LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2025 >> RAV4 Plug-In Hybrid XSE >> Repair and Diagnosis >> Body & Frame >> Exterior/Interior Trim >> Interior Panels / Trim - Service Information (2 Of 2) (PHEV) >> Roof Headlining >> Removal [06/2020 - 12/2021] >> Procedure

Removal [06/2020 - 12/2021]: Procedure

  1. REMOVE TONNEAU COVER ASSEMBLY (w/ Tonneau Cover) 
    1. Remove the tonneau cover assembly.
      GTY1009379Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  2. REMOVE DECK BOARD ASSEMBLY 
    1. Remove the deck board assembly.
      GTY1009377Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  3. REMOVE REAR NO. 3 FLOOR BOARD 
    1. Detach the clip and guide and remove the rear No. 3 floor board.
      GTY1007937Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  4. REMOVE SPARE WHEEL COVER STOPPER 
    1. Remove the spare wheel cover stopper.
      GTY1008623Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  5. REMOVE BENCH TYPE REAR SEAT CUSHION ASSEMBLY 

    Refer to PROCEDURE - Step 1

  6. REMOVE REAR SEAT CUSHION LOCK HOOK 

    Refer to PROCEDURE - Step 2

  7. REMOVE REAR DOOR SCUFF PLATE LH 
    1. Place your hand at the position shown in the illustration and pull in the removal direction to detach the claw and guide.
      GTY882899Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Place Hand Here
      Remove in this Direction
    2. Place both hands at the position shown in the illustration and lift in the direction indicated by the arrow to detach the clamp, claw and clip and remove the rear door scuff plate LH.
      GTY898055Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Place Hands Here
      Remove in this Direction
  8. REMOVE REAR DOOR SCUFF PLATE RH 

    HINT: 

    Use the same procedure described for the LH side.

  9. REMOVE REAR FLOOR FINISH PLATE 
    1. Detach the claw, clip and guide and remove the rear floor finish plate.
      GTY1007907Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  10. REMOVE REAR SEATBACK ASSEMBLY LH 

    Refer to PROCEDURE - Step 3

  11. REMOVE REAR CENTER SEAT OUTER BELT ASSEMBLY (FLOOR ANCHOR) 

    Refer to PROCEDURE - Step 3

  12. REMOVE REAR SEATBACK ASSEMBLY RH 

    Refer to PROCEDURE - Step 5

  13. REMOVE NO. 3 BATTERY SERVICE COVER BOARD 

    Refer to PROCEDURE - Step 9

  14. REMOVE NO. 2 BATTERY SERVICE COVER BOARD 

    Refer to PROCEDURE - Step 11

  15. REMOVE BATTERY SERVICE COVER BOARD 

    Refer to PROCEDURE - Step 12

  16. REMOVE REAR SEATBACK HINGE SUB-ASSEMBLY LH 

    Refer to PROCEDURE - Step 7

  17. REMOVE REAR SEATBACK HINGE SUB-ASSEMBLY RH 

    HINT: 

    Use the same procedure described for the LH side.

  18. REMOVE CHILD RESTRAINT SEAT ANCHOR BRACKET SUB-ASSEMBLY LH 

    Refer to PROCEDURE - Step 6

  19. REMOVE CHILD RESTRAINT SEAT ANCHOR BRACKET SUB-ASSEMBLY RH 

    HINT: 

    Use the same procedure described for the LH side.

  20. REMOVE REAR NO. 1 FLOOR MAT SUPPORT SIDE PLATE 
    1. Remove the 2 screws.
      GTY1007905Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Detach the clip and claw and remove the rear No. 1 floor mat support side plate.
  21. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH 

    Refer to PROCEDURE - Step 2

  22. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH 

    HINT: 

    Use the same procedure described for the LH side.

  23. REMOVE FRONT DOOR SCUFF PLATE LH 
    1. Place your hand at the position shown in the illustration and pull in the removal direction to detach the claw and guide.
      GTY938099Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Place Hand Here
      Remove in this Direction
    2. Place both hands at the position shown in the illustration and lift in the direction indicated by the arrow to detach the clamp and claw and remove the front door scuff plate LH.
      GTY910439Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Place Hands Here
      Remove in this Direction
  24. REMOVE FRONT DOOR SCUFF PLATE RH 

    HINT: 

    Use the same procedure described for the LH side.

  25. REMOVE COWL SIDE TRIM BOARD LH 

    Refer to PROCEDURE - Step 14

  26. REMOVE COWL SIDE TRIM BOARD RH 

    HINT: 

    Use the same procedure described for the LH side.

  27. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH 

    Refer to PROCEDURE - Step 3

  28. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH 

    HINT: 

    Use the same procedure described for the LH side.

  29. REMOVE FRONT PILLAR GARNISH LH 
    1. Place your hand at the position shown in the illustration and pull in the direction indicated by the arrow to detach the front pillar garnish clip.
      GTY943899Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Place Hand Here
      Remove in this Direction
    2. Push in the release lever with your finger and remove the front pillar garnish clip from the vehicle.
      GTY846194Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Release Lever
      Push
    3. When the front pillar garnish clip cannot be detached by pressing the knobs with the fingers:
      1. GTY829714Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        Direction (A)
        Push

        Lift up the front pillar garnish clip in the direction (A) while pressing the portion indicated by the arrow in the illustration with your fingers.

      2. GTY795374Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        Direction (B)
        Release Lever
        Push

        Push in the portion indicated by the arrow in the illustration with the screwdriver end while pulling the front pillar garnish clip with your fingers in the direction (B) to detach the front pillar garnish clip.

    4. Place your hand at the position shown in the illustration and pull in the direction indicated by the arrow to detach the front pillar garnish clip.
      GTY915510Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Place Hand Here
      Remove in this Direction
    5. Push in the release lever with your finger and remove the front pillar garnish clip from the vehicle.
      GTY855570Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Release Lever
      Push
    6. When the front pillar garnish clip cannot be detached by pressing the knobs with the fingers:
      1. GTY829714Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        Direction (A)
        Push

        Lift up the front pillar garnish clip in the direction (A) while pressing the portion indicated by the arrow in the illustration with your fingers.

      2. GTY795374Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        Direction (B)
        Release Lever
        Push

        Push in the portion indicated by the arrow in the illustration with the screwdriver end while pulling the front pillar garnish clip with your fingers in the direction (B) to detach the front pillar garnish clip.

    7. Pull in the direction of the arrow shown in the illustration to detach the guide and remove the front pillar garnish LH.
      GTY840854Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Remove in this Direction
    8. for 9 Speakers:
      1. Disconnect the connector.
        GTY919554Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    9. Protect curtain shield airbag assembly:
      GTY850689Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Protective Cover
      Adhesive Tape
      1. Cover the airbag with a cloth or piece of nylon and secure both ends of the cover with adhesive tape as shown in the illustration.
        NOTE:

        Cover the curtain shield airbag assembly with a protective cover as soon as the front pillar garnish assembly LH is removed.

  30. REMOVE FRONT PILLAR GARNISH RH 

    HINT: 

    Use the same procedure described for the LH side.

  31. REMOVE OUTER LAP BELT ANCHOR COVER 

    HINT: 

    Use the same procedure for both outer lap belt anchor covers.

    1. Detach the claw and guide and remove the outer lap belt anchor cover.
      GTY919491Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  32. REMOVE FRONT SEAT OUTER BELT ASSEMBLY LH 
    1. Remove the bolt and remove the front seat outer belt assembly LH.
      GTY944117Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  33. REMOVE FRONT SEAT OUTER BELT ASSEMBLY RH 

    HINT: 

    Use the same procedure described for the LH side.

  34. REMOVE LOWER CENTER PILLAR GARNISH LH 
    1. Pull both sides of the lower center pillar garnish LH outward to detach the claw as shown in the illustration.
      GTY920789Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Place Hands Here
      Remove in this Direction
    2. Detach the clip and remove the lower center pillar garnish LH.
  35. REMOVE LOWER CENTER PILLAR GARNISH RH 

    HINT: 

    Use the same procedure described for the LH side.

  36. REMOVE CENTER PILLAR GARNISH LH 
    1. Remove the 2 clips.
      GTY855566Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Place Hands Here
      Remove in this Direction
    2. Place both hands at the position shown in the illustration, detach the clip and remove the center pillar garnish LH.
    3. When reusing the center pillar garnish LH:
      1. Remove the clip.
        GTY913464Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  37. REMOVE CENTER PILLAR GARNISH RH 

    HINT: 

    Use the same procedure described for the LH side.

  38. REMOVE REAR SEAT SIDE GARNISH LH 
    1. Place your hand at the position shown in the illustration, and detach the claw.
      GTY1010418Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Place Hand Here
      Remove in this Direction
    2. Detach the clip and claw and remove the rear seat side garnish LH as shown in the illustration.
      GTY1011311Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Remove in this Direction
  39. REMOVE REAR SEAT SIDE GARNISH RH 

    HINT: 

    Use the same procedure described for the LH side.

  40. REMOVE TETHER ANCHOR BRACKET SET 

    HINT: 

    Use the same procedure for the opposite side.

    1. Detach the claw and turn the cover up as shown in the illustration.
      GTY1011517Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Turn Up in this Direction
    2. Loosen the bolt and remove the tether anchor bracket set.
      GTY1010925Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  41. REMOVE LUGGAGE HOLD BELT STRIKER ASSEMBLY 

    HINT: 

    Use the same procedure for the opposite side.

    1. Remove the bolt.
      GTY1011022Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Detach the guide and remove the luggage hold belt striker assembly.
  42. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH 
    1. Remove the clip.
    2. except "TORX" Screw:
      1. Remove the screw.
    3. for "TORX" Screw:
      1. Using a T30 "TORX" socket wrench, remove the "TORX" screw.
    4. Detach the clip, claw and guide and remove the deck trim side panel assembly LH.
      GTY1011067Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Clip Screw or "TORX" Screw
  43. REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH 
    1. Remove the clip.
    2. except "TORX" Screw:
      1. Remove the screw.
    3. for "TORX" Screw:
      1. Using a T30 "TORX" socket wrench, remove the "TORX" screw.
    4. Detach the clip, claw and guide and remove the deck trim side panel assembly RH.
      GTY1008466Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Clip Screw or "TORX" Screw
    5. Disconnect each connector.
  44. REMOVE INNER ROOF SIDE GARNISH ASSEMBLY LH 
    1. Detach the clip and remove the inner roof side garnish assembly LH.
      GTY879642Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Clip A *b Clip B
      *c Clip C - -
    2. When reusing the inner roof side garnish assembly LH:
      1. Remove the 8 clips.
        GTY862060Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        *a Clip A *b Clip B
        *c Clip C - -
  45. REMOVE INNER ROOF SIDE GARNISH ASSEMBLY RH 

    HINT: 

    Use the same procedure described for the LH side.

  46. REMOVE VISOR ASSEMBLY LH 
    1. except "TORX" Type:
      GTY1011007Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      1. Remove the 2 screws.
    2. for "TORX" Type:
      1. Using a T25 "TORX" socket wrench, remove the 2 "TORX" screws.
    3. Pull in the direction of the arrow shown in the illustration (1) to detach the visor assembly LH from the visor holder LH.
      GTY1010784Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Remove in this Direction (1)
      Remove in this Direction (2)
    4. Pull in the direction of the arrow shown in the illustration (2) and remove the visor assembly LH.
      NOTE:

      Do not twist or remove the visor assembly in any direction other than downwards as the connector may become damaged.

  47. REMOVE VISOR ASSEMBLY RH 

    HINT: 

    Use the same procedure described for the LH side.

  48. REMOVE VISOR HOLDER 

    HINT: 

    Use the same procedure for the opposite side.

    1. Turn the visor holder end approximately 45° in the direction (1) indicated by the arrow shown in the illustration, and pull it out in the direction (2) indicated by the arrow.
      GTY930867Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a 45°
      Remove in this Direction (1)
      Remove in this Direction (2)
    2. Detach the claw and remove the visor holder base.
      GTY919488Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  49. REMOVE ASSIST GRIP ASSEMBLY 

    HINT: 

    Use the same procedure for all assist grip assemblies.

    1. Insert SST into the cutout of the assist grip cover LH as shown in the illustration.
      • SST: 09813-00010 
      NOTE:

      To prevent the assist grip assembly from being damaged, make sure to insert SST straight into the cutout.

      GTY912155Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Cutout
    2. Pull SST as shown in the illustration to detach the claw.
      GTY907445Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a 30 to 45°
      Remove in this Direction
      NOTE:

      To prevent the assist grip assembly from being damaged, make sure to only pull SST as shown in the illustration.

      HINT: 

      Use the same procedure for the claw on the other side of the assist grip cover LH.

    3. Remove the assist grip cover LH.

      HINT: 

      Use the same procedure for the LH side and RH side.

    4. Pinch the clip with needle-nose pliers.

      HINT: 

      Use the same procedure for both clips.

      GTY919482Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    5. Hold the handle and pull in the direction indicated by the arrow shown in the illustration to remove the assist grip assembly.
      GTY944728Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Remove in this Direction
    6. Using needle-nose pliers, remove the clip.
  50. REMOVE REAR ASSIST GRIP ASSEMBLY LH 

    HINT: 

    Use the same procedure as for the assist grip assembly.

  51. REMOVE REAR ASSIST GRIP ASSEMBLY RH 

    HINT: 

    Use the same procedure as for the assist grip assembly.

  52. REMOVE MAP LIGHT ASSEMBLY 

    Refer to PROCEDURE - Step 1

  53. REMOVE SPOT LIGHT ASSEMBLY 

    Refer to PROCEDURE - Step 1

  54. REMOVE SENSOR COVER (w/o Rain Sensor) 

    Refer to PROCEDURE - Step 1

  55. REMOVE RAIN SENSOR COVER (w/ Rain Sensor) 

    Refer to PROCEDURE - Step 1

  56. REMOVE NO. 2 FORWARD RECOGNITION COVER 

    Refer to PROCEDURE - Step 1

  57. REMOVE NO. 1 FORWARD RECOGNITION COVER 

    Refer to PROCEDURE - Step 2

  58. REMOVE SUN ROOF OPENING TRIM MOULDING (for Moon Roof) 
    1. Remove the sun roof opening trim moulding.
      GTY944123Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  59. REMOVE ROOF HEADLINING ASSEMBLY (for Normal Roof) 
    1. for Front Pillar LH Side:
      1. Remove the protective cover installed to the front pillar LH.
      2. Disconnect the 2 connectors.
        GTY919503Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      3. Using a clip remover, detach the wire harness clamp.
      4. Install the protective cover to the front pillar LH.
    2. for Front Pillar RH Side:
      1. Remove the protective cover installed to the front pillar RH.
      2. Disconnect the connector.
        GTY919504Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      3. Using a clip remover, detach the wire harness clamp.
      4. Install the protective cover to the front pillar RH.
    3. for Rear Pillar LH Side:
      1. Disconnect the connector.
        GTY919517Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    4. for Rear Pillar RH Side:
      1. Disconnect the connector.
        GTY1007832Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    5. w/o Digital Inner Mirror:
      1. GTY913279Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

        Disconnect 3 connectors.

    6. w/ Digital Inner Mirror:
      1. GTY913275Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

        Disconnect 5 connectors.

    7. Remove the 5 clips.
      GTY919514Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    8. Turn the roof headlining diagonally and bend slightly to remove it from the back door.
      GTY1008663Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Remove in this Direction
      NOTE:
      • Make sure that wrinkles do not form in the roof headlining assembly during removal.
      • Make sure that the roof headlining assembly does not get caught on anything as it may become bent or damaged.
      • Do not damage the roof headlining assembly or vehicle interior.
      • 2 or more people are required when carrying the roof headlining assembly out of the vehicle, as it may become deformed.
  60. REMOVE ROOF HEADLINING ASSEMBLY (for Moon Roof) 
    1. for Front Pillar LH Side:
      1. Remove the protective cover installed to the front pillar LH.
      2. Disconnect the 2 connectors.
        GTY919503Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      3. Using a clip remover, detach the wire harness clamp.
      4. Install the protective cover to the front pillar LH.
    2. for Front Pillar RH Side:
      1. Remove the protective cover installed to the front pillar RH.
      2. Disconnect the connector.
        GTY919504Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      3. Using a clip remover, detach the wire harness clamp.
      4. Install the protective cover to the front pillar RH.
    3. for Rear Pillar LH Side:
      1. Disconnect the connector.
        GTY919517Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    4. for Rear Pillar RH Side:
      1. Disconnect the connector.
        GTY1007832Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    5. w/o EC Mirror:
      1. GTY913279Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

        Disconnect 3 connectors.

    6. w/ EC Mirror:
      1. GTY942743Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

        Disconnect 4 connectors.

    7. w/ Digital Inner Mirror:
      1. GTY913275Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

        Disconnect 5 connectors.

    8. Disconnect the connector.
      GTY919487Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    9. Remove the 3 clips.
      GTY919515Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    10. Turn the roof headlining assembly diagonally and bend slightly to remove it from the back door.
      GTY1008432Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Remove in this Direction
      NOTE:
      • Make sure that wrinkles do not form in the roof headlining assembly during removal.
      • Make sure that the roof headlining assembly does not get caught on anything as it may become bent or damaged.
      • Do not damage the roof headlining assembly or vehicle interior.
      • 2 or more people are required when carrying the roof headlining assembly out of the vehicle, as it may become deformed.
  61. REMOVE ROOF HEADLINING ASSEMBLY (for Panoramic Moon Roof) 
    1. for Front Pillar LH Side:
      1. Remove the protective cover installed to the front pillar LH.
      2. Disconnect the 2 connectors.
        GTY919503Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      3. Using a clip remover, detach the wire harness clamp.
      4. Install the protective cover to the front pillar LH.
    2. for Front Pillar RH Side:
      1. Remove the protective cover installed to the front pillar RH.
      2. Disconnect the connector.
        GTY919504Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      3. Using a clip remover, detach the wire harness clamp.
      4. Install the protective cover to the front pillar RH.
    3. for Rear Pillar LH Side:
      1. Disconnect the connector.
        GTY919517Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    4. for Rear Pillar RH Side:
      1. Disconnect the connector.
        GTY1007832Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    5. Disconnect 5 connectors.
      GTY913275Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    6. Disconnect the 2 connectors.
      GTY944116Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    7. Remove the 3 clips.
      GTY919515Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    8. Detach the fastener and guide.
      GTY854388Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Fastener *b Guide
    9. Turn the roof headlining assembly diagonally and bend slightly to remove it from the back door.
      GTY1007426Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Remove in this Direction
      NOTE:
      • Make sure that wrinkles do not form in the roof headlining assembly during removal.
      • Make sure that the roof headlining assembly does not get caught on anything as it may become bent or damaged.
      • Do not damage the roof headlining assembly or vehicle interior.
      • 2 or more people are required when carrying the roof headlining assembly out of the vehicle, as it may become deformed.
  62. REMOVE REAR NO. 2 SIDE RAIL SPACER LH 

    HINT: 

    Perform this procedure only when replacing the rear No. 2 side rail spacer LH.

    1. Detach the claw and remove the rear No. 2 side rail spacer LH.
      GTY919516Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  63. REMOVE REAR NO. 2 SIDE RAIL SPACER RH 

    HINT: 

    • Perform this procedure only when replacing the rear No. 2 side rail spacer RH.
    • Use the same procedure described for the LH side.
scientia non olet · About LEMON Manuals