crankshaft.

      GTY756894Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  3. INSTALL DRIVE PLATE AND RING GEAR SUB-ASSEMBLY 
    1. Using SST, hold the crankshaft pulley assembly.
      GTY749031Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      • SST: 09213-54015 
      • SST: 09330-00021 
    2. Clean the 8 bolts and bolt holes.
    3. Install the drive plate and ring gear sub-assembly and rear drive plate spacer to the crankshaft.
      GTY768547Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 Drive Plate and Ring Gear Sub-assembly
      *2 Rear Drive Plate Spacer
      *3 No. 1 Crankshaft Position Sensor Plate
      Transaxle Side
      NOTE:

      As the rear drive plate spacer, drive plate and ring gear sub-assembly and No. 1 crankshaft position sensor plate are not reversible, be sure to install them so that they are facing in the direction shown in the illustration.

    4. Apply a few drops of adhesive to 2 or 3 threads at the tip of each of 8 bolts.
      GTY445334Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Adhesive

      Adhesive

      Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

    5. Install and uniformly tighten the 8 bolts in the sequence shown in the illustration.
      Fig 1: Drive Plate And Ring Gear Sub-Assembly Tightening Sequence
      GTY747266Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Torque: 150 N*m (1530 kgf*cm, 111 ft.*lbf) 

      NOTE:
      • Do not reuse the drive plate installation bolts.
      • Handle the drive plate installation bolts carefully. Do not scratch them or subject them to any shocks.
      • Do not start the engine for at least 1 hour after installing the drive plate and ring gear sub-assembly.
  4. INSTALL AUTOMATIC TRANSAXLE ASSEMBLY 
scientia non olet · About LEMON Manuals