LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2025 >> Prius Plug-In Hybrid SE >> Repair and Diagnosis >> Body & Frame >> Exterior Body Panels >> Exterior Panels / Trim - Service Information (1 Of 2) >> Name Plate >> Removal [12/2022 - 03/2023] >> Procedure

Removal [12/2022 - 03/2023]: Procedure

  1. REMOVE RADIATOR GRILLE (OR FRONT PANEL) EMBLEM 
    1. GTY1141704Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Heated Part - -
      1. Apply protective tape around the radiator grille (or front panel) emblem as shown in the illustration.
      2. Using a heat light, heat the front bumper cover and radiator grille (or front panel) emblem.
        WARNING:
        • Do not touch the heat light and heated parts, touching the heat light may result in burns.
        • Touching heated parts for a long time may result in burns.
        GTY583249Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        *a Heated Part
        *b Heat Light
        NOTE:

        Do not heat the front bumper cover and radiator grille (or front panel) emblem excessively.

        Standard

        Item Temperature
        Front Bumper Cover 20 to 30 °C (68 to 86 °F)
      3. Using a moulding remover, separate the double-sided tape and disengage the 2 pins to remove the radiator grille (or front panel) emblem.
        NOTE:

        Be careful not to damage the front bumper cover.

  2. REMOVE NO. 1 BACK DOOR EMBLEM 
    1. GTY1146904Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Heated Part - -
      1. Apply protective tape around the No. 1 back door emblem as shown in the illustration.
      2. Using a heat light, heat the rear light assembly and No. 1 back door emblem.
        WARNING:
        • Do not touch the heat light and heated parts, touching the heat light may result in burns.
        • Touching heated parts for a long time may result in burns.
        GTY583249Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        *a Heated Part
        *b Heat Light
        NOTE:

        Do not heat the rear light assembly or No. 1 back door emblem excessively.

        Standard

        Item Temperature
        Rear Light Assembly 20 to 30 °C (68 to 86 °F)
      3. Tie objects that can serve as handles (for example, wooden blocks) to both wire ends.
      4. Insert a piano wire between the rear light assembly and No. 1 back door emblem.
      5. Pull the piano wire and cut the double-sided tape that holds the No. 1 back door emblem to the rear light assembly.
        NOTE:

        Be careful not to damage the rear light assembly.

  3. REMOVE NO. 4 BACK DOOR NAME PLATE (w/ No. 4 Back Door Name Plate) 
    1. GTY1135001Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Wooden Blocks *b Piano Wire
      Heated Part Protective Tape
      1. Apply protective tape around the No. 4 back door name plate as shown in the illustration.
      2. Using a heat light, heat the rear light assembly and No. 4 back door name plate.
        WARNING:
        • Do not touch the heat light and heated parts, touching the heat light may result in burns.
        • Touching heated parts for a long time may result in burns.
        GTY583249Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        *a Heated Part
        *b Heat Light
        NOTE:

        Do not heat the rear light assembly or No. 4 back door name plate excessively.

        Standard

        Item Temperature
        Rear Light Assembly 20 to 30 °C (68 to 86 °F)
      3. Tie objects that can serve as handles (for example, wooden blocks) to both wire ends.
      4. Insert a piano wire between the rear light assembly and No. 4 back door name plate.
      5. Pull the piano wire and cut the double-sided tape that holds the No. 4 back door name plate to the rear light assembly.
        NOTE:

        Be careful not to damage the rear light assembly.

  4. REMOVE NO. 1 BACK DOOR NAME PLATE 
    1. GTY1141566Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Wooden Blocks *b Piano Wire
      Heated Part Protective Tape
      1. Apply protective tape around the No. 1 back door name plate as shown in the illustration.
      2. Using a heat light, heat the back door panel and No. 1 back door name plate.
        WARNING:
        • Do not touch the heat light and heated parts, touching the heat light may result in burns.
        • Touching heated parts for a long time may result in burns.
        GTY583249Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        *a Heated Part
        *b Heat Light
        NOTE:

        Do not heat the back door panel or No. 1 back door name plate excessively.

        Standard

        Item Temperature
        Back Door Panel 40 to 60°C (104 to 140°F)
      3. Tie objects that can serve as handles (for example, wooden blocks) to both wire ends.
      4. Insert a piano wire between the back door panel and No. 1 back door name plate.
      5. Pull the piano wire and cut the double-sided tape that holds the No. 1 back door name plate to the back door panel.
        NOTE:

        Be careful not to damage the back door panel.

  5. REMOVE NO. 3 BACK DOOR EMBLEM 
    1. GTY1135001Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Wooden Blocks *b Piano Wire
      Heated Part Protective Tape
      1. Apply protective tape around the No. 3 back door emblem as shown in the illustration.
      2. Using a heat light, heat the back door panel and No. 3 back door emblem.
        WARNING:
        • Do not touch the heat light and heated parts, touching the heat light may result in burns.
        • Touching heated parts for a long time may result in burns.
        GTY583249Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        *a Heated Part
        *b Heat Light
        NOTE:

        Do not heat the back door panel or emblem excessively.

        Standard

        Item Temperature
        Back Door Panel 40 to 60°C (104 to 140°F)
      3. Tie objects that can serve as handles (for example, wooden blocks) to both wire ends.
      4. Insert a piano wire between the back door panel and No. 3 back door emblem.
      5. Pull the piano wire and cut the double-sided tape that holds the No. 3 back door emblem to the back door panel.
        NOTE:

        Be careful not to damage the back door panel.

  6. REMOVE SIDE PANEL EMBLEM (w/ Side Panel Emblem) 

    HINT: 

    Use the same procedure for the RH side and LH side.

    1. GTY1134433Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Wooden Blocks *b Piano Wire
      Heated Part Protective Tape
      1. Apply protective tape around the side panel emblem as shown in the illustration.
      2. Using a heat light, heat the front door panel and side panel emblem.
        WARNING:
        • Do not touch the heat light and heated parts, touching the heat light may result in burns.
        • Touching heated parts for a long time may result in burns.
        GTY583249Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        *a Heated Part
        *b Heat Light
        NOTE:

        Do not heat the front door panel or side panel emblem excessively.

        Standard

        Item Temperature
        Front Door Panel 40 to 60°C (104 to 140°F)
      3. Tie objects that can serve as handles (for example, wooden blocks) to both wire ends.
      4. Insert a piano wire between the front door panel and front side panel emblem.
      5. Pull the piano wire and cut the double-sided tape that holds the side panel emblem to the front door panel.
        NOTE:

        Be careful not to damage the front door panel.

scientia non olet · About LEMON Manuals