On-Vehicle Inspection [01/2019 - 09/2022]: Procedure

WARNING: This page is about a different car, the 2022 Toyota Corolla, 2021 Toyota Corolla, and 2020 Toyota Corolla. However, it is still accessible from the selected car via links, so may be relevant.

INSPECT SPEEDOMETER

NOTE:

The combination meter assembly receives the vehicle speed signal from the skid control ECU (brake booster with master cylinder assembly) via CAN communication. Therefore, perform the following inspection referring to values on the Data List of the skid control ECU (brake booster with master cylinder assembly) because it is the source of the vehicle speed signal.
Data List values of the skid control ECU (brake booster with master cylinder assembly) are used for this inspection. Therefore, make sure to perform this inspection after confirming that DTCs are not output.
If the tire size or tire inflation pressure is not within the specified range, or the tires are excessively worn, the speedometer indication error will increase. Therefore, make sure to perform this inspection after checking that the tire size, tire inflation pressure and tire wear are in the specified range.

Warm up the engine.
Connect the Techstream to the DLC3.
Turn the power switch on (IG).
Turn the Techstream on.
Enter the following menus: Chassis / ABS/VSC/TRAC / Data List.

Read the Data List according to the display on the Techstream.

Chassis > ABS/VSC/TRAC > Data List

Tester Display	Measurement Item	Range	Normal Condition	Diagnostic Note
Vehicle Speed	Maximum wheel speed sensor	Min.: 0 km/h (0 mph), Max.: 326.4 km/h (203 mph)	Vehicle stopped: 0 km/h (0 mph)	When driving at constant speed: No large fluctuations

Chassis > ABS/VSC/TRAC > Data List

Tester Display
Vehicle Speed

REFERENCE (FOR SPEEDOMETER WITH IMPERIAL UNITS FOR MAIN SCALE):

Techstream Indication (mph)	Acceptable Range (mph)
20	19.3 to 21.8
40	39.6 to 42.4
60	60.0 to 62.8
80	80.3 to 83.5
100	100.8 to 104.0
120	121.3 to 124.5
140	141.8 to 145.0

REFERENCE (FOR SPEEDOMETER WITH METRIC UNITS FOR MAIN SCALE):

Techstream Indication (km/h)	Acceptable Range (km/h)
20	18.5 to 22.5
40	38.8 to 43.3
60	59.2 to 63.7
80	79.4 to 84.4
100	99.9 to 104.9
120	120.4 to 125.4
140	140.9 to 145.9
160	161.3 to 166.3
180	181.8 to 186.8
200	202.3 to 207.3
220	222.8 to 227.8

Speedometer reading is within the acceptable range at each vehicle speed.

INSPECT TACHOMETER

Warm up the engine.
Connect the Techstream to the DLC3.
Turn the power switch on (IG).
Turn the Techstream on.
Enter the following menus: Powertrain / Hybrid Control / Data List.

Read the Data List according to the display on the Techstream.

Powertrain > Hybrid Control > Data List

Tester Display	Measurement Item	Range	Normal Condition	Diagnostic Note
Engine Speed	Engine speed	-	Engine stopped: 0 rpm While engine running at a constant speed: No significant fluctuation	-

Powertrain > Hybrid Control > Data List

Tester Display
Engine Speed

REFERENCE:

Techstream Indication (rpm)	Acceptable Range (rpm) Data in () is for Reference
700	630 to 770
1000	(900 to 1100)
2000	(1850 to 2150)
3000	2800 to 3200
4000	(3800 to 4200)
5000	4800 to 5200
6000	(5750 to 6250)

Tachometer reading is within the acceptable range at each engine speed.

INSPECT WARNING AND INDICATOR LIGHT ILLUMINATION (INITIAL CHECK)

Turn the power switch off.

Turn the power switch on (IG) or on (READY), and check the operation of the warning and indicator lights in the following table.

All of the lights illuminate and then turn off

Warning or Indicator Light
Brake warning light / red (malfunction)
SRS warning light
EPS warning light
MIL (Check engine warning light)
PCS warning light*
Slip indicator light
VSC OFF indicator light
ABS warning light
Brake warning light / yellow (minor malfunction)
Brake hold standby indicator light

*: w/ Forward Recognition Camera

HINT:

The illumination of each warning light and indicator light varies.