LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2024 >> Corolla LE >> Repair and Diagnosis >> External Pages >> Different car >> Section 376 (Seat Belt Warning System (HEV) - Diagnostics & Symptom Tests) >> SEAT BELT WARNING SYSTEM (for HV Model) >> On-Vehicle Inspection [09/2019 - 04/2020] >> Procedure

On-Vehicle Inspection [09/2019 - 04/2020]: Procedure

WARNING: This page is about a different car, the 2022 Toyota Corolla, 2021 Toyota Corolla, and 2020 Toyota Corolla. However, it is still accessible from the selected car via links, so may be relevant.
  1. INSPECT DRIVER SEAT BELT WARNING LIGHT 

    HINT: 

    The seat belt warning light on the combination meter assembly is used for both the driver seat and front passenger seat.

    1. w/ Buzzer Regulated by Law
      1. Turn the power switch on (IG).
      2. When the driver seat belt is not fastened, check that the seat belt warning light on the combination meter assembly blinks for 6 seconds.

        Check that the seat belt warning light on the combination meter assembly changes from blinking to illuminated.

      3. Lift the vehicle using a swing arm type lift.

        Refer to VEHICLE LIFT AND SUPPORT LOCATIONS [06/2018 - 09/2022]

      4. Turn the power switch on (READY).
      5. Check the state of the seat belt warning light on the combination meter assembly under the following conditions:
        1. Step 1:

          When the driver seat belt is not fastened, the shift lever is in any position other than P and the parking brake is released, check that the seat belt warning light on the combination meter assembly blinks.

        2. Step 2:

          When the driver seat belt is not fastened and the vehicle is driven at approximately 20 km/h (12 mph) or more, check that the seat belt warning light on the combination meter assembly blinks.

          After 2 minutes, check that the seat belt warning light on the combination meter assembly changes from blinking to illuminated.

        3. Step 3:

          Starting from step 1 with the seat belt warning light on the combination meter assembly blinking, when the shift lever is moved to P, check that the seat belt warning light on the combination meter assembly changes from blinking to illuminated.

        4. Step 4:

          Starting from step 1 with the seat belt warning light on the combination meter assembly blinking, when the parking brake is applied, check that the seat belt warning light on the combination meter assembly changes from blinking to illuminated.

        5. Step 5:

          Starting from step 1 with the seat belt warning light on the combination meter assembly blinking, when the driver seat belt is fastened, check that the seat belt warning light on the combination meter assembly turns off.

    2. w/o Buzzer Regulated by Law
      1. Turn the power switch on (IG).
      2. When the driver seat belt is not fastened, check that the seat belt warning light on the combination meter assembly illuminates.
      3. Lift up the vehicle using a swing arm type lift.

        Refer to VEHICLE LIFT AND SUPPORT LOCATIONS [06/2018 - 09/2022]

      4. Turn the power switch on (READY).
      5. When the driver seat belt is not fastened, the parking brake is released and the vehicle is driven at approximately 1.75 km/h (1 mph) or more, check that seat belt warning light on the combination meter blinks at an interval of 1.2 seconds.
      6. When the driver seat belt is not fastened and the vehicle is driven at approximately 20 km/h (12 mph) or more, check that the seat belt warning light on the combination meter assembly blinks at an interval of 1.2 seconds for 24 seconds.

        After that, check that the seat belt warning light on the combination meter assembly blinks at an interval of 0.4 seconds for 100 seconds and then illuminates.

      7. When the driver seat belt is fastened, check that the seat belt warning light on the combination meter assembly turns off.
  2. INSPECT FRONT PASSENGER SEAT BELT WARNING LIGHT 

    HINT: 

    The seat belt warning light on the combination meter assembly is used for both the driver seat and front passenger seat.

    1. w/ Buzzer Regulated by Law
      1. Place a weight of 20 kg (44.0 lb) on the front passenger seat.
        NOTE:

        Place the weight on the seat cushion and allow it to come into contact with the seatback.

      2. Fasten the driver seat belt.
      3. Turn the power switch on (IG).
      4. Lift the vehicle using a swing arm type lift.

        Refer to VEHICLE LIFT AND SUPPORT LOCATIONS [06/2018 - 09/2022]

      5. Turn the power switch on (READY).
      6. Check the state of the seat belt warning light on the combination meter assembly under the following conditions:
        1. Step 1:

          When the front passenger seat belt is not fastened, the shift lever is in any position other than P and the parking brake is released, check that the seat belt warning light on the combination meter assembly blinks.

        2. Step 2:

          When the front passenger seat belt is not fastened and the vehicle is driven at approximately 20 km/h (12 mph) or more, check that the seat belt warning light on the combination meter assembly blinks.

          After 2 minutes, check that the seat belt warning light on the combination meter assembly changes from blinking to illuminated.

        3. Step 3:

          Starting from step 1 with the seat belt warning light on the combination meter assembly blinking, when the shift lever is moved to P, check that the seat belt warning light on the combination meter assembly changes from blinking to illuminated.

        4. Step 4:

          Starting from step 1 with the seat belt warning light on the combination meter assembly blinking, when the parking brake is applied, check that the seat belt warning light on the combination meter assembly changes from blinking to illuminated.

        5. Step 5:

          Starting from step 1 with the seat belt warning light on the combination meter assembly blinking, with the front passenger seat belt not fastened and the weight on the front passenger seat, check that the seat belt warning light on the combination meter assembly turns off when the weight is removed from the front passenger seat.

        6. Step 6:

          Starting from step 1 with the seat belt warning light on the combination meter assembly blinking, when the front passenger seat belt is fastened, check that the seat belt warning light on the combination meter assembly turns off.

    2. w/o Buzzer Regulated by Law
      1. Turn the power switch on (IG).
      2. Place a weight of 20 kg (44.0 lb) on the front passenger seat.
        NOTE:

        Place the weight on the seat cushion and do not allow it to come into contact with the seatback.

      3. Fasten the driver seat belt.
      4. When the front passenger seat belt is not fastened, check that the seat belt warning light on the combination meter assembly illuminates.
      5. Lift the vehicle using a swing arm type lift.

        Refer to VEHICLE LIFT AND SUPPORT LOCATIONS [06/2018 - 09/2022]

      6. Turn the power switch on (READY).
      7. When the front passenger seat belt is not fastened, the parking brake is released and the vehicle is driven at approximately 1.75 km/h (1 mph) or more, check that seat belt warning light on the combination meter blinks at an interval of 1.2 seconds.
      8. When the front passenger seat is occupied, the front passenger seat belt is not fastened and the vehicle is driven at approximately 20 km/h (12 mph) or more, check that the seat belt warning light on the combination meter assembly blinks at an interval of 1.2 seconds for 24 seconds.

        After that, check that the seat belt warning light on the combination meter assembly blinks at an interval of 0.4 seconds for 100 seconds and then illuminates.

      9. When the front passenger seat belt is fastened, check that the seat belt warning light on the combination meter assembly turns off.
  3. INSPECT REAR SEAT BELT WARNING LIGHT (w/ Rear Seat Belt Warning) 
    1. Check the state of the rear seat belt warning light on the combination meter assembly:
      GTY871970Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 Rear Seat Belt Warning Light (Combination Meter Assembly)
      *a LH
      *b Center
      *c RH
      1. Turn the power switch off.
      2. Turn the power switch on (IG).
      3. When a rear seat belt is not fastened, check that the rear seat belt warning light on the combination meter assembly is illuminated.
      4. After 66 seconds, check that the rear seat belt warning light on the combination meter assembly turns off.
      5. When one of the rear seat belts is unfastened from being fastened, check that the rear seat belt warning light on the combination meter assembly illuminates.
  4. INSPECT SEAT BELT WARNING BUZZER 

    HINT: 

    The seat belt warning buzzer can be customized. Make sure that this function is ON.

    Refer to CUSTOMIZE PARAMETERS [01/2019 - 04/2020] 

    1. for Front Seat Belt Warning Buzzer (w/ Buzzer Regulated by Law):
      1. Place a weight of 20 kg (44.0 lb) on the front passenger seat.
        NOTE:

        Place the weight on the seat cushion and allow it to come into contact with the seatback.

      2. After turning the power switch on (IG), wait for approximately 1.8 seconds with the driver seat belt not fastened check that the seat belt warning buzzer in the combination meter assembly sounds at an interval of 1.2 seconds for 6 seconds.
      3. Lift the vehicle using a swing arm type lift.

        Refer to VEHICLE LIFT AND SUPPORT LOCATIONS [06/2018 - 09/2022]

      4. Start the power switch on (READY).
      5. When the driver or front passenger seat belt is not fastened and the vehicle is driven at approximately 20 km/h (12 mph) or more, check that the seat belt warning buzzer in the combination meter assembly sounds once.
      6. When 24 seconds have passed after the buzzer sounded, check that the seat belt warning buzzer in the combination meter assembly sounds at an interval of 1.2 seconds for 6 seconds.
      7. After the seat belt warning buzzer has been sounding for 6 seconds at an interval of 1.2 seconds, check that the seat belt warning buzzer in the combination meter assembly sounds at an interval of 0.4 seconds for 90 seconds.
      8. Check that the seat belt warning buzzer in the combination meter assembly stops 96 seconds after it started sounding at an interval of 1.2 seconds.
      9. After the seat belt warning buzzer in the combination meter assembly stops, turn the power switch off and then turn the power switch on (READY). Drive the vehicle at approximately 20 km/h (12 mph) or more with either the driver or front passenger seat belt not fastened and check that the buzzer sounds in the same pattern again.
      10. After the seat belt warning buzzer in the combination meter assembly stops, fasten the driver or front passenger seat belt, drive the vehicle at approximately 20 km/h (12mph) or more, unfasten the driver or front passenger seat belt and check that the buzzer sounds in the same pattern again.
    2. for Front Seat Belt Warning Buzzer (w/o Buzzer Regulated by Law):
      1. Place a weight of 20 kg (44.0 lb) on the front passenger seat.
        NOTE:

        Place the weight on the seat cushion and allow it to come into contact with the seatback.

      2. Lift the vehicle using a swing arm type lift.

        Refer to VEHICLE LIFT AND SUPPORT LOCATIONS [06/2018 - 09/2022]

      3. Turn the power switch on (READY).
      4. When the driver or front passenger seat belt is not fastened and the vehicle is driven at approximately 20 km/h (12 mph) or more, check that the seat belt warning buzzer in the combination meter assembly sounds at an interval of 1.2 seconds for 24 seconds.
      5. After the seat belt warning buzzer has been sounding for 24 seconds at an interval of 1.2 seconds, check that the seat belt warning buzzer in the combination meter assembly sounds at an interval of 0.4 seconds for 100 seconds.
      6. Check that the seat belt warning buzzer in the combination meter assembly stops 124 seconds after it started sounding at an interval of 1.2 seconds.
      7. After the seat belt warning buzzer in the combination meter assembly stops, turn the power switch off and then turn the power switch on (READY). Drive the vehicle at approximately 20 km/h (12 mph) or more with either the driver or front passenger seat belt not fastened and check that the buzzer sounds in the same pattern again.
      8. After the seat belt warning buzzer in the combination meter assembly stops, fasten the driver or front passenger seat belt, drive the vehicle at approximately 20 km/h (12mph) or more, unfasten the driver or front passenger seat belt and check that the buzzer sounds in the same pattern again.
    3. for Rear Seat Belt Warning Buzzer (w/ Rear Seat Belt Warning):
      1. Lift the vehicle using a swing arm type lift.

        Refer to VEHICLE LIFT AND SUPPORT LOCATIONS [06/2018 - 09/2022]

      2. Fasten the driver seat belt.
      3. Turn the power switch on (READY).
      4. Fasten and unfasten a rear seat belt then drive the vehicle at approximately 20 km/h (12 mph) or more and check that the seat belt warning buzzer in the combination meter assembly sounds once.
      5. When 24 seconds have passed after the buzzer sounded, check that the seat belt warning buzzer in the combination meter assembly sounds at an interval of 1.2 seconds for 6 seconds.
      6. After the seat belt warning buzzer has been sounding for 6 seconds at an interval of 1.2 seconds, check that the seat belt warning buzzer in the combination meter assembly sounds at an interval of 0.4 seconds for 30 seconds.
      7. Check that the seat belt warning buzzer in the combination meter assembly stops 36 seconds after it started sounding at an interval of 1.2 seconds.
      8. After the seat belt warning buzzer in the combination meter assembly stops, turn the power switch off and then start the engine. Fasten and unfasten a rear seat belt then drive the vehicle at approximately 20 km/h (12 mph) or more and check that the buzzer sounds in the same pattern again.
      9. After the seat belt warning buzzer in the combination meter assembly stops, fasten a rear seat belt, drive the vehicle at approximately 20 km/h (12mph) or more, unfasten the rear seat belt and check that the buzzer sounds in the same pattern again.
scientia non olet · About LEMON Manuals