Removal [09/2022 - 11/2022]: Procedure

1. When removing and storing the fuel tank assembly, arrange the fuel tank filler pipe assembly as shown in the illustration, and secure the fuel tank assembly using a cord or similar.
   NOTE:

   Depending on the arrangement of the fuel tank filler pipe assembly during storage, the fuel tank filler pipe assembly and rear suspension may interfere and cause fuel leakage.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   *a

   Cord

Refer to REMOVAL [09/2022 - 11/2022] 

Refer to REMOVAL [09/2022 - ]

1. w/ Rear Wheel House Front Plate:

   Remove the rear wheel house front plate.

   Refer to PROCEDURE - Step 1

2. Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   w/ No. 2 Floor Under Cover:

   1. Remove the 6 clips (A).
   2. Turn the 4 clips (B), clip (C) and remove the No. 2 floor under cover.
      NOTE:

      If the 5 clips are not turned when the No. 2 floor under cover is removed, the No. 2 floor under cover or stud bolt may be damaged.

      HINT: 

      Do not remove the clips from the No. 2 floor under cover.

3. Remove the 3 clips (A), clip (B), clip (C) and rear bumper side seal LH.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

4. w/o Rear Wheel House Front Plate:

   Remove the clip (A), 8 clips (B), 2 screws (C) and screw (D).

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

5. w/ Rear Wheel House Front Plate:

   Remove the clip (A), 8 clips (B) and 2 screws (C).

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

6. Remove the clip and rear wheel house liner LH.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

Refer to REMOVAL [01/2019 - ]

Refer to PROCEDURE - Step 2

Refer to PROCEDURE - Step 3

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Remove the fuel tank cap assembly from the fuel tank filler pipe assembly.

1. Remove the bolt.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

2. Disengage the locations shown in the illustration, and disconnect the fuel tank filler pipe assembly from the vehicle body.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Remove the 4 clips and No. 1 fuel tank protector from the fuel tank assembly.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Disconnect the No. 1 fuel evaporation tube sub-assembly from the fuel pipe.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Disconnect the fuel tank main tube sub-assembly from the fuel pipe.

   Refer to PRECAUTION [09/2022 - ]

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Support the fuel tank assembly using an engine lifter.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   HINT: 

   Using height adjustment attachments and plate lift attachments, keep the fuel tank assembly horizontal.

2. Remove the 4 bolts.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

3. Lower the engine lifter to remove the fuel tank assembly.
   NOTE:

   • Be careful not to drop the fuel tank assembly.
   • When removing the fuel tank assembly, tilt it slightly to prevent it from interfering with the surrounding parts.

1. Disengage the 3 clamps to remove the No. 1 fuel evaporation tube sub-assembly from the fuel tank assembly.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Disengage the 3 clamps to remove the fuel tank main tube sub-assembly from the fuel tank assembly.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Disconnect the charcoal canister outlet hose from the fuel tank filler pipe assembly.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

2. Disengage the 2 clamps to remove the charcoal canister outlet hose from the fuel tank assembly.