LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2024 >> Corolla LE >> Repair and Diagnosis >> External Pages >> Different car >> Section 376 (Seat Belt Warning System (HEV) - Diagnostics & Symptom Tests) >> SEAT BELT WARNING SYSTEM (for HV Model) >> Rear Seat Belt Warning Light Malfunction [01/2019 - 09/2019] >> Procedure

Rear Seat Belt Warning Light Malfunction [01/2019 - 09/2019]: Procedure

WARNING: This page is about a different car, the 2022 Toyota Corolla, 2021 Toyota Corolla, and 2020 Toyota Corolla. However, it is still accessible from the selected car via links, so may be relevant.
  1. READ VALUE USING TECHSTREAM (REAR DOOR COURTESY LIGHT SWITCH) 
    1. Connect the Techstream to the DLC3.
    2. Turn the power switch on (IG).
    3. Turn the Techstream on.
    4. Enter the following menus: Body Electrical / Main Body / Data List.
    5. Read the Data List according to the display on the Techstream.

      Body Electrical > Main Body > Data List 

      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      RR Door Courtesy SW Rear door courtesy light switch RH ON or OFF ON: Rear door RH open
      OFF: Rear door RH closed      		 -
      RL Door Courtesy SW Rear door courtesy light switch LH ON or OFF ON: Rear door LH open
      OFF: Rear door LH closed      		 -

      Body Electrical > Main Body > Data List 

      Tester Display
      RR Door Courtesy SW
      RL Door Courtesy SW

      OK

      The Techstream display changes correctly in response to the rear door condition.

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    GO TO LIGHTING SYSTEM. Refer to  Rear Door Courtesy Switch Circuit [01/2019 - 09/2022] 

    Result: 

    OK 

    See step  2

  2. CHECK REAR SEAT BELT WARNING 
    1. Check the rear seat belt warning function.
      GTY933613Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 Rear Seat Belt Warning Light (Combination Meter Assembly)
      *a LH
      *b Center
      *c RH

      Refer to ON-VEHICLE INSPECTION [01/2019 - 09/2019] 

      Result

      Result Proceed to
      The rear seat belt warning lights operation is normal A
      The rear seat belt warning lights (all seats) do not operate normally B
      The rear seat belt warning light (RH) does not operate normally C
      The rear seat belt warning light (center) does not operate normally D
      The rear seat belt warning light (LH) does not operate normally E

    Result: 

    A 

    USE SIMULATION METHOD TO CHECK. Refer to  PROBLEM SYMPTOMS TABLE [01/2019 - 04/2020]  

    Result: 

    B 

    REPLACE COMBINATION METER ASSEMBLY. Refer to  REMOVAL [01/2019 - 03/2019]  , or refer to  REMOVAL [03/2019 - 09/2022] 

    Result: 

    D 

    See step  5

    Result: 

    E 

    See step  7

    Result: 

    C 

    See step  3

  3. READ VALUE USING TECHSTREAM (REAR SEAT BELT BUCKLE SWITCH (FOR RH)) 
    1. Connect the Techstream to the DLC3.
    2. Turn the power switch on (IG).
    3. Turn the Techstream on.
    4. Enter the following menus: Body Electrical / Combination Meter / Data List.
    5. Read the Data List according to the display on the Techstream.

      Body Electrical > Combination Meter > Data List 

      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Rear Right Seat Buckle / Occupant Detection Warning Switch Rear seat inner with center belt RH buckle signal ON or OFF OFF: Rear RH seat belt fastened
      ON: Rear RH seat belt not fastened      		 -

      Body Electrical > Combination Meter > Data List 

      Tester Display
      Rear Right Seat Buckle / Occupant Detection Warning Switch

      Result

      Result Proceed to
      ON or OFF does not appear on the tester screen according to the rear seat belt condition A
      ON or OFF appears on the tester screen according to the rear seat belt condition B

    Result: 

    B 

    REPLACE COMBINATION METER ASSEMBLY. Refer to  REMOVAL [01/2019 - 03/2019]  , or refer to  REMOVAL [03/2019 - 09/2022] 

    Result: 

    A 

    See step  4

  4. CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - REAR SEAT 3 POINT TYPE BELT ASSEMBLY RH - BODY GROUND) 
    1. Disconnect the I5 combination meter assembly connector.
    2. Disconnect the O84 rear seat 3 point type belt assembly RH connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      I5-35 (RRSB) - O84-5 (RBR+) Always Below 1 Ω
      I5-35 (RRSB) or O84-5 (RBR+) - Body ground Always 10 kΩ or higher
      O84-4 (RBR-) - Body ground Always Below 1 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE REAR SEAT 3 POINT TYPE BELT ASSEMBLY RH. Refer to  REMOVAL [01/2019 - 04/2020] 

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

  5. READ VALUE USING TECHSTREAM (REAR SEAT BELT BUCKLE SWITCH (FOR CENTER)) 
    1. Connect the Techstream to the DLC3.
    2. Turn the power switch on (IG).
    3. Turn the Techstream on.
    4. Enter the following menus: Body Electrical / Combination Meter / Data List.
    5. Read the Data List according to the display on the Techstream.

      Body Electrical > Combination Meter > Data List 

      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Rear Center Seat Buckle / Occupant Detection Warning Switch Rear seat inner with center belt LH (for center) buckle signal ON or OFF OFF: Rear LH seat belt (for center) fastened
      ON: Rear LH seat belt (for center) not fastened      		 -

      Body Electrical > Combination Meter > Data List 

      Tester Display
      Rear Center Seat Buckle / Occupant Detection Warning Switch

      Result

      Result Proceed to
      ON or OFF does not appear on the tester screen according to the rear seat belt condition A
      ON or OFF appears on the tester screen according to the rear seat belt condition B

    Result: 

    B 

    REPLACE COMBINATION METER ASSEMBLY. Refer to  REMOVAL [01/2019 - 03/2019]  , or refer to  REMOVAL [03/2019 - 09/2022] 

    Result: 

    A 

    See step  6

  6. CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH (FOR CENTER) - BODY GROUND) 
    1. Disconnect the I5 combination meter assembly connector.
    2. Disconnect the O86 rear seat inner with center belt assembly LH (for center) connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      I5-19 (RCSB) - O86-1 (CBR+) Always Below 1 Ω
      I5-19 (RCSB) or O86-1 (CBR+) - Body ground Always 10 kΩ or higher
      O86-2 (CBR-) - Body ground Always Below 1 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH. Refer to  REMOVAL [01/2019 - 04/2020] 

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

  7. READ VALUE USING TECHSTREAM (REAR SEAT BELT BUCKLE SWITCH (FOR LH)) 
    1. Connect the Techstream to the DLC3.
    2. Turn the power switch on (IG).
    3. Turn the Techstream on.
    4. Enter the following menus: Body Electrical / Combination Meter / Data List.
    5. Read the Data List according to the display on the Techstream.

      Body Electrical > Combination Meter > Data List 

      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Rear Left Seat Buckle / Occupant Detection Warning Switch Rear seat inner with center belt LH (for LH) buckle signal ON or OFF OFF: Rear LH seat belt (for LH) fastened
      ON: Rear LH seat belt (for LH) not fastened      		 -

      Body Electrical > Combination Meter > Data List 

      Tester Display
      Rear Left Seat Buckle / Occupant Detection Warning Switch

      Result

      Result Proceed to
      ON or OFF does not appear on the tester screen according to the rear seat belt condition A
      ON or OFF appears on the tester screen according to the rear seat belt condition B

    Result: 

    B 

    REPLACE COMBINATION METER ASSEMBLY. Refer to  REMOVAL [01/2019 - 03/2019]  , or refer to  REMOVAL [03/2019 - 09/2022] 

    Result: 

    A 

    See step  8

  8. CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH (FOR LH) - BODY GROUND) 
    1. Disconnect the I5 combination meter assembly connector.
    2. Disconnect the O85 rear seat inner with center belt assembly LH (for LH) connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      I5-36 (RLSB) - O85-5 (LBR+) Always Below 1 Ω
      I5-36 (RLSB) or O85-5 (LBR+) - Body ground Always 10 kΩ or higher
      O85-4 (LBR-) - Body ground Always Below 1 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH. Refer to  REMOVAL [01/2019 - 04/2020] 

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

scientia non olet · About LEMON Manuals