How To Proceed With Troubleshooting [01/2019 - 09/2022]: Procedure

Result

Result: 

NEXT 

See step  2

1. Interview the customer to confirm the problem.

   HINT: 

   It is important to collect as much specific information as possible from the customer to allow for a quick repair.

   Result

   Proceed to
   NEXT

Result: 

NEXT 

See step  3

1. Turn the power switch off.
2. Connect the Techstream to the DLC3.
3. Turn the power switch on (IG).
4. Turn the Techstream on.
5. Enter the following menus: Chassis / Tire Pressure Monitor / Data List.
6. Set all tire pressures to the specified value.
   NOTE:

   Refer to the link as the procedure for adjusting the tire pressures differs depending on the temperature of the tires.

   Refer to INSPECTION [01/2019 - 03/2019] , or refer to INSPECTION [03/2019 - 09/2022]

7. Display "ID Tire Inflation Pressure" in the Data List and check that the tire pressure values match the adjusted pressure amount.

   HINT: 

   It may take a few minutes until the values are displayed.

8. Perform initialization.

   Refer to INITIALIZATION [01/2019 - 09/2022] 

   HINT: 

   The tire pressure warning system illuminates the tire pressure warning light to warn the driver when the following condition is met:

   • The tire pressure drops to approximately 75% or less of the tire pressure set when system initialization was performed using the steering pad switch assembly.

   Result

   Result	Proceed to
   Tire pressure warning light remains on	A
   Tire pressure warning light goes off	B

Result: 

B 

See step  11

Result: 

A 

See step  4

1. Check the ECUs connected to the CAN bus.

   Refer to DIAGNOSIS SYSTEM [01/2019 - 04/2020] , or refer to DIAGNOSIS SYSTEM [04/2020 - 09/2022]

   Result

   Result	Proceed to
   No malfunction appears	A
   Malfunction appears	B

Result: 

B 

GO TO CAN COMMUNICATION SYSTEM. Refer to  HOW TO PROCEED WITH TROUBLESHOOTING [01/2019 - 09/2022] 

Result: 

A 

See step  5

1. Check for DTCs.

   Refer to DIAGNOSIS SYSTEM [01/2019 - 04/2020] , or refer to DIAGNOSIS SYSTEM [04/2020 - 09/2022]

   Result

   Result	Proceed to
   CAN system DTCs are not output	A
   CAN system DTCs are output	B

Result: 

B 

GO TO CAN COMMUNICATION SYSTEM. Refer to  HOW TO PROCEED WITH TROUBLESHOOTING [01/2019 - 09/2022] 

Result: 

A 

See step  6

1. Check for DTCs.

   Refer to DTC CHECK / CLEAR [01/2019 - 09/2022] 

   Result

   Result	Proceed to
   DTCs are output	A
   DTCs are not output	B

Result: 

B 

See step  8

Result: 

A 

See step  7

1. Refer to Diagnostic Trouble Code Chart.

   Refer to DIAGNOSTIC TROUBLE CODE CHART [01/2019 - 09/2022] 

   Result

   Proceed to
   NEXT

Result: 

NEXT 

See step  10

1. Refer to Problem Symptoms Table.

   Refer to PROBLEM SYMPTOMS TABLE [01/2019 - 09/2022] 

   Result

   Proceed to
   NEXT

Result: 

NEXT 

See step  9

1. Refer to Electronic Circuit Inspection Procedure.

   Refer to ELECTRONIC CIRCUIT INSPECTION PROCEDURE [06/2018 - ]

   Result

   Proceed to
   NEXT

Result: 

NEXT 

See step  10

1. Repair or replace parts based on the diagnosis result.

   Result

   Proceed to
   NEXT

Result: 

NEXT 

See step  11

1. Check the Data List to confirm that the tire inflation pressure has been received.

   Refer to DATA LIST / ACTIVE TEST [01/2019 - 09/2022] 

2. Perform initialization.

   Refer to INITIALIZATION [01/2019 - 09/2022] 

3. Confirm that the initialization has been completed.

   Result

   Proceed to
   NEXT

Result: 

NEXT 

END