LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2025 >> RAV4 Plug-In Hybrid SE >> Repair and Diagnosis >> Restraints >> Air Bag, SRS >> Airbag System (PHEV) - Diagnostic Codes (7 Of 7) & Symptom Tests >> Airbag System >> DTC B00D2-14: Restraint System Malfunction Indicator 1 Circuit Short to Ground or Open [06/2020 - 10/2022] >> Procedure

DTC B00D2-14: Restraint System Malfunction Indicator 1 Circuit Short to Ground or Open [06/2020 - 10/2022]: Procedure

  1. CHECK PASSENGER AIRBAG ON/OFF INDICATOR CONDITION 
    1. Turn the ignition switch to ON.
    2. Check the passenger airbag ON/OFF indicator operation.

      HINT: 

      Refer to the normal condition of the passenger airbag ON/OFF indicator.

      Refer to OPERATION CHECK [06/2020 - ]

      Result

      Result Proceed to
      Passenger airbag ON/OFF indicator "ON" is always on. A
      Passenger airbag ON/OFF indicator "ON" is always off. B

    Result: 

    B 

    See step  6

    Result: 

    A 

    See step  2

  2. CHECK CONNECTION OF CONNECTORS 
    1. Turn the ignition switch off.
    2. Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.
    3. Check that the connectors are properly connected to the airbag ECU assembly and telltale light assembly (passenger airbag ON/OFF indicator).

      Result

      Proceed to
      The connectors are properly connected
      The connectors are not properly connected

    Result: 

    The connectors are not properly connected 

    CONNECT CONNECTORS PROPERLY 

    Result: 

    The connectors are properly connected 

    See step  3

  3. CHECK CONNECTORS 
    1. Disconnect the airbag ECU assembly connector.
      GTY1018542Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 Telltale Light Assembly (Passenger Airbag ON/OFF Indicator)
      *2 Airbag ECU Assembly
      *3 Wire Harness
    2. Disconnect the telltale light assembly (passenger airbag ON/OFF indicator) connector.
    3. Check that the connectors (on the airbag ECU assembly side and telltale light assembly (passenger airbag ON/OFF indicator) side) are not damaged.

      Result

      Proceed to
      The connectors are not deformed or damaged
      The connectors are deformed or damaged

    Result: 

    The connectors are deformed or damaged 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    The connectors are not deformed or damaged 

    See step  4

  4. CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT TO GROUND) 
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      G70-35 (PAON) or G31-4 (PAON) - Body ground Always 1 MΩ or higher
      GTY973739Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 Telltale Light Assembly (Passenger Airbag ON/OFF Indicator)
      *2 Airbag ECU Assembly
      *3 Wire Harness
      *a Front view of wire harness connector
      (to Telltale Light Assembly (Passenger Airbag ON/OFF Indicator))
      *b Front view of wire harness connector
      (to Airbag ECU Assembly)

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  5

  5. CHECK PASSENGER AIRBAG ON/OFF INDICATOR 
    1. Connect the A6 telltale light assembly (passenger airbag ON/OFF indicator) connector.
      GTY973864Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 Telltale Light Assembly (Passenger Airbag ON/OFF Indicator)
      *2 Airbag ECU Assembly
      *3 Wire Harness
    2. Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.
    3. Turn the ignition switch to ON.
    4. Check the passenger airbag ON/OFF indicator operation.

      OK

      The passenger airbag ON/OFF indicator "ON" does not come on.

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE AIRBAG ECU ASSEMBLY. Refer to  REMOVAL [06/2020 - 12/2021]  , or refer to  REMOVAL [12/2021 - 10/2022] 

    Result: 

    NG 

    REPLACE TELLTALE LIGHT ASSEMBLY. Refer to  REMOVAL [06/2020 - ] 

  6. CHECK CONNECTION OF CONNECTORS 
    1. Turn the ignition switch off.
    2. Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.
    3. Check that the connectors are properly connected to the airbag ECU assembly and telltale light assembly (passenger airbag ON/OFF indicator).

      Result

      Proceed to
      The connectors are properly connected
      The connectors are not properly connected

    Result: 

    The connectors are not properly connected 

    CONNECT CONNECTORS PROPERLY 

    Result: 

    The connectors are properly connected 

    See step  7

  7. CHECK CONNECTORS 
    1. Disconnect the airbag ECU assembly connector.
      GTY1018542Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 Telltale Light Assembly (Passenger Airbag ON/OFF Indicator)
      *2 Airbag ECU Assembly
      *3 Wire Harness
    2. Disconnect the telltale light assembly (passenger airbag ON/OFF indicator) connector.
    3. Check that the connectors (on the airbag ECU assembly side and telltale light assembly (passenger airbag ON/OFF indicator) side) are not damaged.

      Result

      Proceed to
      The connectors are not deformed or damaged
      The connectors are deformed or damaged

    Result: 

    The connectors are deformed or damaged 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    The connectors are not deformed or damaged 

    See step  8

  8. CHECK HARNESS AND CONNECTOR (CHECK FOR OPEN) 
    1. Measure the resistance according to the value(s) in the table below.
      GTY973739Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 Telltale Light Assembly (Passenger Airbag ON/OFF Indicator)
      *2 Airbag ECU Assembly
      *3 Wire Harness
      *a Front view of wire harness connector
      (to Telltale Light Assembly (Passenger Airbag ON/OFF Indicator))
      *b Front view of wire harness connector
      (to Airbag ECU Assembly)

      Standard Resistance

      Tester Connection Condition Specified Condition
      G70-35 (PAON) - G31-4 (PAON) Always Below 1 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  9

  9. CHECK HARNESS AND CONNECTOR (POWER SOURCE VOLTAGE) 
    1. Turn the ignition switch off.
      GTY973471Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Front view of wire harness connector
      (to Telltale Light Assembly (Passenger Airbag ON/OFF Indicator))
    2. Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.
    3. Disconnect the telltale light assembly (passenger airbag ON/OFF indicator) connector.
    4. Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.
    5. Turn the ignition switch to ON.
    6. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection Switch Condition Specified Condition
      G31-9 (IG) - Body ground Ignition switch ON 11 to 14 V

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE AIRBAG ECU ASSEMBLY. Refer to  REMOVAL [06/2020 - 12/2021]  , or refer to  REMOVAL [12/2021 - 10/2022] 

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

scientia non olet · About LEMON Manuals