LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2025 >> RAV4 Plug-In Hybrid SE >> Repair and Diagnosis >> Maintenance >> Procedures >> Maintenance - Service Information (PHEV) >> Front Disc Brake Pad >> Installation [12/2021 - 10/2022] >> Procedure

Installation [12/2021 - 10/2022]: Procedure

  1. INSTALL FRONT DISC BRAKE ANTI-SQUEAL SHIM KIT 
    NOTE:
    • When replacing worn front disc brake pads, the front disc brake anti-squeal shims and front disc brake pad wear indicator plates must be replaced together with the front disc brake pads.
    • Do not apply disc brake grease to the lining surface of the brake pad.
    • Install the front disc brake pad wear indicator plates in the correct position and direction.
    • Install the front disc brake anti-squeal shims in the correct position and direction.
    1. Install the front No. 1 disc brake anti-squeal shim and front disc brake anti-squeal shim to each front disc brake pad.
      GTY1115019Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 Front No. 1 Disc Brake Anti-squeal Shim
      *2 Front Disc Brake Anti-squeal Shim
      *3 Front Disc Brake Pad Wear Indicator Plate
    2. Install a new front disc brake pad wear indicator plate to each front disc brake pad.
  2. INSTALL FRONT DISC BRAKE PAD 
    WARNING:
    • Be careful not to get pinched by the front disc brake cylinder assembly or other parts when installing the front disc brake pads.
    • After lifting up the front disc brake cylinder assembly, secure it in place before performing any work on it.
    • The front disc brake cylinder assembly could fall, pinching hands or fingers and causing injury.
    GTY1112737Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Push in the front disc brake piston.
      NOTE:
      • Make sure the brake fluid does not overflow from the reservoir.
      • Do not forcibly push in the front disc brake piston.
    2. Install the 2 front disc brake pads to the front disc brake cylinder mounting.
      NOTE:
      • Keep the friction surfaces of the front disc brake pads and front disc free from oil and grease.
      • Install the front disc brake pad so that the pad wear indicator plate is mounted on the upper side of the vehicle.
    3. Install the 2 anti-squeal springs to the front disc brake pads.
      NOTE:
      • When replacing the front disc brake pads with new ones, make sure to replace the anti-squeal springs at the same time.
      • Be sure to install the anti-squeal springs into the front disc brake pad installation holes as far as they will go.
    4. Hold the front disc brake cylinder slide pin (lower side) and install the front disc brake cylinder assembly to the front disc brake cylinder mounting with the bolt.

      Torque: 34.3 N.m (350 kgf/cm, 25 ft.lbf) 

      NOTE:
      • Install the front disc brake cylinder assembly while holding both of the front disc brake pads because the anti-squeal springs may fall off the front disc brake pads.
      • Be sure that the anti-squeal springs are installed to the front disc brake pads.
    5. Depress the brake pedal several times.
  3. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL 

    Refer to INSTALLATION [06/2020 - 10/2022]

  4. INSPECT BRAKE FLUID LEVEL IN RESERVOIR 

    Refer to ON-VEHICLE INSPECTION [06/2020 - ]

  5. INSTALL FRONT WHEEL 

    Refer to INSTALLATION [06/2020 - ] 

  6. INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL 

    Refer to WORK PROCEDURE [06/2020 - 10/2022]

    HINT: 

    When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

    Refer to AUTOMATIC LEARNING CHART [12/2021 - ]

scientia non olet · About LEMON Manuals