LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2025 >> Corolla LE >> Repair and Diagnosis >> External Pages >> Different car >> Section 91 (Meter / Gauge System (Except HEV) - Diagnostic Codes (2 Of 2), Symptom Tests & Circuit Tests) >> METER / GAUGE SYSTEM (for Gasoline Model) >> Steering Pad Switch Circuit [06/2018 - 09/2022] >> Procedure

Steering Pad Switch Circuit [06/2018 - 09/2022]: Procedure

WARNING: This page is about a different car, the 2022 Toyota Corolla, 2021 Toyota Corolla, 2020 Toyota Corolla, and 2019 Toyota Corolla. However, it is still accessible from the selected car via links, so may be relevant.
  1. INSPECT STEERING PAD SWITCH ASSEMBLY 
    1. Remove the steering pad switch assembly.

      Refer to REMOVAL [06/2018 - 01/2019] , or refer to REMOVAL [01/2019 - 03/2019] , or refer to REMOVAL [03/2019 - 09/2022]

    2. Inspect the steering pad switch assembly.

      Refer to INSPECTION [06/2018 - 01/2019] , or refer to INSPECTION [01/2019 - 03/2019] , or refer to INSPECTION [03/2019 - 09/2022]

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPLACE STEERING PAD SWITCH ASSEMBLY. Refer to  REMOVAL [06/2018 - 01/2019]  , or refer to  REMOVAL [01/2019 - 03/2019]  , or refer to  REMOVAL [03/2019 - 09/2022] 

    Result: 

    OK 

    See step  2

  2. INSPECT SPIRAL CABLE SUB-ASSEMBLY 
    1. Remove the spiral cable sub-assembly.

      Refer to REMOVAL [06/2018 - 01/2019] , or refer to REMOVAL [01/2019 - 03/2019] , or refer to REMOVAL [03/2019 - 09/2022]

    2. Inspect the spiral cable sub-assembly.

      Refer to INSPECTION [06/2018 - ]

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPLACE SPIRAL CABLE SUB-ASSEMBLY. Refer to  REMOVAL [06/2018 - 01/2019]  , or refer to  REMOVAL [01/2019 - 03/2019]  , or refer to  REMOVAL [03/2019 - 09/2022] 

    Result: 

    OK 

    See step  3

  3. CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - COMBINATION METER ASSEMBLY) 
    1. Disconnect the I4 combination meter assembly connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      I82-11 (+DP) - I4-32 (MSM+) Always Below 1 Ω
      I82-10 (+DP2) - I4-15 (MSTI) Always Below 1 Ω
      I82-11 (+DP) or I4-32 (MSM+) - Body ground Always 10 kΩ or higher
      I82-10 (+DP2) or I4-15 (MSTI) - Body ground Always 10 kΩ or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  4

  4. CHECK COMBINATION METER ASSEMBLY (OUTPUT VOLTAGE) 
    GTY888904Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    *a Front view of wire harness connector
    (to Spiral Cable Sub-assembly)
    1. Connect the I4 combination meter assembly connector.
    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection Condition Specified Condition
      I82-11 (+DP) - Body ground Engine switch on (IG) 4.8 to 5.2 V
      I82-10 (+DP2) - Body ground Engine switch on (IG) 4.8 to 5.2 V

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPLACE COMBINATION METER ASSEMBLY. Refer to  REMOVAL [06/2018 - 01/2019]  , or refer to  REMOVAL [01/2019 - 03/2019]  , or refer to  REMOVAL [03/2019 - 09/2022] 

    Result: 

    OK 

    See step  5

  5. CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - RADIO AND DISPLAY RECEIVER ASSEMBLY) 
    1. Disconnect the I55 radio and display receiver assembly connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      I82-4 (EAU) - I55-24 (SWG) Always Below 1 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  6

  6. CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - BODY GROUND) 
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      I55-1 (GND1) - Body ground Always Below 1 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY. Refer to  REMOVAL [06/2018 - 01/2019]  , or refer to  REMOVAL [01/2019 - 03/2019]  , or refer to  REMOVAL [03/2019 - 09/2022] 

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

scientia non olet · About LEMON Manuals