DTC B1500-13: Fuel Sender Circuit Open [02/2024 - ]: Procedure

Refer to INSPECTION [02/2024 - ]

Result

Result: 

NG 

REPLACE FUEL SENDER GAUGE ASSEMBLY 

Refer to REMOVAL [02/2024 - ]

Result: 

OK 

See step  2

Pre-procedure1

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Remove the fuel suction plate sub-assembly.

   HINT: 

   Refer to DISASSEMBLY [02/2024 - ]

   Procedure1

2. Measure the resistance according to the value(s) in the table below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   N3-1 (FV) - B-1	Always	Below 1 Ω
   N3-2 (FE) - B-2	Always	Below 1 Ω
   N3-3 (FR) - B-3	Always	Below 1 Ω

   Result

   Proceed to
   OK
   NG

   Post-procedure1

3. None

Result: 

NG 

REPLACE FUEL SUCTION PLATE SUB-ASSEMBLY 

Refer to DISASSEMBLY [02/2024 - ]

Result: 

OK 

See step  3

Pre-procedure1

1. Disconnect the N3 fuel suction plate sub-assembly connector.
2. Disconnect the E7*1 or E5*2 combination meter assembly connector.
   1. *1: for 7 Inch Multi-information Display Type
   2. *2: for 12.3 Inch Multi-information Display Type

   Procedure1

3. Measure the resistance according to the value(s) in the table below.

   Standard Resistance

   FOR 7 INCH MULTI-INFORMATION DISPLAY TYPE
   
   

   Tester Connection	Condition	Specified Condition
   N3-3 (FR) - E7-34 (FR)	Always	Below 1 Ω
   N3-2 (FE) - E7-17 (FE&B)	Always	Below 1 Ω
   N3-1 (FV) - E7-18 (FV)	Always	Below 1 Ω
   N3-3 (FR) or E7-34 (FR) - Other terminals and body ground	Always	10 kΩ or higher
   N3-2 (FE) or E7-17 (FE&B) - Other terminals and body ground	Always	10 kΩ or higher
   N3-1 (FV) or E7-18 (FV) - Other terminals and body ground	Always	10 kΩ or higher

   FOR 12.3 INCH MULTI-INFORMATION DISPLAY TYPE
   
   

   Tester Connection	Condition	Specified Condition
   N3-3 (FR) - E5-7 (FR)	Always	Below 1 Ω
   N3-2 (FE) - E5-25 (FE&B)	Always	Below 1 Ω
   N3-1 (FV) - E5-23 (FV)	Always	Below 1 Ω
   N3-3 (FR) or E5-7 (FR) - Other terminals and body ground	Always	10 kΩ or higher
   N3-2 (FE) or E5-25 (FE&B) - Other terminals and body ground	Always	10 kΩ or higher
   N3-1 (FV) or E5-23 (FV) - Other terminals and body ground	Always	10 kΩ or higher

   Result

   Proceed to
   OK
   NG

   Post-procedure1

4. None

Result: 

OK 

REPLACE COMBINATION METER ASSEMBLY 

Refer to REMOVAL [02/2024 - ]

Result: 

NG 

REPAIR OR REPLACE HARNESS OR CONNECTOR