Caution / Notice / Hint

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during battery charger connector opening lid sub-assembly removal/installation are shown below.

WARNING:

Orange wire harnesses and connectors indicate high-voltage circuits. To prevent electric shock, always follow the procedure described in the repair information.

Refer to PRECAUTION [12/2022 - ] (HEV) or PRECAUTION [03/2023 - ] (PHEV)

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

To prevent electric shock, wear insulated gloves when working on wire harnesses and components of the high voltage system.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

NOTE:

After the ignition switch is turned off, the radio and display receiver assembly recordsvarious types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 3 minutes before disconnecting the cable from the negative(-) auxiliary battery terminal.
When the cable is disconnected from the negative (-) auxiliary battery terminal and the security lock setting has been enabled, multi-display operations will be disabled uponnext startup unless the password is entered. Be sure to check the security lock setting before disconnecting the cable from the negative (-) auxiliary battery terminal.

HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed	Necessary Procedures	Link
Front Camera System	Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more.	Refer to INITIALIZATION [12/2022 - ]

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed	Necessary Procedures	Link
Power Door Lock Control System*1 Back door opener	Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch.	Refer to INITIALIZATION [12/2022 - ]
Power Back Door System*2	Reset back door close position	Refer to INITIALIZATION [12/2022 - ]
Air Conditioning System	After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized.	-

*1: w/o Power Back Door System*2: w/ Power Back Door System

Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.

COMPONENTS (REMOVAL)

Fig 1: Charge Lid Opener Unit Removal Components (1 Of 5)

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

Callout - Procedure		Part Name Code
1	SERVICE PLUG GRIP	G3834	-	-	-

Fig 2: Charge Lid Opener Unit Removal Components (2 Of 5)

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

Callout - Procedure		Part Name Code
2	TONNEAU COVER ASSEMBLY	64910J	-	-	-
3	DECK BOARD ASSEMBLY	58410B	-	-	-
4	BATTERY SERVICE HOLE COVER ASSEMBLY	58440	-	-	-
5	REAR SEAT HEADREST ASSEMBLY	71940A	-	-	-
6	REAR SEAT CENTER HEADREST ASSEMBLY	71960B	-	-	-
7	REAR CENTER SEAT OUTER BELT ASSEMBLY	73350C	See step 7	-	-
8	REAR SEATBACK ASSEMBLY RH	-	See step 8	-	-
9	REAR SEAT CUSHION ASSEMBLY	-	See step 9	-	-
10	REAR SEAT CUSHION LOCK HOOK	72693	-	-	-

*A	for RH Side	*B	w/ Center Headrest
•	Non-reusable part	-	-

Fig 3: Charge Lid Opener Unit Removal Components (3 Of 5)

Callout - Procedure		Part Name Code
11	DECK FLOOR BOX RH	64995	-	-	-
12	DECK FLOOR BOX LH	64997	-	-	-
13	LUGGAGE HOLD BELT STRIKER ASSEMBLY	58460D	-	-	-
14	REAR DECK TRIM COVER	64716D	-	-	-

for Rear Side

Fig 4: Charge Lid Opener Unit Removal Components (4 Of 5)

Callout - Procedure		Part Name Code
15	REAR DOOR SCUFF PLATE INSIDE RH	67917F	-	-	-
16	REAR DOOR OPENING TRIM WEATHERSTRIP RH	62331A	-	-	-
17	REAR SEAT BACK HINGE SUB-ASSEMBLY RH	71303C	-	-	-
18	REAR SEAT SIDE GARNISH RH	62551F	See step 18	-	-
19	LUGGAGE HOLD BELT STRIKER ASSEMBLY	58460D	-	-	-
20	NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY	81330	See step 20	-	-
21	DECK TRIM SIDE PANEL ASSEMBLY RH	64730B	See step 21	-	-

for RH Side

Fig 5: Charge Lid Opener Unit Removal Components (5 Of 5)

Callout - Procedure		Part Name Code
22	AC CHARGER INLET CABLE	G9081C	See step 22	-	-
23	FUEL TANK CAP PLATE	-	See step 23	-	-
24	BATTERY SERVICE OPENING LID SUB-ASSEMBLY	58209F	See step 24	-	-
25	BATTERY CHARGER CONNECTOR OPENING LID SUB-ASSEMBLY	58409E	See step 25	-	-