Installation [12/2021 - ]: Procedure

WARNING: This page is about a different variant/trim than selected.

INSTALL FRONT BUMPER EXTENSION SUB-ASSEMBLY LH

Install the front bumper extension sub-assembly LH with the 2 nuts and 2 bolts.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

	Bolt A
	Bolt B
	Nut

for Bolt A

Torque: 135 N.m (1377 kgf/cm, 100 ft.lbf)

for Bolt B

Torque: 9.5 N.m (97 kgf/cm, 84 in.lbf)

for Nut

Torque: 12.5 N.m (127 kgf/cm, 9 ft.lbf)

INSTALL FRONT BUMPER EXTENSION SUB-ASSEMBLY RH
HINT:

Use the same procedure as for the RH and LH sides.

INSTALL FRONT BUMPER SEAL (for TMMC Made)

HINT:

When installing a new front bumper seal, heat the front bumper lower absorber using a heat light.

Standard

Item	Temperature
Front Bumper Lower Absorber	20 to 30°C (68 to 86°F)

WARNING:

Do not touch the heat light and heated parts.
Touching the heat light may result in burns.
Touching heated parts for a long time may result in burns.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

*a	Heated Part
*b	Heat Light

NOTE:

Do not heat the front bumper lower absorber excessively.

When reusing the front bumper lower absorber:
1. Using a heat light, heat the front bumper lower absorber surface.
2. Remove any remaining double-sided tape from the front bumper lower absorber.
3. Wipe off any tape adhesive residue with cleaner.
  NOTE:
  - Installing the front bumper seal with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.
  - Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.
  - Clean a new front bumper lower absorber surface.
Remove the release paper of a new front bumper seal trying not to touch the adhesional surface.
HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.

Align 2 new front bumper seals with the mark-off line and rib on the front bumper lower absorber and install it.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

*A	for HV Model	*B	for Gasoline Model
*a	Mark-off Line	*b	Rib

INSTALL FRONT BUMPER LOWER ABSORBER (for HV Model)

Attach the claw to install the front bumper lower absorber as shown in the illustration.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

Install in this Direction

Install the clip.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

INSTALL FRONT BUMPER LOWER ABSORBER (for Gasoline Model)

Attach the guide and install the front bumper lower absorber as shown in the illustration.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

Install in this Direction

Install the 5 bolts.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

INSTALL NO. 1 ENGINE UNDER COVER

Attach the guide to install the No. 1 engine under cover.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

Install in this Direction

for Gasoline Model:

Install the 2 bolts and 2 Screws.

for Bolt

Torque: 7.5 N.m (76 kgf/cm, 66 in.lbf)

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

*A	for Short Front Fender Front Splash Shield	-	-
	Bolt		Screw

for HV Model:

Install the 2 bolts.

for Bolt

Torque: 7.5 N.m (76 kgf/cm, 66 in.lbf)

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

*A	for Short Front Fender Front Splash Shield	*B	for Type B:
	Bolt		Screw

for Short Front Fender Front Splash Shield:
Install the 2 screws.
for Type B:
Install the 2 screws.

INSTALL FRONT BUMPER NO. 2 REINFORCEMENT (for HV Model)

Install the front bumper No. 2 reinforcement with the 4 nuts.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

Torque: 18 N.m (184 kgf/cm, 13 ft.lbf)

INSTALL FRONT BUMPER REINFORCEMENT SUB-ASSEMBLY

Install the front bumper reinforcement sub-assembly with the 6 bolts as shown in the illustration.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

Install in this Direction

Torque: 43 N.m (438 kgf/cm, 32 ft.lbf)

Attach the wire harness clamp.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

INSTALL FRONT BUMPER NO. 2 ENERGY ABSORBER

Attach the guide and install the front bumper No. 2 energy absorber.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

Install in this Direction

INSTALL FRONT BUMPER SIDE RETAINER LH

Attach the clip and claw to install the front bumper side retainer LH as shown in the illustration.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

Install in this Direction

Install the bolt.

INSTALL FRONT BUMPER SIDE RETAINER RH
HINT:

Use the same procedure described for the LH side.

INSTALL FRONT BUMPER ASSEMBLY

Install 2 new clips to the front fender moulding sub-assembly LH.

NOTE:

If the front bumper assembly has been removed, replace the clip with a new one.

HINT:

Use the same procedure as for the RH and LH sides.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

Attach the claw to temporarily install the front bumper assembly.

Install in this Direction

Connect the 2 connectors.

Install the front bumper assembly to the front bumper side retainer LH.

Make sure that the front bumper assembly claw contacts the front bumper side retainer LH as shown in the illustration.

*1	Front Fender Panel
*2	Front Bumper Side Retainer LH
*3	Front Bumper Assembly
*a	Correct
*b	Incorrect

Attach the claw to install the front bumper assembly as shown in the illustration.

Install in this Direction

HINT:

Use the same procedure as for the RH and LH sides.

After installation, if there is a clearance and the front bumper assembly claw can be seen as shown in the illustration, the installation condition is incorrect. Perform the procedure from step 1 again.

Correct

Incorrect

Install the 2 clips.

HINT:

Use the same procedure as for the RH and LH sides.

Install the 6 screws.

Install the 4 bolts.

Remove the protective tape.

INSTALL FRONT FENDER MOULDING SUB-ASSEMBLY LH

Attach the clip and claw to install the front fender moulding sub-assembly LH.

Install in this Direction

Remove the protective tape.

Install the 2 clips.

	Screw
	Clip

Install the screw.

INSTALL FRONT FENDER MOULDING SUB-ASSEMBLY RH
HINT:

Use the same procedure as for the LH side.
INSTALL FRONT FENDER FRONT SPLASH SHIELD LH
HINT:

Use the same procedure described for the RH side.
1. for Short Type:
  Refer to PROCEDURE - Step 13
2. for Long Type:
  Refer to PROCEDURE - Step 12
INSTALL FRONT FENDER FRONT SPLASH SHIELD RH
HINT:

Use the same procedure described for the LH side.
ADJUST FOG LIGHT ASSEMBLY (w/ Fog Light)
Refer to ADJUSTMENT [12/2021 - ]
ADJUST FRONT TELEVISION CAMERA ASSEMBLY (w/ Panoramic View Monitor System)
1. for HV Model:
  Refer to CALIBRATION [11/2018 - 10/2022] , or refer to CALIBRATION [10/2022 - ]
2. for Gasoline Model:
  Refer to CALIBRATION [11/2018 - 10/2022] , or refer to CALIBRATION [10/2022 - ]