LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2024 >> Corolla LE >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 63 (Hybrid Control System (Li-Ion W/ Pa10) - Diagnostic Codes (3 Of 3) & Circuit Tests) >> HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY with PA10) >> Drive Mode Select Switch Circuit [09/2022 - ] >> Procedure

Drive Mode Select Switch Circuit [09/2022 - ]: Procedure

WARNING: This page is about a different variant/trim than selected.
  1. READ VALUE USING GTS (CAN BUS CHECK) 

    See step  2

    Result

    Result Proceed to
    All of the ECUs and sensors that are currently connected to the CAN communication system are displayed A
    None of the ECUs and sensors that are currently connected to the CAN communication system are displayed, or some of them are not displayed B

    Result: 

    B 

    GO TO CAN COMMUNICATION SYSTEM. Refer to  HOW TO PROCEED WITH TROUBLESHOOTING [09/2022 - ] 

    Result: 

    A 

    See step  2

  2. CHECK DTC OUTPUT (HEALTH CHECK) 

    See step  3

    Result

    Result Proceed to
    No DTCs are output A
    DTCs are output B

    Result: 

    B 

    GO TO DTC CHART. Refer to  DIAGNOSTIC TROUBLE CODE CHART [09/2022 - ] 

    Result: 

    A 

    See step  3

  3. CHECK DRIVE MODE STATUS 
    1. Turn the ignition switch to ON.
    2. Operate the drive mode select switch (combination switch assembly) to change the drive mode.
    3. Check that the drive mode indicator is displayed on the multi-information display and changes according to the selected drive mode.

      Result

      Result Proceed to
      The display changes according to the drive mode select switch operation A
      The display does not change according to the drive mode select switch operation
      (for Push Type Switch)      		 B
      The display does not change according to the drive mode select switch operation
      (for Toggle Type Switch)      		 C
    4. Turn the power switch off.

    Result: 

    A 

    GO TO PROBLEM SYMPTOMS TABLE. Refer to  PROBLEM SYMPTOMS TABLE [09/2022 - ] 

    Result: 

    C 

    See step  8

    Result: 

    B 

    See step  4

  4. READ VALUE USING GTS (POWERTRAIN DRIVE MODE SWITCH) 
    1. Read the value displayed on the GTS.

      Powertrain > Hybrid Control > Data List 

      Tester Display
      Powertrain Drive Mode Switch

      Result

      Result Proceed to
      The display changes according to the drive mode select switch operation A
      Other than above B
    2. Turn the ignition switch off.

    Result: 

    A 

    CHECK METER / GAUGE SYSTEM. Refer to  HOW TO PROCEED WITH TROUBLESHOOTING [09/2022 - 11/2022]  , or refer to  HOW TO PROCEED WITH TROUBLESHOOTING [11/2022 - ] 

    Result: 

    B 

    See step  5

  5. INSPECT DRIVE MODE SELECT SWITCH (COMBINATION SWITCH ASSEMBLY) 

    Refer to INSPECTION [01/2019 - ]

    Result

    Proceed to
    OK
    NG

    Result: 

    NG 

    REPLACE COMBINATION SWITCH ASSEMBLY. Refer to  REMOVAL [01/2019 - ] 

    Result: 

    OK 

    See step  6

  6. CHECK HARNESS AND CONNECTOR (DRIVE MODE SELECT SWITCH (COMBINATION SWITCH ASSEMBLY) - BODY GROUND) 
    1. Disconnect the drive mode select switch (combination switch assembly) connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      I61-5 (E) - Body ground Always Below 1 Ω
    3. Reconnect the drive mode select switch (combination switch assembly) connector.

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  7

  7. CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - DRIVE MODE SELECT SWITCH (COMBINATION SWITCH ASSEMBLY)) 
    1. Disconnect the hybrid vehicle control ECU connector.
    2. Disconnect the drive mode select switch (combination switch assembly) connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      I3-37 (PDRV) - I61-6 (DRV) Always Below 1 Ω
      I3-37 (PDRV) or I61-6 (DRV) - Body ground Always 10 kΩ or higher
    4. Reconnect the drive mode select switch (combination switch assembly) connector.
    5. Reconnect the hybrid vehicle control ECU connector.

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE HYBRID VEHICLE CONTROL ECU. Refer to  REMOVAL [09/2022 - ] 

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

  8. READ VALUE USING GTS (DRIVE MODE SWITCH) 
    1. Read the value displayed on the GTS.

      Powertrain > Hybrid Control > Data List 

      Tester Display
      Drive Mode Switch-
      Drive Mode Switch+

      Result

      Result Proceed to
      The display changes according to the drive mode select switch operation A
      Other than above B
    2. Turn the ignition switch off.

    Result: 

    A 

    CHECK METER / GAUGE SYSTEM. Refer to  HOW TO PROCEED WITH TROUBLESHOOTING [09/2022 - 11/2022]  , or refer to  HOW TO PROCEED WITH TROUBLESHOOTING [11/2022 - ] 

    Result: 

    B 

    See step  9

  9. INSPECT DRIVE MODE SELECT SWITCH (COMBINATION SWITCH ASSEMBLY) 

    Refer to INSPECTION [01/2019 - ]

    Result

    Proceed to
    OK
    NG

    Result: 

    NG 

    REPLACE COMBINATION SWITCH ASSEMBLY. Refer to  REMOVAL [01/2019 - ] 

    Result: 

    OK 

    See step  10

  10. CHECK HARNESS AND CONNECTOR (DRIVE MODE SELECT SWITCH (COMBINATION SWITCH ASSEMBLY) - BODY GROUND) 
    1. Disconnect the drive mode select switch (combination switch assembly) connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      I61-5 (E) - Body ground Always Below 1 Ω
    3. Reconnect the drive mode select switch (combination switch assembly) connector.

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  11

  11. CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - DRIVE MODE SELECT SWITCH (COMBINATION SWITCH ASSEMBLY)) 
    1. Disconnect the hybrid vehicle control ECU connector.
    2. Disconnect the drive mode select switch (combination switch assembly) connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      I3-37 (DMS-) - I61-6 (E) Always Below 1 Ω
      I3-38 (DMS+) - I61-7 (SEL) Always Below 1 Ω
      I3-37 (DMS-) or I61-6 (E) - Body ground Always 10 kΩ or higher
      I3-38 (DMS+) or I61-7 (SEL) - Body ground Always 10 kΩ or higher
    4. Reconnect the drive mode select switch (combination switch assembly) connector.
    5. Reconnect the hybrid vehicle control ECU connector.

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE HYBRID VEHICLE CONTROL ECU. Refer to  REMOVAL [09/2022 - ] 

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

scientia non olet · About LEMON Manuals