LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2025 >> Prius Plug-In Hybrid SE >> Repair and Diagnosis >> Suspension >> Rear Suspension >> Suspension System (Rear) - Service Information (2 Of 2) >> Rear Stabilizer Bar >> Installation [03/2023 - ] >> Procedure

Installation [03/2023 - ]: Procedure

  1. INSTALL REAR STABILIZER LINK ASSEMBLY LH 
    1. GTY1155015Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      1. Install the rear stabilizer link assembly LH to the rear trailing arm assembly with the nut.

        Torque: 79 N*m (806 kgf*cm, 58 ft.*lbf) 

        HINT: 

        If the ball joint turns together with the nut, use a 6 mm hexagon socket wrench to hold the stud bolt.

  2. INSTALL REAR STABILIZER LINK ASSEMBLY RH 
  3. INSTALL REAR STABILIZER BAR (for HEV Model 2WD) 
    1. GTY1149042Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Identification Mark - -
      1. Temporarily Install the rear stabilizer bar to the rear stabilizer link assembly LH with the bolt and nut.
        NOTE:

        Tighten the nut with the bolt secured.

      2. Temporarily Install the rear stabilizer bar to the rear stabilizer link assembly RH with the bolt and nut.
        NOTE:

        Tighten the nut with the bolt secured.

      3. Install the rear stabilizer bar to the rear suspension member sub-assembly with the 4 bolts.

        Torque: 78 N*m (795 kgf*cm, 58 ft.*lbf) 

        NOTE:
        • Ensure that the identification mark faces the right side of the vehicle.
        • Temporarily tighten the 3 bolts in the order of (A), (B) and (D), and then fully tighten the 4 bolts in the order of (C), (D), (A), and (B).
  4. INSTALL REAR STABILIZER BAR (for HEV Model AWD, PHEV Model) 
    1. GTY1153036Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Identification Mark - -
      1. Temporarily Install the rear stabilizer bar to the rear stabilizer link assembly LH with the bolt and nut.
        NOTE:

        Tighten the nut with the bolt secured.

      2. Temporarily Install the rear stabilizer bar to the rear stabilizer link assembly RH with the bolt and nut.
        NOTE:

        Tighten the nut with the bolt secured.

      3. Install the rear stabilizer bar to the rear suspension member sub-assembly with the 4 bolts.

        Torque: 78 N*m (795 kgf*cm, 58 ft.*lbf) 

        NOTE:
        • Ensure that the identification mark faces the right side of the vehicle.
        • Temporarily tighten the 3 bolts in the order of (C), (D) and (B), and then fully tighten the 4 bolts in the order of (A), (B), (C), and (D).
  5. STABILIZE SUSPENSION 
    Refer to PROCEDURE - Step 4
  6. INSTALL REAR STABILIZER LINK ASSEMBLY LH 
    1. GTY1156200Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      1. Fully tighten the rear stabilizer link assembly LH with the nut.

        Torque: 79 N*m (806 kgf*cm, 58 ft.*lbf) 

        NOTE:

        Tighten the nut with the bolt secured.

  7. INSTALL REAR STABILIZER LINK ASSEMBLY RH 
  8. INSTALL REAR WHEEL 

    Refer to INSTALLATION [12/2022 - ]

  9. INSTALL REAR FLOOR SIDE MEMBER COVER LH (for HEV Model) 

    See step  7

  10. INSTALL REAR FLOOR SIDE MEMBER COVER RH (for HEV Model) 

    See step  8

  11. INSTALL BATTERY BOX COVER (for PHEV Model) 

    Refer to PROCEDURE - Step 8

scientia non olet · About LEMON Manuals