Removal [11/2021 - ]: Procedure
- DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
Refer to PROCEDURE - Step 1 - REMOVE REAR SEAT CUSHION ASSEMBLY
Refer to PROCEDURE - Step 2 - REMOVE NO. 1 CENTER CONSOLE SILENCER
Refer to PROCEDURE - Step 3
- REMOVE REAR SEATBACK ASSEMBLY
Refer to PROCEDURE - Step 4 - REMOVE FRONT DOOR SCUFF PLATE RH
- REMOVE FRONT DOOR SCUFF PLATE LH
- Use the same procedure as for the RH side.
- REMOVE COWL SIDE TRIM BOARD RH
- REMOVE COWL SIDE TRIM BOARD LH
- Use the same procedure as for the RH side.
- REMOVE FRONT DOOR SCUFF PLATE OUTSIDE RH
- REMOVE FRONT DOOR SCUFF PLATE OUTSIDE LH
- Use the same procedure as for the RH side.
- REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH
Refer to PROCEDURE - Step 3
- REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH
- Use the same procedure as for the LH side.
- REMOVE FRONT PILLAR GARNISH RH
- Pull the front pillar garnish RH towards the center of the vehicle.
- Release the hook at the end of the front pillar garnish clip, and remove the front pillar garnish RH.NOTE:
- Do not use any tool when releasing the hook at the end of the front pillar garnish RH.
- Be careful not to damage the front pillar garnish RH surface and curtain airbag module.
- Release the hook at the end of the front pillar garnish clip, and remove the front pillar garnish RH.
- REMOVE FRONT PILLAR GARNISH LH
- Use the same procedure as for the RH side.
- REMOVE LUGGAGE COMPARTMENT FLOOR MAT
- Remove the luggage compartment floor mat.
- REMOVE REAR FLOOR FINISH PLATE
- REMOVE LUGGAGE COMPARTMENT TRIM COVER INNER RH
- REMOVE LUGGAGE COMPARTMENT TRIM COVER INNER LH
- Use the same procedure as for the RH side.
- REMOVE LUGGAGE COMPARTMENT TRIM COVER RH
- REMOVE LUGGAGE COMPARTMENT TRIM COVER LH
- Use the same procedure as for the RH side.
- REMOVE QUARTER TRIM LID SUB-ASSEMBLY RH
- REMOVE QUARTER TRIM LID SUB-ASSEMBLY LH
- Use the same procedure as for the RH side.
- REMOVE REAR WINDOW SIDE GARNISH RH
- REMOVE REAR WINDOW SIDE GARNISH LH
- Use the same procedure as for the RH side.
- REMOVE REAR QUARTER TRIM GARNISH FRONT RH
- REMOVE REAR QUARTER TRIM GARNISH FRONT LH
- Use the same procedure as for the RH side.
- DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY RH
Refer to PROCEDURE - Step 10
- DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY LH
- Use the same procedure as for the RH side.
- REMOVE CENTER PILLAR GARNISH RH
- REMOVE CENTER PILLAR GARNISH LH
- Use the same procedure as for the RH side.
- REMOVE VISOR ASSEMBLY RH
- REMOVE VISOR ASSEMBLY LH
- Use the same procedure as for the RH side.
- REMOVE VISOR HOLDER
- REMOVE NO. 1 FORWARD RECOGNITION COVER (w/o EyeSight)
Refer to PROCEDURE - Step 3
- REMOVE MAP LIGHT ASSEMBLY (w/o EyeSight)
Refer to PROCEDURE - Step 4
- REMOVE MAP LIGHT ASSEMBLY (w/ EyeSight)
Refer to PROCEDURE - Step 3 - REMOVE ROOF HEADLINING ASSEMBLY
- Remove the harness clips of the No. 2 antenna cord sub-assembly and the No. 1 roof wire, and disconnect the connectors.
- Remove the clips.
- Disconnect the connector.
*A w/o EyeSight *B w/ EyeSight - Disengage the clips.
Remove in this Direction - - - Remove the roof headlining assembly from the vehicle through the front passenger door as shown in the illustration.NOTE:
Do not damage the roof headlining assembly or body interior.
- Remove the roof headlining assembly from the vehicle through the front passenger door as shown in the illustration.